Hayward Pro Series Top-Mount Support Question
Hayward Pro Series Top-Mount Support Question
Find answers below for this question about Hayward Pro Series Top-Mount.Need a Hayward Pro Series Top-Mount manual? We have 4 online manuals for this item!
Question posted by Terrykmkrazybou on September 10th, 2014
Hayward Sand Filter S220t Won't Backwash
The person who posted this question about this Hayward product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hayward Pro Series Top-Mount Manual Pages
Models: S220T S244T - Page 1
... THIS INSTRUCTION MANUAL
Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm)
HAYWARD POOL PRODUCTS, INC.
620 Division Street Elizabeth, NJ 07207 Tel: 908-351-5400 WWW.HAYWARDPOOL.COM
OWNER'S MANUAL
INSTALLATION, OPERATION & PARTS
IS210T-06 Rev. A
MODELS S180T, S210T, S220T, S244T PRO™ SERIES HIGH-RATE SAND FILTERS
Basic safety precautions should always be alert to...
Models: S220T S244T - Page 2
...pool/spa from near point. A negative pressure applied directly to remove pressure test plugs and/or plugs used as means of 8
MODEL S180T, S210T, S220T...open position.
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Suction in suction outlets ...applicable. Failure to a large portion of
pump and/or filter components. WARNING - WARNING - A negative pressure applied to ...
Models: S220T S244T - Page 3
... and maintained according to instructions, your pool dealer. a. Insert Filter Control Valve (with screwdriver handle to help seat valve flange clamp.
5. After a period of 8
MODEL S180T, S210T, S220T, S244T
IS210T-06 Rev A
WARNING -
Filter sand media is securely in place on electrical connections. Your Hayward Pro Series high-rate sand filter is securely in place in bottom...
Models: S220T S244T - Page 4
... or less depending on valve top between any impurities or fine sand particles in FILTER position (not BACKWASH) to prevent clogging of 7.2 to RINSE position. Stop pump, set valve to 7.6.
To properly sanitize your pool size and usage. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 4 of two factors-adequate filtration and proper...
Models: S220T S244T - Page 5
...USE ONLY HAYWARD GENUINE REPLACEMENT PARTS PARTS Models S180T, S210T, S220T, S244T
REF NO 1 2 3 4 5
PART NO.
Page 5 of 8
MODEL S180T, S210T, S220T, S244T
IS210T-06 Rev A
MODEL NUMBER
S180T S210T S220T S244T
EFFECTIVE...Flange Clamp Sand Shield -2004 Corrugated Design Folding Lateral Assy S180T Folding Lateral Assy S210T Folding Lateral Assy S220T Folding Lateral Assy S244T Filter tank Assy...
Models: S220T S244T - Page 6
... & refill pool with water that has not been treated with Cyanuric Acid. Operate filter for debris.
2. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 6 of sand if necessary).
Check skimmer and pump strainer baskets for longer periods.
4. SHORT FILTER CYCLES
1. Check surface of filter sand for crusting or caking (remove 1 " of 8
MODEL S180T, S210T, S220T, S240T...
Models: S220T S244T - Page 7
... by others.
To original purchasers of this equipment, Hayward Pool Products, Inc.
To original purchasers of purchase. Filters which fail or become defective during the warranty period,...a period of ONE (1) year from the date of 8
MODEL S180T, S210T, S220T, S240T
IS210T-06 Rev A
HAYWARD® LIMITED WARRANTY
This equipment was inspected before shipment from state to state.
...
Model: S270T - Page 1
SAVE THIS INSTRUCTION MANUAL
Use only High Rate Sand No. ½ Silica Sand (.45mm - .55mm)
HAYWARD POOL PRODUCTS, INC.
620 Division Street Elizabeth, NJ 07207 Tel: ..., death or major property damage and if
ignored presents a potential hazard. B
MODEL S270T PRO™ SERIES HIGH-RATE SAND FILTER
Basic safety precautions should always be alert to hazards. This is the safety-alert symbol. ...
Model: S270T - Page 2
... winterization of the pool/spa from near point to be in such locations and distances to a large portion of a suction outlet cover resulting in open filter manual air relief valve... described above .
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Suction Entrapment Hazard.
WARNING - Pool and spa water circulation systems operate under hazardous pressure during pump...
Model: S270T - Page 3
... Figure A.)
d. NOTE: Check to motor before loading with ease of the filter. d. Your Hayward Pro Series high-rate sand filter is loaded through your pool dealer.
The pool water, which contains suspended dirt particles, is pumped through the top opening ). The cleaned pool water is automatically directed by your piping system and is returned from the bottom of the...
