Honeywell 191108AJ Support Question
Honeywell 191108AJ Support Question
Find answers below for this question about Honeywell 191108AJ.Need a Honeywell 191108AJ manual? We have 1 online manual for this item!
Question posted by ladennen on January 20th, 2012
Honeywell Thermostat
where is the serial # so that we can download a manual. We need to find out how to reset the temp control as the temps go up to 82 at night. When we take the casing off the wall, there is a silver bar part with the # aube 350-000-071-B. and a green board with 3 prongs on either side with the # 200-631-001-B with 05/2007 underneath. But, we can't find either of these #s on the website to download a manual
Current Answers
Related Honeywell 191108AJ Manual Pages
Owner's Manual - Page 1
T8190A/191108AJ, Q682
Heating or Cooling Thermostat and Wallplate
or Heating/Cooling Thermostat and Subbase
D.F. Rev. 9-94
©Honeywell Inc. 1994 Form Number 69-0643-1
M3375
Owner's Manual - Page 2
... (or returning home) to significantly lower your new Honeywell thermostat. This allows you to a comfortable temperature. Recycling Notice M3375
This control contains mercury in the trash at the end of an old control containing mercury in the trash. Do not place control in a sealed tube.
If this control is your home one or more times every...
Owner's Manual - Page 3
Table of Contents
Page Features of Your Thermostat ...4 Setting the Temperature ...7 Inserting Timer Batteries ...8 Setting the Timer ...9 Programming ...10 Setting Subbase Switches ...13 Troubleshooting ...14 Servicing the Thermostat ...22
Cycle Rate Adjustment ...22 Thermometer Adjustment ...23 Warranty ...27
3
69-0643-1
Owner's Manual - Page 4
FeaturesOf Your Thermostat
4
1
2
3
M7349
1 FLIP-UP COVER. Left (blue mark) controls the low temperature, right (red mark) controls the high temperature.
5 TIMER. Arrow head (triangle
shape) indicates low (blue) temperature setting or high (red) temperature setting in control on 24-hour dial.
4
69-0643-1 Lift up to adjust heat anticipator.
3 THERMOMETER. Turn clockwise to match...
Owner's Manual - Page 6
ordered separately.) Provides mounting base, wiring connections and manual switching control for heating-only or cooling-only thermostat.
15
16 SUBBASE (Optional, not included with thermostat.) Provides mounting base and wiring connections for heating/cooling thermostat. 15 WALLPLATE (Included with thermostat; See Setting Subbase Switches section for additional information.
16
6
M2421
R...
Owner's Manual - Page 8
... Vac transformer, by two AAA alkaline batteries (included), or by the heating or cooling control circuit. We recommend Energizer® batteries. INSTALL WITH POSITIVE ENDS UP
M8585
Fig. ...year or when batteries are dead, replace with two new AAA alkaline batteries. Install batteries in thermostat as shown in Fig. 2.
Inserting Timer Batteries
Power is interrupted when using a 24 Vac ...
Owner's Manual - Page 9
... the time indicator arrow will point to the light band.
Setting the Timer
■ Lift thermostat flip-up cover and you'll find the 24-hour program dial, slotted in a clockwise ... in 10-minute increments. Adjust the timer to the correct time and corresponding daytime (light) or night-time (dark) band of the program dial. PROGRAM DIAL
PROGRAM PIN (6)
TIMER SETTING KNOB
TIME INDICATOR...
Owner's Manual - Page 10
... the number of program pins used. A red pin is slotted for high
PROGRAM PINS
THERMOSTAT COVER
PROGRAM PIN SLOT
PROGRAM INDEX WHEEL TIME INDICATOR ARROW
PROGRAM PIN STORAGE
M7348
Fig.... DIAL (GRAY AREA FOR NIGHT SETTINGS)
Before setting your program
Notice the slots on the program dial (Fig. 4) are for the program pins that can program your thermostat. Programming
You can be ...
Owner's Manual - Page 13
... and fan coil systems, the fan is off . OFF-Both the heating and cooling systems are off . AUTO-Fan operates with cooling equipment as
controlled by the thermostat in detent over desired function indicator mark.
13
69-0643-1 To switch positions, use thumb or index finger to slide the lever to the...
Owner's Manual - Page 14
...on power. Problem No heat. 2
Check - If blown or tripped, replace fuse or reset breaker. Firmly tighten all terminal screws. Pilot flame may be in OFF
or COOL position...any frayed or broken wires. Thermostat connections.
- Turn off power to furnace manufacturer instructions. Fuse or circuit breaker. -
Troubleshooting
Your Honeywell thermostat requires little or no attention. ...
Owner's Manual - Page 15
... temperatures. Program pins for proper day
or night phase.
- Position of thermostat set point levers.
- Positions of subbase system switch (heating-cooling model). Relocate pins to warm up at the
programmed
time.
2
Temperature change occurs at the wrong time. Timer program for heating system may need more time to desired settings. Troubleshooting (Continued...
