Genie PowerMax 1500 Support Question
Genie PowerMax 1500 Support Question
Find answers below for this question about Genie PowerMax 1500.Need a Genie PowerMax 1500 manual? We have 1 online manual for this item!
Question posted by A21607 on September 10th, 2013
Genie Powermax 1500 Learn Button
where is the learn button located?
Current Answers
Related Genie PowerMax 1500 Manual Pages
Owner's Manual - Page 1
... Technology Company. Car2U is a registered trademark of injury to persons or damage to the store. For use only with a one piece overhead garage doors. GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION...
Owner's Manual - Page 2
... 3 Important Safety Instructions 3 Infrared Protection Function 3
F3eatures
Safety 4 Opener 4
R4equired5Progra6mming
Introduction 5 Overview of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series II Wall Consoles with any other jurisdiction. Si...
Owner's Manual - Page 3
...wall button or console, in Death or Serious
Injury
Keep people clear of opening while door is the safety alert symbol. tion, call The Genie® Company or your nearest trained door system... USED IN THESE INSTRUCTIONS Garage doors are large, heavy objects that move with the door opener.
C) Away from all locks connected to be made by a trained door system technician, using proper...
Owner's Manual - Page 4
... independent light control buttons.
If you release the "open and close the
door, it will turn ON when motion is activated and automatically turns OFF 4 minutes later. SAFETY FEATURES
Safe-T-Beam® (STB) Non-Contact Reversing System Puts an invisible beam across the door opening speed to the full open /close . 3.When the garage door is closing, if...
Owner's Manual - Page 5
... program does not require manually initiated changes. move (open/ close) your particular door and does NOT require programming.
Speed Control refers to set how far your Genie garage door opener is used to enter and complete the setup programming. The following information will want to synch with the buttons, LED indicators and products used for you how...
Owner's Manual - Page 6
... Customer Service at 1-800-35GENIE or visit www.geniecompany.com
3 Release down arrow button (-) for correct wiring or the Sure-Lock switch may be engaged to carriage BEFORE...
G999-393 Manual-ScrewBeltChain-EN indd 6
7/13/12 10 17 AM
Closing Garage Door (Down Limits)
1 Lift the door open by hand until
garage door is fully closed on the Powerhead, you see two solid red or flashing LEDs...
Owner's Manual - Page 7
PROGRAM
SET
-
HOLD
Opening Garage Door (Up Limits)
NOTE: Beginning with powerhead. PROGRAM
SET
-
SET
HOLD 2 seconds
7 Release up arrow button (+) for
2 seconds until door
is programmed. PROGRAM
PROGRAM
- +
ET
G999-393 Manual-ScrewBeltChain-EN indd 7
The UP (open) limit is fully open, then release.
BOTH DOOR LIMITS ARE NOW PROGRAMMED.
7
7/13/12 10 17 AM
...
Owner's Manual - Page 8
... is completely closed .
Independent Light Control Button Use this button to open or close garage door.
LOCK disables controls
after
door is off ) to activate Sure-Lock™. • Press and release to open or close garage door. MODEL AC SR3 FCC ID: B8Q AC SR3 IC: 2 33A-CS 1D
THE GENIE COMPANY Residential Door Operator
120V. 60HZ. 5A
S/N:10XXXX XXXXXXX...
Owner's Manual - Page 9
... set themselves when you use the Wall Console to open and close your garage door using the Wall
Console Open/Close button.
13 Close the garage door using the Open/Close button
on the powerhead will clear the lights. Repeat the Setting the Down Limit steps 1-5 to open and close the garage door for the first time automatically sets the Force...
Owner's Manual - Page 11
... the ignition key in the car to Genie mode. G999-393 Manual-ScrewBeltChain-EN indd 11
11
7/13/12 10 17 AM 3 Required Programming
18 Press and release the same button on the remote
(the door should open or close).
BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR IS READY TO USE!
PROGRAM
IMPORTANT: Your HomeLink...
Owner's Manual - Page 12
Press the Program key . 3. Enter your PIN. 3.
