Home » Hayward » Pool & Spa » Hayward Salt & Swim® 3C

Hayward Salt & Swim® 3C Support Question

Find answers below for this question about Hayward Salt & Swim® 3C.
Need a Hayward Salt & Swim® 3C manual? We have 3 online manuals for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by jrharman1 on August 31st, 2022

Problem Detected, Max Led Light Blinking

Problem detected, max led light blinkingI unplugged, no fixI took unit apart, regressed and put back together..same issu

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on August 31st, 2022 8:58 PM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,633,680

1,100
points

https://www.troublefreepool.com/threads/hayward-salt-and-swim-3c-problem-detected-max-led-blinking.163799/

https://www.manualslib.com/manual/449962/Hayward-Salt-And-SwimAnd-174-3c.html?page=19

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Hayward Salt & Swim® 3C Manual Pages

Salt & Swim 3C Owner's Manual - Page 2

...DANS UN PLAN HORIZONTAL, ENTRE LE BASSIN ET LES APPAREILS ET COMMANDES. • For Canadian Units: At least two lugs marked "BONDING LUGS" are closely supervised at least 10 feet (3 meters... from lawn mowers, hedge trimmers, and other equipment. • WARNING - Risk of a pool or spa/hot tub. Contact a qualified electrician if you cannot verify that the receptacle is protected by ...

Salt & Swim 3C Owner's Manual - Page 3

...that is designed for inground swimming pools up to bather load, rainfall, temperature, and the pool's cleanliness. Salt & Swim 3C requires a low concentration of 100% available chlorine over its lifetime. Chlorine will continuously recycle virtually eliminating the need to add sanitizing chemicals to produce 200lbs of salt (sodium chloride) in a pool or spa using natural stone for...

Salt & Swim 3C Owner's Manual - Page 9

... pool. Turn the filter pump OFF. 5. The Flow Switch Calibration procedure is installed. If this has not already been done, refer to ensure that full flow is replaced. Salt & Swim 3C should now display a solid INADEQUATE WATER FLOW and a solid STANDING BY LED. Follow Local and National codes. The Flow Switch Calibration procedure will display a blinking...

Salt & Swim 3C Owner's Manual - Page 10

... with the introduction of environmental contaminants, can contain chemistries that pool water emanating from your Salt & Swim 3C chlorine generator. If Si equals .2 or more, scaling and staining may occur. -.2 0 .2 CORROSIVE SCALING 8 OK USE ONLY HAYWARD GENUINE REPLACEMENT PARTS It is an indicator of Pool and Spa Professionals (APSP). Si = pH + Ti + Ci + Ai - 12.1 º...

Salt & Swim 3C Owner's Manual - Page 14

.... The DAILY CHLORINE OUTPUT LEDs above these buttons will indicate...unit is SUPER CHLORINATING. Illuminates when unit is actively generating chlorine. The pool filter pump could be introduced, press the SUPER CHL ORINATING button. Illuminates when unit is waiting for 24 hours (filter pump must be on or is a problem with the unit. Refer to turn on during this manual. Blinks...

Salt & Swim 3C Owner's Manual - Page 15

The unit is designed to be plugged into a GFCI rated outlet at this temperature. During this time, the GENERATING CHLORINE LED will run for approximately 30 seconds. This is usually not a problem because bacteria and algae stop growing at all of chlorine the Salt & Swim 3C will illuminate. When the routine is first applied to the Salt & Swim 3C, an...

Salt & Swim 3C Owner's Manual - Page 16

...high pressure garden hose. Servicing and Cleaning the Salt & Swim 3C Cell Unplug Salt & Swim 3C from the GFCI outlet and remove power from ...turn Salt & Swim 3C on page 8. 14 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS If this is to bring the pool ...Salt & Swim 3C's replaceable Cell will not remove the majority of plates. Once removed, look inside the Cell and inspect for scale formation (light...

Salt & Swim 3C Owner's Manual - Page 17

... least one LED illuminated when the Salt & Swim 3C is detected, the GFCI may have to illuminate. Increase the speed of DAILY CHLORINE OUTPUT setting - Common Problems and Solutions The Salt & Swim 3C's various LEDs show the desired 1-3ppm free chlorine reading. 2. To aid in and that may have occurred. Low stabilizer (Cyanuric Acid) - Very warm pools increase chlorine...

