Hayward Salt & Swim Support Question
Hayward Salt & Swim Support Question
Find answers below for this question about Hayward Salt & Swim.Need a Hayward Salt & Swim manual? We have 3 online manuals for this item!
Question posted by haufbraudrinker on June 10th, 2014
Inadequate Water Flow Light Blinking
I have a problem with my Salt and swim I just installed after the calabration the Inadequate Water Flow light won't stop blinking. Pump is putting plenty of water back into the pool. Don't know what is wrong. I recycled the test at least 5 times.
Current Answers
Related Hayward Salt & Swim Manual Pages
Salt & Swim Owner's Manual - Page 1
092463 RevA
Salt & SwimTM
Chlorine Generator for Inground Swimming Pools up to 25,000 gallons
Owner's Manual
Contents
Introduction 1 Installation 2-8 Operation 12-14 Troubleshooting........15 Warranty 21 DIY-12 DIY-6
Hayward Pool Product 620 Division Street, Elizabeth, NJ 07207
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Salt & Swim Owner's Manual - Page 2
...RISK OF DROWNING FROM HAIR AND
BODY ENTRAPMENT, INSTALL A SUITABLY RATED SUCTION
GUARD TO MATCH THE MAXIMUM FLOW RATE MARKED. When installing and using this product unless they are provided ...shock, connect the local common bonding grid in the area of a pool or spa/
hot tub. To reduce the risk of electric shock, install at all times.
•
WARNING -
per conductor not smaller than ...
Salt & Swim Owner's Manual - Page 3
... that is offered in a pool or spa using natural stone for coping or for one pool season. The Salt & Swim requires a low concentration of chlorination required to properly sanitize a pool varies due to last for immediately adjacent patios/ decking, a qualified stone installation specialist should be used around a saline pool with fresh water. It automatically sanitizes your chlorinator...
Salt & Swim Owner's Manual - Page 4
... operating the Salt & Swim .
Installation
Remove power to the pool filter pump before you intend to operate the Salt and Swim. Some adjustments to your pool water, follow the instructions on the Installation Quick Start Guide. Waterproof GFCI Outlet
3 Feet
15 Feet
FILTER PUMP
Optional Vertical Installation
FROM POOL
TO POOL
Preparing Pool Water
To prepare the pool water for more...
Salt & Swim Owner's Manual - Page 5
... Salt & Swim inside the box), it is designed to the pool.
The
Cell Vessel must be installed on a flat surface with the cables facing downward. All pool equipment should be installed...., and within 3 feet of the return
piping just before the water returns to install in either 1½" or 2" PVC pool plumbing. The Control Box is installed.
3 Screw in top fasteners leaving 1/8" space ...
Salt & Swim Owner's Manual - Page 9
...INADEQUATE WATER FLOW and a solid STANDING BY LED. The Flow Switch Calibration procedure will run the pump for information on your pool. The Flow Switch Calibration procedure is properly initialized. You can take up , or when a new Cell is installed, the Salt & Swim will require the user to ensure that full flow is initialized, the Salt & Swim will display a blinking INADEQUATE WATER...
Salt & Swim Owner's Manual - Page 10
...may occur. Saturation index
The saturation index (Si) relates to use pool water test strips and refer to determine Ti, Ci,and
Ai from your Salt & Swim chlorine generator. Si = pH + Ti + Ci + Ai -... the saturation index. Have your water tested or use : Measure pool pH, temperature, calcium hardness,
and total alkalinity. Insert values of Pool and Spa Professionals (APSP). If the Si...
Salt & Swim Owner's Manual - Page 11
... common food quality or water softener salt and is usually available in low chlorine production.
Turn the circulating pump on and add salt directly into the pool. Salt Level
Use the chart on page 10 to determine how much stabilizer must be added to reach the recommended levels. A high salt level can cause the Salt & Swim to shutdown and...
Salt & Swim Owner's Manual - Page 12
POUNDS and (Kg) of SALT NEEDED FOR 3200PPM
Current salt
Gallons and (Liters) of Pool Water
level
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 25,000
ppm (30,000) (37,500) (...
Salt & Swim Owner's Manual - Page 14
... indicate the relative amount of this is actively generating chlorine. Illuminates when there is SUPER CHLORINATING. Blinks when performing the Flow Switch Calibration procedure. This electronically "super chlorinates" (boosts chlorine
generation output) the water for the filter pump to the Troubleshooting section of chlorine being generated. Refer to turn on during this LED indicator...
Salt & Swim Owner's Manual - Page 15
...amount of chlorine that you may have an ON/OFF switch . The Salt & Swim stops generating when the pool water temperature drops below 50ºF. NOTE: After the ideal DAILY CHLORINE OUTPUT ...finished, the Salt and & Swim will be lit. There should be closed. This is usually not a problem because bacteria and algae stop growing at the peak of salt in the pool The filter pump timer should...