Model: S270T - Page 4
... or an out of balance pH level will vary from backwashing is a large amount of filter sand media is in FILTER position (not BACKWASH) to BACKWASH. Be sure correct amount of plaster dust or debris-start -up of Hayward Pool Products, Inc. Check system and filter for continuous operation.
When filter pressure gauge rises 8-10 PSI (0.55-0.69 BAR) above...
Model: S270T - Page 6
...HAYWARD GENUINE REPLACEMENT PARTS Be sure flow rate through filter is set on "Filter" position. chlorine will naturally dissipate
CHLORINE STABILIZER (Cyanuric Acid)
40 to pool).
4. partially drain & refill pool...required).
3.
Check surface of filter sand for debris.
2. Check for longer periods.
4. POOL WATER WON'T CLEAR UP 1. Operate filter for restrictions in intake and ...
Model: S310T - Page 1
... should be installed, not more than 6
feet above pool water level, on a level concrete slab, very firm ground, or equivalent, as the permanent dirt removing media. IS310T-99
MODEL S310T
Your Hayward Pro Series high-rate sand filter is a high performance, totally corrosion-proof filter that blends superior flow characteristics and features with only the least attention...
Model: S310T - Page 3
.... Once water flow is clean. (It will vary from the pool water, the accumulation in the filter will cause the pressure to rise and flow to remove any impurities or fine sand
particles in the sand media. 4. The initial backwashing of filter sand, as required. 6. Adjust pool suction and return valves to do so could cause severe personal...
Model: S310T - Page 4
... strainer baskets for longer periods.
4. Backwash filter.
POOL WATER WON'T CLEAR UP
1. Check chlorine, pH and total alkalinity levels and adjust as required).
3. Be sure flow rate through filter is a combination of 7.2 to properly clean the pool water. POOL CHEMISTRY GUIDELINES
SUGGESTED POOL CHEMISTRY LEVELS
pH
7.2 to 7.6
ACTION REQUIRED TO CORRECT POOL CHEMISTRY
TO RAISE
TO LOWER...
Models: S310T2 S360T2 - Page 1
...and if ignored presents a potential hazard.
B
MODELS S310T2, S360T2, PRO™ SERIES HIGH-RATE SAND FILTERS
Basic safety precautions should always be alert to follow instructions can cause ...PARTS
IS310T2-06 Rev.
SAVE THIS INSTRUCTION MANUAL
Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm)
HAYWARD POOL PRODUCTS, INC.
620 Division Street Elizabeth, NJ 07207 Tel: 908-351...
Models: S310T2 S360T2 - Page 2
... ten years or if found to electrical power supply. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
o In addition two or more than 40 PSI.
WARNING - WARNING - Body Suction Entrapment- CAUTION - Before servicing pool and spa circulation system, the filter's manual air relief valve must be caught in a mechanical bind or swelling of...
Models: S310T2 S360T2 - Page 3
...Hayward Pro Series high-rate sand filter is a high performance, totally corrosion-proof filter that it is securely in place in opening marked RETURN and complete other necessary plumbing connections, suction lines to pool...directed to the bottom of the filter tank, through the control valve and back to instructions, your filter. Once the filter is backwashed (cleaned) of gauge. To ...
Models: S310T2 S360T2 - Page 4
... make it difficult for most swimming pools. Leave cap off flow from backwashing is designed for about 1/2 to achieve desired flow.
No returns may be made and are open), allowing the filter tank to filter. Pure, clear swimming pool water is in the water. Be sure correct amount of filter sand media is a combination of 8
MODEL S310T2...
Models: S310T2 S360T2 - Page 6
... ONLY HAYWARD GENUINE REPLACEMENT PARTS Check for algae in intake line (indicated by bubbles returning to 70 ppm Add Stabilizer
Dilution - Check surface of filter sand for ...intake and discharge lines.
3. partially drain & refill pool with water that has not been treated with Cyanuric Acid. Backwash filter. SHORT FILTER CYCLES
1. chlorine will naturally dissipate
CHLORINE (STABILIZED)...
Similar Questions
Sand Filter
How do you remove the laterals from a 244S Hayward side mount sand filter?
How do you remove the laterals from a 244S Hayward side mount sand filter?
(Posted by scoody1016 7 years ago)
Do You Need To Change The Sand In A Hayward Sand Filter Model S310t?
(Posted by icanallen 9 years ago)
How To Clean My Hayward Pro Series Model Number S-166t Sand Filter
(Posted by funngia 10 years ago)
Swimming Pool Dome Sand Filter/how Much Sand Is Needed
(Posted by jespradap 10 years ago)
Sand Amount Replacement For A Hayward S310t
is 500 lbs of sand media corrrect
is 500 lbs of sand media corrrect
(Posted by deanbackos 10 years ago)