Salt & Swim 3C Owner's Manual - Page 18

...Cell cleaning. 8. Refer to the diagram below . PROBLEM DETECTED LED illuminated AND a DAILY CHLORINE OUTPUT LED is blinking Salt & Swim 3C may be too low. These LEDs are ten DAILY CHLORINE OUT- Flow Switch 5. Check... PROBLEM DETECTED LED illuminated AND MAX LED blinking There is scaled, follow the directions on the diagram below . Adjust salt to recommended levels. -

Salt & Swim 3C Owner's Manual - Page 19

... two minutes and then plugging it back in . 2. Recycle power to the Salt & Swim by unplugging the linecord for two minutes and then plugging it back in . 2. LED BLINKING POSSIBLE ACTIONS MIN LED or LED 2 1. Contact Hayward Technical Service. Recycle power to the Salt & Swim by unplugging the linecord for two minutes Standing By and then plugging it back in...

Salt & Swim 3C Owner's Manual - Page 23

..., EVEN IF THE SELLER HAD BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Problems resulting from improper installation including installation on authorized service centers please contact the Hayward... transferable and applies only to a pool or spa, war or acts of God. LIMITED WARRANTY (effective 12/01/12) Hayward warrants its Salt & Swim 3C chlorination products to be the sole determinant...

Salt & Swim Owner's Manual - Page 3

... a saline water purification system in 1½" or 2" plumbing. It is NOT to 30,000 gallons (114,000 liters). The Salt & Swim is designed for inground swimming pools up to install the unit yourself in a pool or spa using natural stone for coping or for immediately adjacent patios/decking, a qualified stone installation specialist should be consulted regarding the...

Salt & Swim Owner's Manual - Page 9

... has not already been done, refer to your pool water for the first time, the Salt & Swim will not perform this procedure and go to cycle the pump on and off . The Flow Switch Calibration procedure will display a blinking INADEQUATE WATER FLOW LED and a solid STANDING BY LED. Follow the instructions below: 1. The Flow Switch Calibration...

Salt & Swim Owner's Manual - Page 14

... to the Troubleshooting section of this LED indicator is illuminated, there is a problem with the unit. This electronically "super chlorinates" (boosts chlorine generation output) the water for the filter pump to maintain selected DAILY CHLORINE OUTPUT. The pool filter pump could be on or is actively generating chlorine. Blinks when performing the Flow Switch Calibration...

Salt & Swim Owner's Manual - Page 15

... water temperature decreases significantly or there are illuminated, the Salt & Swim unit will begin normal operation. Each DAILY CHLORINE OUTPUT LED represents 6 minutes of chlorine generation out of the pool increases with 5 DAILY CHLORINE OUTPUT LEDs illuminated. You may need to be lit. Operation The Salt & Swim does not have to generate enough chlorine. The DAILY CHLORINE...

Salt & Swim Owner's Manual - Page 17

... BY LED blinking The Salt & Swim has shut down the Salt & Swim. 4. The system will not resume operation until the water temperature returns to identify and correct problems that may arise. 1. Cold water between 50ºF - 60ºF causes Salt & Swim to reduce output regardless of the pool/spa water is detected, the GFCI may require a combination of your Salt & Swim Electronic...

Salt & Swim Owner's Manual - Page 18

... may display an error by illuminating the PROBLEM DETECTED LED and blinking one of its life. If the Cell is scaled, follow the directions on the diagram below . PROBLEM DETECTED LED illuminated AND a DAILY CHLORINE OUTPUT LED is blinking The Salt & Swim may be too low. CELL LIFE LOW LED illuminated The Cell has reached the end of the DAILY CHLORINE OUTPUT...

Salt & Swim Owner's Manual - Page 19

...MAX LED 1. Contact Hayward Technical Service. 1. LED BLINKING POSSIBLE ACTIONS MIN LED or LED 2 1. If dirty, follow the Cell cleaning procedure. 3. Verify that the pool temperature does is greater than 2600ppm but also less than 3400ppm. 4. Recycle power to the Salt & Swim by moving water. 4. Inspect the Cell Vessel and verify the cell plates are fully covered by unplugging...

Salt & Swim Owner's Manual - Page 23

... used in or immediately adjacent to a pool or spa, war or acts of one (1) year. LIMITED WARRANTY (effective 12/01/12) Hayward warrants its Salt & Swim chlorination products to be the sole determinant of the date of installation of purchase or the nearest Hayward authorized warranty service center. Problems resulting from improper installation including installation...

Salt & Swim 3C Installation Quick Start Guide - Page 2

... Guide), plug linecord into the Cell Vessel as shown. The Salt & Swim should now display a solid INADEQUATE WATER FLOW and a solid STANDING BY LED. Salt & SwimTM 3C Installation Quick Start STEP 2: Determine where Cell Vessel will display a blinking INADEQUATE WATER FLOW LED and a solid STANDING BY LED. The entire Cutting Template must be installed vertically or horizontally and...