Salt & Swim Owner's Manual - Page 16
... scale off of freezing temperatures, be sure to drain all water from the pump before any winter weather and should not be found on until the pool water chemistry has been brought to remove the Cell. This information can be removed. Maintaining the Salt & Swim System
The replaceable Cell uses the same electronic self cleaning technology...
Salt & Swim Owner's Manual - Page 17
... blinking The Salt & Swim has shut down the Salt & Swim. 4. The system will show the operation status as well as alert the user to identify and correct problems that the filter pump is detected, the GFCI may have occurred. Note: This condition can sometimes happen if the pool/spa temperature is already high and the heater is too low - INADEQUATE WATER FLOW...
Salt & Swim Owner's Manual - Page 18
... the Cell for Cell cleaning. 8. Refer to recommended levels. - PROBLEM DETECTED LED illuminated AND MAX LED blinking There is free to the diagram below . Adjust salt to the table for their corresponding errors.
16
Flow Switch
5. If the Cell is blinking The Salt & Swim may be too low. PROBLEM DETECTED LED illuminated AND a DAILY CHLORINE OUTPUT
LED is...
Salt & Swim Owner's Manual - Page 19
... dirty, follow the Cell cleaning procedure. 3. LED BLINKING
POSSIBLE ACTIONS
MIN LED or
LED 2
1. LED 4
LED 5 or
LED 6
1. Recycle power to the Salt & Swim by unplugging the linecord for two minutes and then plugging it back in . 2. Water Flow 2. Contact Hayward Technical Service. Recycle power to the Salt & Swim by unplugging the linecord for two minutes and...
Salt & Swim Owner's Manual - Page 23
...Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations, fire, flood, lightning, freezing, external water, degradation of natural stone used in or immediately adjacent to install, operate or maintain the product(s) in accordance with the recommendations in the owners manual(s). 4. LIMITED WARRANTY (effective 03/01/12) Hayward warrants its Salt & Swim...
Salt & Swim Installation Quick Start Guide - Page 1
...salt in the Overview.
WWW.HAYWARD.COM 855-429-9274
Turn Over Use the included Mounting Template to help locate the mounting holes and fasten the Control Box to install... the Cell Vessel as shown in your pool (see Chemistry Quickstart Guide)
Installation Preparation Read this entire Quickstart Guide Remove power to filter pump Drain water from the pool. Pool plumbing is 1½" or 2" PVC ...
Salt & Swim Installation Quick Start Guide - Page 2
... pump for at the installation location. The Salt & Swim should now display a solid INADEQUATE WATER FLOW and a solid STANDING BY LED. You can be the very last component installed in the system) and run the pump for 5 minutes or until all 10 cutouts. STEP 3: Install Nut Assembly
Follow the procedure below to the Cell before the water returns back to the pool...
Salt & Swim Chemistry Quick Start Guide - Page 1
... Baking Soda (Sodium Bicarbonate 100%). RECOMMENDED LEVEL: 2700 - 3400 ppm (3200 ppm ideal)
After testing salt, refer to Table 1 to determine how much salt must be added directly to the pool with the pool pump on the bottom of water in meters)
Length x Width x Average Depth x 1000
Diameter x Diameter x Average Depth x 785
Length x Width x Average Depth...
Salt & Swim Chemistry Quick Start Guide - Page 2
Table 1
POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM
Current salt
Gallons and (Liters) of Pool/Spa water
level
12,000 14,000 16,000 18,000 20,000...500)
1
(0)
2
(0.06)
3.2
(0.1)
4.2
(0.13)
5.2
(0.16)
6.2
(0.2)
7.2
(0.23)
8.4
(0.26)
9.4
(0.3)
10.4
(0.32)
Gallons and (Liters) of Pool Water
1,000 5,000 10,000 15,000 20,000 25,000 (3,750) (19,000) (38,000) (57,000) (75,000) (95,000)
2.5
(0.08)
5
...
Similar Questions
Salt And Swim Inadequate Water Flow
i have gotten the inadequate water flow mesage on the led indicator and followed all steps listed in...
i have gotten the inadequate water flow mesage on the led indicator and followed all steps listed in...
(Posted by mcarroll713 8 years ago)
The Swim Pure Is Showing All Kinds Of Numbers & Blinking Lights! Help!
(Posted by Ckesunshine 9 years ago)
Standy Light Blinking And Not Generating Chlorine
My stanby light just began a constant blinking and no chlroine is being generated. If I set the syst...
My stanby light just began a constant blinking and no chlroine is being generated. If I set the syst...
(Posted by plugabug 11 years ago)