Home » Genie » Garage Door Openers » Genie SilentMax 1000

Genie SilentMax 1000 Support Question

Find answers below for this question about Genie SilentMax 1000.
Need a Genie SilentMax 1000 manual? We have 1 online manual for this item!

Genie Overview Questions Manuals Reviews Videos Research

Question posted by Preete on July 23rd, 2020

Overhead Motor Has Red Light On. Will Not Open Or Close

please guide how can we shut the red light

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by techyagent on July 23rd, 2020 10:09 PM

This answer was accepted by the poster of the original question.

techyagent

Member since:
June 17th, 2014

Points: 4,799,790

1,070
points

When the infra-red sensors are malfunctioning, usually one of the sensor lights will be blinking. The problem is either due to a blocked path between the sensors, dirty eyes, loose wires at the sensors or at the motor head, or just bad sensors. The transmitters (remotes) will not work to close the garage door.

Please check this link below:-

https://www.geniedoor.com/product-tag/infra-red-sensors/

Thanks

Techygirl

Answer #2: Posted by Darknight586 on July 24th, 2020 1:53 AM

Darknight586

Member since:
July 18th, 2020

Points: 6,100

110
points

Follow these steps to reset red light

Doorr Must Be in Down Position.
Pull the Emergency Release Cord. ...
Manually Move the Garage Door and Return to Down Position.
Pull the Emergency Release Cord Toward the Door.
Re-connect the Trolley to the Opener Carriage

Related Genie SilentMax 1000 Manual Pages

Owner's Manual - Page 1

.... DO NOT RETURN to close door. Use this opener only with residential sectional or one -piece or sectional door. For use only with a one piece overhead garage doors. Car2U is a registered ... 38209501773 GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200...

Owner's Manual - Page 2

... Safety 4 Opener 4 R4equired5Progra6mming Introduction 5 Overview of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits...? If transmitters are to Door Bracket 15 M7aintena8nce an9d Adjustments Maintenance Safety 16 Regular Maintenance 16 Corrective Maintenance 17 Adjustment Guides 18 W8iring D9iagram 20 T9roubleshooting...

Owner's Manual - Page 3

...WARNING indicates a potentially hazardous situation which, if NOT avoided, could cause severe injury. Opener must be followed or important considerations. This is the safety alert symbol. This symbol ... CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are NOT pinched or near moving parts. Since moving objects, springs under high tension and electric motors. When replacing cover, make ...

Owner's Manual - Page 4

...3.When the garage door is closing, if Safe-T-Beam® is detected for safer evening exits and entries. SmartSet™ Electronic Programming Easily adjust the programming to reduce opening . Turns ON when door is installed improperly, press and hold the wall console "open position if anything passes through the garage. Lights will not allow manual opening and closing door within two...

Owner's Manual - Page 5

.... Speed Control refers to how fast or slow your opener opens and closes your particular door and is used to set how far your garage door opener for minor adjustments under certain circumstances. 4. This function does NOT require programming. This program does not require manually initiated changes. The LED lights indicate status or a function change by illuminating ON...

Owner's Manual - Page 6

...Closing Garage Door (Down Limits) 1 Lift the door open by hand until the shuttle/bullet engages the carriage on the rail. 4 Press and hold the down arrow button (-) for correct wiring or the Sure-Lock switch may be engaged to the opener... setting limits confirm wall console red indicator light (or backlight) is fully closed on the Powerhead, you see two solid red or flashing LEDs on floor,...

Owner's Manual - Page 7

... light comes on blue (round LED remains off). BOTH DOOR LIMITS ARE NOW PROGRAMMED. 7 7/13/12 10 17 AM PROGRAM SET - 3 Required Programming 5 Press and release the Program Set button (both LEDs flash blue and go off ). PROGRAM PROGRAM SET - Watch carriage as it approaches the power head to avoid contact with garage door closed...

Owner's Manual - Page 8

...closes door from inside garage. Open/Close Button Use this button is detected. When Sure-Lock™ is pressed again or a door action has been completed. UNLOCK allows controls to open or close door. Each wall console has three buttons. Note: Constant button pressure in the CLOSE mode will override STB fault in the powerhead and close garage door. Powerhead lighting will display Red...