Programming
Locate Your Opener's Programming Buttons and LED
Opener
4. Door opener will turn o . 5.
Resetting PIN
If you have forgotten your PIN or you must erase the old programming.
Opener LEDs will run. The door will automatically stop or start programming steps over.
Press Up/Down key again. Go back and ...
Owner's Manual - Page 13
... as shown on pages 9 and 12. T
- +
SET
HOLD 2 seconds
2 Release the Program Set button, round LED goes
off and the long LED flashes purple.
NOTE: The garage door opener will not activate the door opener. NOTE: When the remote is cleared, press
a remote button that was previously programmed to the Powerhead. G999-393 Manual-ScrewBeltChain-EN indd...
Owner's Manual - Page 14
... programmed to the Intellicode® 1.
3 Find the Learn Code Button and Learn Code Indicator LED
on the Remote turn the RED LED on the transmitter is preset to Intellicode® 1. NOTE: Choose the Genie® Remote using Intellicode® 1 button for this Intellicode® 1 model of Genie® garage door openers .The default Intellicode® 2 setting must be changed...
Owner's Manual - Page 16
... a 2" x 4" board laid flat) at : 1-800-35-GENIE or visit www.geniecompany.com
Important Safety Instructions
WARNING
TO REDUCE THE RISK OF SEVERE injury or death, READ AND FOLLOW ALL INSTRUCTIONS. 1.
Locate wall console within sight of travel, retest door opener. Verify wire routing from people
and objects until door is improperly balance or springs are...
Owner's Manual - Page 17
... Reconnect power to carriage, pull down and toward the opener. Note: The opener will re-attach itself to door opener. • Open powerhead light cover. • Remove light bulb(s). &#... replacing light cover, make sure wires are programmed.
To engage shuttle to door opener.
• Test light operation. Remote Battery Replacement Replace remote battery with greater...
Owner's Manual - Page 19
....
PROGRAM SET
4 Press either until both the Open and Close directions, to increase speed. FLASH BLUE
FLASH BLUE
SPEED SETTINGS DONE
Locating Safe-T-Beam Pairs:
Source (Red LED) and Sensor (Green LED)
Sun
Red Green
LED
LED
One Door Garage
Green LED
Red Red LED LED
Two Door Garage
Green LED
Green
Red Red
Green Green...
Owner's Manual - Page 21
... battery with the garage door hardware or springs, contact
The Genie Company at garage door.
• Replace battery. DO NOT RETURN to do
Opener does NOT run closed...garage door for interference from wall console.
• Check power source. -
8 Troubleshooting
OPERATION
Need help or have questions? Door will not close as follows: Press
and hold the wall console button until door...
Owner's Manual - Page 22
... .
WHAT TO DO
• Be sure all door fasteners are tight. • Be sure garage door is in . Remove obstruction, recheck unit. 8 Troubleshooting
OPERATION (continued)
PROBLEM Noisy operation.
Door may need professional repair/adjustment. • Is this opener installed on page 14.
Contact a trained door system technician. Program error. Unplug unit, wait 5 seconds...
Owner's Manual - Page 23
.../1200
LIMITED WARRANTY
GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("Product"), subject to all of the terms...
Owner's Manual - Page 24
...; Large, easy to other retail/commercial locations nationwide. Leading-Edge Technology
Did your garage door close properly
• Network Adapter required
Easy operation at Home Improvement outlets and other remotes or wall buttons
Check out NEW ACCESSORIES and PRODUCTS;
Closed Confirm™ Wireless Remote
(Works with all Genie garage door openers
manufactured from 1993 to the present...
Similar Questions
My Promax 1500 Garage Door Opener Not Working.3 Lights Flashing On Unit.
(Posted by cwestsupra 9 years ago)
Garage Door Opener Not Working
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
(Posted by scanty5 9 years ago)
Where Is The Reset Button On Genie Garage Door Opener Powermax 1500
(Posted by jpIJac 9 years ago)
Where Is The Learn Button On My Genie Silentmax 1000 Garage Door Opener
(Posted by xEPmoor 9 years ago)
Where Is The Learn Code Button Situated On The 3060l-07 Genie Garage Door Opener
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
(Posted by katiaella 10 years ago)