Honeywell RPWL800A1002/W Support Question
Honeywell RPWL800A1002/W Support Question
Find answers below for this question about Honeywell RPWL800A1002/W - Honeyywell VisioCam Wireless Camera/Push Button.Need a Honeywell RPWL800A1002/W manual? We have 1 online manual for this item!
Question posted by smartj1587 on September 8th, 2011
Won't Turn On
Hi, the batteries died on my grandmother's unit. I replaced them with the right type of battery. We can here dings, but there is no video on the little device or on the tv that it is hooked up to.
Current Answers
Related Honeywell RPWL800A1002/W Manual Pages
Owner's Manual - Page 1
Installation and Use
VISIOCAMTM RCWL8000A and RPWL800A
Wireless Video Chime System
69-2108EFS_A.indd 1
69-2108EFS-01
11/30/2007 1:51:44 PM
Owner's Manual - Page 2
...next page.)
THE VISIOCAM SYSTEM
Your Honeywell wireless video entry system uses radio signals to transmit a video picture of the caller from the door camera to ensure correct ...Door Camera 4 Door Camera TransformerOption 7
Installing the receiver 8 Receiver Operation 8 Door Camera 10
Expanding Your System 11
Maintenance and Use 12 Care and Maintenance 12 Replacing the Receiver Batteries...
Owner's Manual - Page 3
...
- FOR SECOND CAMERA/PUSH
RCA SOCKET - TO CONNECT TO A TV SET (OPTIONAL)
CHIME FLASHER
BATTERY INDICATOR
MIC VOLUME - Remove the two screws at the base of the camera unit and unhook and release the camera base, pulling it away from the lower end first. FOR FUTURE USE
Scan
DISPLAY
BRIGHTNESS
CHIME VOLUME
SCAN BUTTON
- Once the batteries have been...
Owner's Manual - Page 4
... and carefully push it back into the slot.
2. Follow the plus (+) and minus (-) signs on the diagram inside the battery compartment.
Never mix old and new batteries.
3. Installation and Use
Pre-installation setup
Note: Removing the cover also provides access to the nameplate, so now is an option to power the door
camera using an...
Owner's Manual - Page 5
... next step, leave the unit to be fully charged. VISIOCAM
2
Program the door camera into the receiver, the receiver remains active in use: this is normal.
the chime tunes play once the batteries have enough power for the LCD screen.
To program the door camera into a suitable mains socket.
Note that the batteries have enough power.
Place the...
Owner's Manual - Page 6
...VIEW
57 57
VERTICAL
41 41
• The camera is adjustable through a 30° total angle left to right, and 60° top to be between ...unit.
• Do not mount within 12 in . [40 cm] thick) construction - Installation and Use
Installing the door camera
Position the door camera
Find a position for the door camera where the call button is easy to press and the camera can 'see 'Door camera...
Owner's Manual - Page 7
... selected mounting position and press the call button is pressed, then there are powered up in their planned position(s), to check that there is nearby interference on the video channel. The units may need to adjust the camera lens to the troubleshooting section for example, CH 3. The door camera has not been programmed into the receiver...
Owner's Manual - Page 8
... will affect the internal parts. Hook the door camera into the base at the top first, then push and click it away from rain damage. If mounting to seal the unit from the base. Insert the two screws underneath, and tighten.
Remove the two screws underneath the door camera. The distance between mounting holes is evenly...
Owner's Manual - Page 9
..., mains supply. Note: If you have not used the door camera with batteries for a trial test, then you must program the door camera with a water seal is .2 in (5 mm). Installing the door camera
VISIOCAM
Door camera transformer option
For installations where there is fully and evenly pressed in to seal the unit against rain damage.
3.
The cable run should illuminate. Leave...
Owner's Manual - Page 10
... caller presses the call button, then adjust the receiver display for about thirty
seconds. Display brightness
Activate the door camera by using the four position slide switch.
Before mounting in position 0 or 2*.
Video transmission
is in place, check that the receiver can be set to 0) and the camera image is charging. era battery life and is...
Owner's Manual - Page 11
..., so they can be changed by pressing the ' ' button. Check outside immediately. The alert tone is unaffected by nearby 2.4GHz video receiving devices.
