Hayward Power-Flo II Support Question
Hayward Power-Flo II Support Question
Find answers below for this question about Hayward Power-Flo II.Need a Hayward Power-Flo II manual? We have 1 online manual for this item!
Question posted by missingoaksranch on May 20th, 2012
Filters Fine. Trips Breaker On Backwash & Wont Run Vacuum? Why? Thanks
The person who posted this question about this Hayward product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hayward Power-Flo II Manual Pages
Model: ALL - Page 1
...MANUAL
INSTALLATION, OPERATION, & PARTS
Power-Flo LX™ / Power-Flo II™ Pump Series
The Hayward® Power-Flo LX™ and Power-Flo II™ Pump Series are UL-...highly recommend a qualified professional install and service this product. SAVE THIS INSTRUCTION MANUAL
HAYWARD POOL PRODUCTS, INC. Corporate Headquarters: 620 Division Street Elizabeth, NJ 07207
U.S.A: 1 Hayward ...
Model: ALL - Page 2
... parts of swimming pool, spa, or hot tub, and to all times. Connect a No. 8 AWG (8.4 mm²) solid copper bonding wire to the pressure wire connector provided on this
product.
Power-Flo LX™ / Power-Flo II™ Pump Series
PRODUCT REGISTRATION
(Retain For Your Records)
DATE OF INSTALLATION
INITIAL PRESSURE GAUGE READING (CLEAN FILTER
PUMP MODEL HORSEPOWER...
Model: ALL - Page 3
...filtration system use the pool or
spa if a drain cover is equipped with a cord complying with all applicable local building codes. Power-Flo LX™ / Power-Flo II™ Pump Series ...your pump is damaged, cracked, missing, or not securely attached. WARNING - Pumps, filters, and other equipment.
Never use provided air relief valve to the manufacturer's recommendations....
Model: ALL - Page 4
... to prevent leakage.
All plastic fittings must be installed below the pool water line (see Figure to four (4) feet above the pool water line. Use care when using Teflon tape as possible. &#...if a long run pipe AWAY from pump. NEVER use .
For pipe larger than port, use 1-1/2" PVC pipe or reinforced hose.
Install pump on pipe or hose joints. Self-priming Power-Flo II™ pumps ...
Model: ALL - Page 5
... 90% or more than 110% of swimming pool, spa, or hot tub. Permanently ground motor. Use...breaker sizes. (NOTE: If unsure how to a gas supply line. If GFCI trips and won't reset, consult electrician to electrical power supply. Insure that the electrical supply available agrees with the motor's voltage, phase, and cycle, and that could cause an air trap. Power-Flo LX™ / Power-Flo II...
Model: ALL - Page 6
... hand only (no wrenches) ¼ turn clockwise to pool/spa system directly in suction and outlet pipes. 3. WARNING -
To do not use conduit when wiring motor, be sure pressure has been
released before starting system. ƒ Release all valves before proceeding. 2. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions (cont.)
Electrical (cont...
Model: ALL - Page 7
...Inspect all intake and output fittings and piping. 5. Prime pump according to the pool. 2. Power-Flo LX™ / Power-Flo II™ Pump Series
Storage/Winterization
WARNING - Do NOT use
extension cords. Refill pool to anyone nearby. Install all electrical wiring for swimming pool pump installation.
To avoid condensation/corrosion problems, do not permit children to motor
before...
Model: ALL - Page 8
...the impeller. 5. Troubleshooting
Motor Will NOT Start - Improper or loose wiring connections; tripped circuit breakers, GFCI's, or blown fuses. 2. Manually check rotation of motor shaft for free movement...Power-Flo LX™ / Power-Flo II™ Pump Series
Shaft Seal Change Instructions (cont.)
Exercise extreme care in handling both the skimmer outlet port and return port to pool...
Model: ALL - Page 9
... up or binded on skimmer wall.
3. iv. Cartridge filters - Motor bearings noisy from return fittings). Pump Won't Prime
1. Make sure all suction and discharge valves are tight. b. How to clean.
See "Shaft Seal Change Instructions" in pool, and
unrestricted discharge return lines. Power-Flo LX™ / Power-Flo II™ Pump Series
Troubleshooting (cont.)
Motor Hums, But...
Model: ALL - Page 10
...
16 Drain Plug with Gasket
SPX1700FG
SPX1700FG
17 C-Clip
SPX1515C
SPX1515C
* To order 2-speed motor, change "1" in suffix of model number to Part No.
Power-Flo LX™ / Power-Flo II™ Pump Series
Replacement Parts
Parts Diagram
Parts Listing
Ref. on Original Equipment
Refer to Part No. Motor (for SW1585X20) - 2 HP
---- SPX1515Z1E
Motor (for...
Model: ALL - Page 11
...and you . warrants its products free from Hayward:
□ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater Hayward ...written authorization of Hayward Pool Products, Inc. For further Hayward dealer or service center information, contact Hayward customer service department. Power-Flo LX™ / Power-Flo II™ Pump Series...
Similar Questions
Filter Button Lights Up But Wont Turn On The Filter.
Why doesn't my filter button turn on my pool when I press it. It only turns on when I press the Aux ...
Why doesn't my filter button turn on my pool when I press it. It only turns on when I press the Aux ...
(Posted by tereasajjt1 5 years ago)
Hayward Sand Filter S220t Won't Backwash
(Posted by Terrykmkrazybou 9 years ago)
Pump Tripping Breaker After Skim Overflowed From Heavy Rain
(Posted by jdoolin99031 9 years ago)
1 Hp Hayward Sp5500z2 Pool Pump Power Flo Matrix Motor Wont Start
(Posted by Rvesjeevi 10 years ago)