Owner's Manual - Page 16
...Room temperatures are not correct (continued).
Anticipator setting. (See Fig. 6
long. Observe burner operation.
(continued)
16
69-0643-1 Heating system should start . Observe burner operation.
Thermostat circuits. Increase anticipator setting by 0.05 (e.g., 0.45 to 0.45). for anticipator location.)
Burner-on time too short.
- If the system does not operate, call a qualified...
Owner's Manual - Page 17
... broken wires. Move to COOL position.
Other.
17
Action Move switch to ON position. Turn off .
- If fuse is blown or breaker tripped, replace or reset.
Troubleshooting (Continued)
Problem No cooling. 1
Check
- Condenser switch position. Thermostat connections. Fuse or circuit breaker.
- System switch may be in OFF or HEAT position.
-
Owner's Manual - Page 18
...to run.
- Area around thermostat for change of thermometer.
-Thermostat connections at the two C terminals. Troubleshooting (Continued)
Problem
Thermostat setting and thermometer reading disagree. Timer does not run .
18
Action Reinstall thermostat wallplate or subbase. Level position of thermostat.
- Thermostat should be about 5 ft [1.5m] above floor on an inside wall. If new batteries...
Owner's Manual - Page 19
... seated in program dial. Push down on pins to system.
19
Action Remove thermostat from the wallplate or subbase and measure the voltage.
Troubleshooting (Continued)
Problem
Check... backup batteries as shown in program dial. Reset timer. Filter may be clogged.
Replace filter and reset timer.
(continued) 69-0643-1 High limit control. Safety limit on equipment can occur.
-...
Owner's Manual - Page 20
...
20
69-0643-1 If this Troubleshooting section did not solve the problem, call a qualified service technician or the Honeywell Customer Assistance Center, 1-800-468-1502, Monday - Check - Troubleshooting (Continued)
Problem Timer loses time (continued). ...only system. 3 If timer is not battery powered, timer may need
replacement. Friday, 7:00 AM to 5:30 PM Central time for backup.
Owner's Manual - Page 21
.... Limit switch contacts stuck open.
-
Transformer supplying power is inadequate.
- Free or replace limit switch. - Replace thermostat.
21
69-0643-1 Check - System transformer used to power the timer is burned out.
- Spring fingers on thermostat not making proper contact with proper secondary voltage.
- Replace wiring. - Use additional (separate) transformer.
-
Additional...
Owner's Manual - Page 22
NOTE: Most hot water systems require a setting of 1.2A. ANTICIPATOR SCALEPLATE
ANTICIPATOR SETTING LEVER
M7317
Fig. 6-Heat anticipator setting.
22
69-0643-1 Servicing the Thermostat
Cycle Rate Adjustment
The equipment should cycle on and off just enough to keep the room temperature close to cycle the heating system too fast ...
Owner's Manual - Page 23
...open the flip-up cover. then compare the readings. Replace thermostat cover and put the system into operation.
Be careful not to sense area temperature; Allow at the factory and should only need adjustment if it until both thermometers read the same. If... FLIP-UP COVER
INSERT AND TURN SCREWDRIVER
M1810
Fig. 7-Thermometer adjustment.
23
69-0643-1 Set the thermostat cover on it.
Owner's Manual - Page 24
If you have questions regarding the installation and programming of your Honeywell thermostat, please visit our web site at www.honeywell.com/yourhome or call the 24-hour automated information line at 1-800-468-1502.
24
69-0643-1
Similar Questions
Want To Replace An Old Honeywell Thermostat Model With A Newer Updated Model.
I want to replace a manual Honeywell Chronotherm Thermostat with an updated digital type. The model ...
I want to replace a manual Honeywell Chronotherm Thermostat with an updated digital type. The model ...
(Posted by Wjvivola 3 years ago)
Possible Thermostat Malfunction, Causing Problems For Growing Plants.
Hello. I work in a medicinal marijuana grow, and have 15 grow lights running. We were using a Rheem ...
Hello. I work in a medicinal marijuana grow, and have 15 grow lights running. We were using a Rheem ...
(Posted by alan1breath 5 years ago)
I Lost My Manual For My 7 Day Digital Honeywell Thermostat Aube 350-000-071-b.
The number I have provided is on a bar on the inside of the thermostat. I did not see a model number...
The number I have provided is on a bar on the inside of the thermostat. I did not see a model number...
(Posted by lrenglish 7 years ago)
Yourhome Honeywell Thermostat Owners Manualmodel Ct3200a1019(1) 0531pf1a
I have a Honeywell thermostat, model CT 3200A1019(1). There is another number on the thermostat: 053...
I have a Honeywell thermostat, model CT 3200A1019(1). There is another number on the thermostat: 053...
(Posted by joebernat 10 years ago)
How To Connect A Thermostat
How do I connect a t834n single stage thermostat to a 3wire system
How do I connect a t834n single stage thermostat to a 3wire system
(Posted by Marcellinc36 10 years ago)