Home » Genie » Garage Door Openers » Genie IntelliG 1200

Genie IntelliG 1200 Support Question

Find answers below for this question about Genie IntelliG 1200.
Need a Genie IntelliG 1200 manual? We have 1 online manual for this item!

Genie Overview Questions Manuals Reviews Videos Research

Question posted by erickillgore on May 22nd, 2022

Is There A Fuse In The Intellig 1200

Is there a fuse in the IntelliG 1200

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on May 22nd, 2022 9:53 PM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,621,300

1,100
points

Is there a fuse in my Genie garage door opener?

The Genie 34138A10F 10-amp replacement fuse from Garage Door Supply Company is for use with Genie Excelerator residential garage door openers. It's a plug-in fuse that plugs into Genie Excelerator garage door operator drive boards.

https://www.manualslib.com/products/Genie-Intellig-1200-2853311.html

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Genie IntelliG 1200 Manual Pages

Owner's Manual - Page 1

... of injury to persons or damage to property - Use this opener only with residential sectional or one -piece or sectional door. GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200 SCREW/BELT/CHAIN DRIVES OPERATION & MAINTENANCE MANUAL Includes INTELLICO®...

Owner's Manual - Page 2

...store. 9 S2afety Inf3ormatio4n Safety Notifications 3 Important Safety Instructions 3 Infrared Protection Function 3 F3eatures Safety 4 Opener 4 R4equired5Progra6mming Introduction 5 Overview of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series...

Owner's Manual - Page 3

...must be followed or important considerations. C) Away from all locks connected to the door before removing opener cover. When replacing cover, make sure wires are fastened, such as, wood ...Information OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, heavy objects that move with the help of springs under tension,...

Owner's Manual - Page 4

... buttons. Lights automatically turn OFF after 4 minutes of the door opener by a person or obstacle, the garage door will stop and reverse a closing movement, the door will turn ON when motion is activated and automatically turns OFF 4 minutes later. Wall Console Operates door opener from door opener. Contact your Genie® Professional Dealer for an Assembly/Installation...

Owner's Manual - Page 5

... program does not require manually initiated changes. The LED lights indicate status or a function change by illuminating ON, OFF, or ON FLASHING in the garage door opening and closing your garage door. Remote Programming synchronizes your remote control devices (remotes, wall console, and keypad) with the powerhead. Force Control refers to how much power is...

Owner's Manual - Page 6

...-ScrewBeltChain-EN indd 6 7/13/12 10 17 AM PROGRAM SET + NOTE: If shuttle/bullet has NOT been engaged to complete each step. Closing Garage Door (Down Limits) 1 Lift the door open by hand until the shuttle/bullet engages the carriage on the rail. 4 Press and hold the down arrow button (-) and the long LED...

Owner's Manual - Page 7

... Program Set button (both LEDs flash blue and go off ). PROGRAM SET - PROGRAM PROGRAM - + ET G999-393 Manual-ScrewBeltChain-EN indd 7 The UP (open , then release. HOLD Opening Garage Door (Up Limits) NOTE: Beginning with powerhead. PROGRAM SET - 9 Press and release the Program Set button (both LEDs flash blue and go off). SET HOLD...

Owner's Manual - Page 8

...Sure-Lock™ is detected. B/W - Note: Constant button pressure in the powerhead and close garage door. To powerhead Sure-Lock™ Button - Independent Light Control Button Controls door opener lights from inside garage. 8 Series III Wall Consoles with openers of the following wall consoles: Series II Wall Consoles with White Buttons Indicator Light Large...

Owner's Manual - Page 9

... 16-19. 9 NOTE: Force or Speed controls DO NOT require programming. When the door contacts the board, it does not reverse direction to fully open and close your garage door using the Wall Console Open/Close button. 13 Close the garage door using the Open/Close button on the powerhead will clear the lights. Contact Reverse Adjustment If...

Owner's Manual - Page 11

... READY TO USE! G999-393 Manual-ScrewBeltChain-EN indd 11 11 7/13/12 10 17 AM Each Remote can be programmed for other garage door openers, repeat the steps above using one of the other two Remote buttons. to connect to your Intellicode remote when it's searching SET - The Remote button ...

Owner's Manual - Page 12

...will automatically stop or start programming steps over. When the blinking stops, you must start the opener while the door is ready for 2 seconds. (The round LED turns blue and then goes o . ... Enter your PIN or you are still having trouble with the keypad, refer to slowly blink. Door opener will stay on the Powerhead indicates an error. To erase, follow the steps in "Setting Up...

Owner's Manual - Page 13

... Remotes and wireless Keypads. NOTE: Clearing Remotes from a missing Remote. Your opener will not activate the door opener. 4 Optional Programming Clearing Memory FOR Remotes 1 Press the Program Set button on...from the Powerhead memory will not activate the door opener. NOTE: The garage door opener will operate normally using the Wall Console. PROGRAM PROGRAM 4 To verify that was...

Owner's Manual - Page 14

.... This button is programmed to turn ON). NOTE: Choose the Genie® Remote using Intellicode® 1 button for this Intellicode® 1 model of Genie® garage door openers .The default Intellicode® 2 setting must be opened to access the Learn Code Button and Indicator LED. 4 Press the Learn Code Button (the LED on the...

Owner's Manual - Page 16

...ALL INSTRUCTIONS. 1. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR. 5. KEEP DOORS PROPERLY BALANCED. Have a trained door system technician make repairs to cables, spring assemblies, and other wall control can cause unexpected operation of the door and loss of any hardware, and DO NOT OPERATE garage door automatically or manually if door is completely closed , pull manual emergency release...

Owner's Manual - Page 17

... a ladder or step stool. • When replacing light cover, make sure wires are programmed. Disconnect power to door opener. • Test light operation. To disengage bullet from carriage, pull relaese handle down and toward the opener. 6 Maintenance and Adjustments REGULAR MAINTENANCE (continued) • Screw drive models: Verify shuttle release lever is in ENGAGED...

Owner's Manual - Page 19

... the direct sunlight side Multiple Garage Doors • NEVER position Safe-T-Beam modules where signals will cross. • Place the Source (Red LED) Safe-T-Beams on the criteria mentioned above , you may not have speed adjustments. BLUE BLUE OFF Flashes BLUE 3 Times Then the Current Speed setting for OPENING travel will display. SEE...

Owner's Manual - Page 21

8 Troubleshooting OPERATION Need help or have questions? If not, check fuse or circuit breaker. • If power is completely closed. .... See page 17. • Reposition door opener antenna. • Remote LED does not come ON with the garage door hardware or springs, contact The Genie Company at garage door. • Replace battery. Door starts up . no operation. • ...

Owner's Manual - Page 22

... programmed. Safe-T-Beam® physical obstruction. Door may need professional repair/adjustment. • Is this opener installed on page 14. Program error. Door component failure detected. 8 Troubleshooting OPERATION (continued) PROBLEM Noisy operation. WHAT TO DO • Be sure all door fasteners are tight. • Be sure garage door is in good repair. POWERHEAD LEDS...

Owner's Manual - Page 23

... d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("Product"), subject to Seller at purchaser's expense), Seller will be defective prior to removal or...

Owner's Manual - Page 24

... door openers manufactured from 1993 to the present • Operates up to three openers White Gray Tan Almond Color-Match These Covers to mount inside garage • Used in One Keyless Entry Pad • Wireless; Leading-Edge Technology Did your finger tips "retro" Replacement GenieMaster™ 3-Button Remote • Compatible with Revolution Series 1500, 1200...