Owner's Manual - Page 9

.... 9 NOTE: Force or Speed controls DO NOT require programming. Red LED lights on the Wall Console. Contact Reverse Adjustment If the door stops before it should stop and reverse direction within 2 seconds to set force limits. Repeat this manual (pages 18-19). 10 Open and close your garage door. FORCE AND SPEED CONTROL ARE NOW SET. 3 Required...

Owner's Manual - Page 11

...program the same Remote for three door openers. BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR IS READY TO USE! The Remote button is now programmed. Each Remote can be programmed for other garage door openers, repeat the steps above using ... and release the same button on the remote (the door should open or close). G999-393 Manual-ScrewBeltChain-EN indd 11 11 7/13/12 10 17 AM

Owner's Manual - Page 13

... BE reprogrammed as shown on the Powerhead and hold 2 seconds, round LED comes ON. Your opener will no longer recognize any signal received from the Powerhead memory will not activate the door opener. NOTE: The garage door opener will not activate the door opener. NOTE: When the remote is cleared, press a remote button that the memory is pressed...

Owner's Manual - Page 14

...preset to be opened . The light lens may need...RED and GREEN LEDs on the Remote turn ON). If your older Genie® door opener. NOTE: Choose the Genie® Remote using Intellicode® 1 button for this unit can operate other (Intellicode® 1) models of opener. Press and hold the button for operation with this Intellicode® 1 model of Genie® garage door openers...

Owner's Manual - Page 16

... should move very slowly. - Use caution when using this release with the door open position. See your door springs serviced. • Close the door. (continued next page) G999-393 Manual-ScrewBeltChain-EN indd 16 7/13/12 10 17 AM SAVE THESE INSTRUCTIONS WARNING • Garage door hardware (springs, cables, brackets, pulleys, etc.) are under extreme pressure and...

Owner's Manual - Page 17

... CFL's may also be used. - Reset Open/Close Travel Limit Performing all eleven (11) Limits/Force setting steps (see pages 6-8) erases previous Limits/Force settings. Note: The opener will re-attach itself to door opener. • Test light operation. Screw Drive Opener Belt/Chain Drive Opener Disengaged Engaged Disengaged Engaged - To disengage bullet from carriage...

Owner's Manual - Page 18

... either until you reach the desired setting. 5 Press and release. PROGRAM SET LED Indication/Result RED OFF BLUE OFF Flashes 3 Times The Current UP FORCE SETTING will display. Force Settings Force settings are : 1. 6 Maintenance and Adjustments Adjustment Guides CAUTION Door closing . 3. Both LEDs turn BLUE then OFF BLUE confirms both up , but STOP before...

Owner's Manual - Page 19

... or until you reach the desired setting. 7 Press and release. Sun Red Green LED LED One Door Garage 19 G999-393 Manual-ScrewBeltChain-EN indd 19 7/13/12 10 17 AM LOCKS IN CLOSING SETTING. PROGRAM SET 6 Press either until both the Open and Close directions, to increase speed. LED indicator colors: Speed Level High Medium...

Owner's Manual - Page 21

..., - See pages 6-7. • Check if Safe-T-Beam® Red LED is flashing. • Check Safe-T-Beam® system for beam obstruction or misalignment of lenses. • Check garage door for binding. • If an operational problem exists, and opener will not close, the opener can cut wires. OR Door will only run from wall console. • Check...

Owner's Manual - Page 22

... . Thermal cutout Program remote using instructions on a one -piece door is in good repair. Check alignment of door. Remove obstruction. WHAT TO DO • Be sure all door fasteners are tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is lowest speed setting. • If carriage travel...

Owner's Manual - Page 23

..., SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ...or damaged parts from the date of purchase: SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, MOTOR/GEARBOX- Seller warrants the motor for a period of FIVE (5) YEARS CORE UNIT...

Owner's Manual - Page 24

...garage door close? can open door without remote • Lighted keypad with Revolution Series 1500, 1200 and 1000 Models) • Sleek and compact design • Beeps and flashes green when garage door closes. Garage Door Opener Accessories Looking for activation Upgrade with style Convenience, Security All in addition to door - Gives warning tone and flashes red when garage door...