69-2108EFS_A.indd 9
69-2108EFS-01
11/30/2007 1:51:49 PM
Replace the batteries in the door camera.
Adjust for a second door camera or a door push. Installing the receiver
VISIOCAM
Chime tune selection
The receiver chime tune can...
Owner's Manual - Page 12
... two seconds to confirm. To switch the motion sensor off, press and hold the call button on .
69-2108EFS-01
10
69-2108EFS_A.indd 10
11/30/2007 1:51:49 PM...camera or a change of batteries will reset the sensor back on the camera for approximately 30 seconds. The receiver produces a 'ping' sound and displays the door camera image for more than ten seconds. Installation and Use
Door camera...
Owner's Manual - Page 13
... door camera or bell push:
Press and hold the ' ' button for more cameras, for example.
Adding a door push
The receiver will respond to up to four door cameras. Additional door cameras
The receiver will respond to a Visiocam door push.
The unit must be set on the new unit to program it in this section. Note: The video receiver does not respond to a door push while the video...
Owner's Manual - Page 14
... unit in dusty, dirty areas. Do not use or store either unit....REPLACING THE RECEIVER BATTERIES
Constant use
CARE AND MAINTENANCE
• Fingerprints or dirt on the door camera lens can cause a dull or blurred picture. Remove the old batteries and replace with three NiMH type
AA batteries with a minimum capacity of the receiver. Replace the batteries by unscrewing the
single battery...
Owner's Manual - Page 15
... the video quality.
Open the door camera and change the video channel switch from the units. The receiver chimes, followed by a beep-beep... Receiver is facing a very black surface.
Replace the door camera batteries.
13
69-2108EFS-01
69-2108EFS_A.indd 13
11/30/2007 1:51:49 PM Troubleshooting
VISIOCAM
The system does not work... • Make sure the door camera is...
Owner's Manual - Page 16
...video signal has been interrupted. The tone may sound if the screws that mount the front of the door camera to the 'DOOR CAMERA' section), block off the unwanted movement, or relocate the door camera.
Chime sounds but the picture is low. Press any button...; The battery charge is displayed for at least four hours to the door unit, or place the
receiver higher up on the camera picking up...
Owner's Manual - Page 17
... batteries, minimum 1200mAh
Battery operating life
typically one year*
typically 3 days from full charge*
Motion sensor range
12 ft. (4 m) typical (fixed sensitiv- ASpbeocuitfiycoautironnesw thermostat
VISIOCAM
Door Camera
Receiver
Power requirement
110V AC ±10% via 8V to 10V 1A bell transformer** N/A or 8-12V AC or DC supply
Maximum number of transmitters N/A (video or door push...
Owner's Manual - Page 18
GUARANTEE Honeywell guarantees this does not affect your statutory rights. Honeywell International Inc. The charging base is in compliance ...may cause undesired operation. this product for recycling advice.
This device operation is required; on recycled paper containing at 1-800-468-1502
DISPOSAL AND RECYCLING Batteries and waste electrical products should not be disposed of with ...
Similar Questions
There Was No Push Button In The Box! Luckily We Already Had One But The New Doo
there was no push button in the box but luckily we still had the old one up. New door bell won't chi...
there was no push button in the box but luckily we still had the old one up. New door bell won't chi...
(Posted by Eleanorhawking 6 years ago)
Can I Buy A Replacement Push Button For The Honeywell Rcwl210?
Need a new push button for the RCWL210 remote door chime. This part number 51381SL Rev 1 in white. W...
Need a new push button for the RCWL210 remote door chime. This part number 51381SL Rev 1 in white. W...
(Posted by rjcone1 11 years ago)
I Cant Get It To Ring Lost My Remote But Have New Batteries In It51376sl
just want it to ring again when i push button... my brother used it before he died of cancer ... did...
just want it to ring again when i push button... my brother used it before he died of cancer ... did...
(Posted by winchestergrama 11 years ago)
Wireless Door Bell Not Working
We have a Hoenywell portable plus chime door bell. the button outside works when it wants to, and us...
We have a Hoenywell portable plus chime door bell. the button outside works when it wants to, and us...
(Posted by daw56 12 years ago)
