GE JVB94SHSS Support Question
GE JVB94SHSS Support Question
Find answers below for this question about GE JVB94SHSS.Need a GE JVB94SHSS manual? We have 2 online manuals for this item!
Question posted by hibbardhubbard on July 15th, 2018
Downdraft Stuck In Up Position
Downdraft vent stuck in up position. When down will rise, but will not return down. Removed switch to test wiresDC Voltage between wires to switch is 0 VDC. When measured independently to electrical outlet ground they are +10VDC adn -14 VDC.When trying to measure voltage on wires, engine 'clicks' sometimes like it is engaging for a split second.Switch operates fine with Infinite Resistance normally. Going to 0 Ohms when depressed.
Current Answers
Related GE JVB94SHSS Manual Pages
Use and Care Manual - Page 1
... Units JVB67 and JVB98 11 Dimensions and Clearances . .7, 8 Ductwork 8, 13, 15 Electrical and Gas Location . . . .8 Installation Possibilities 9 Installing the Downdraft Vent System 10-17 Optional Kits 17 Power Supply 12 Raise/Lower Switch 16 Venting Options 14
Troubleshooting Tips 18
Consumer Support
Consumer Support 20 Warranty 19
Owner's Manual & Installation Instructions
JVB37...
Use and Care Manual - Page 2
...as duct under the hood, turn hood ON when cooking at ...switch power off at service panel and lock the service disconnecting means to prevent back drafting.
If you do not damage electrical wiring and other hidden utilities. PLEASE NOTE: The downdraft vent.... Heat oils slowly on .
2 I This unit must always be grounded.
I PVC sewer pipe can be allowed to the outdoors. READ ALL...
Use and Care Manual - Page 3
... the Install the Downdraft
blower motor or air vent mechanism. SERVICING
Be sure electrical power is off the burner.
NEVER PICK UP A FLAMING PAN-You may be necessary to remove the downdraft blower Disconnect power... IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
A. Do not use only. Make sure all fingers are available from the downdraft top when it
system in this...
Use and Care Manual - Page 4
... sure fingers are clear of the downdraft and cannot be lowered by pressing the raise/lower switch located at the top right side of the vent.
Use the selector switch to turn the blower ON, OFF or to change the blower speed. NOTE: There is lowered. The blower will rise. On some models, the Raise...
Use and Care Manual - Page 5
... soil.
it will mar the surface.
Use of the blower at LOW speed and using a mild detergent.
Grease Filters
The efficiency of the downdraft system. To remove: Pull the filters out by grasping them and pulling straight up.
Painted or Metal Surfaces
Clean greasy surfaces frequently, using the front surface unit.
Safety...
Use and Care Manual - Page 6
...for 36″ models only)
Pliers
Duct tape
Wire box (2) and screws (4)
Plastic strain relief (2)
Wire and white connector (1)
Jig saw
Ductwork to Consumer...Remove the shipping materials. Be sure to leave these instructions completely and carefully.
• IMPORTANT - This appliance must be used as a pad when changing or adjusting vent direction. Installation Instructions
Downdraft Vent...
Use and Care Manual - Page 8
... outside of the electrical outlet and gas (if used above cooktop.
COOKTOP ELECTRICAL AND GAS LOCATION
Plan the placement of the vent/cooktop cutout.
8 DUCTWORK
Prepare ductwork to vent to calculate equivalent length for a wall cap or roof cap. Installation Instructions
ADVANCE PLANNING
CLEARANCES
• Installation must conform with local codes.
• The downdraft system with...
Use and Care Manual - Page 10
... begin, measure and mark Dimension 3 to sides.
21⁄8″
32
81⁄2″
1
5
4
6
Planning Installation 30″ Electric and Gas Cooktops with Downdraft*
21...
23-1/8″ 23-1/8″ 23-3/8″ 23-3/4″
**Includes 1/8″ gap between cooktop and vent trim **Required to maintain UL or AGA approvals
Minimum Setback Cutout to Front Edge**
2-1/2″
2-1/2&#...
Use and Care Manual - Page 11
...8243;
Cooktop Surface Surface Depth Overall Depth with Downdraft Vents
1
2
3
4
Model No. Identify the cutout illustration for the cooktop model you begin, measure and mark Dimension 3 to Front Edge**
...32
81⁄2″
1
5
4
6
Planning Installation 36″ Electric and Gas Cooktops with Downdraft*
21″
23-1/8″
20-3/8″
22-1/2″
JP960S JP968S
JGP628...
Use and Care Manual - Page 12
... individual, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
Do not leave gas or electrical connections within reach of the cabinet wall where it may interfere with the downdraft plenum.
Installation Instructions
INSTALLING THE DOWNDRAFT VENT SYSTEM
POWER SUPPLY
This downdraft vent must operate from the same duplex outlet.
Gas...
Use and Care Manual - Page 14
Installation Instructions
INSTALLING THE DOWNDRAFT VENT SYSTEM
VENTING OPTIONS
Side-to-Side Adjustments The entire blower mounting plate can be changed to the left or right side. Loosen screws to the mounting plate assembly. Retain screws.
2 Remove the blower assembly, turn it over the discharge outlet.
• Mark the location and remove the assembly.
• Cut holes...
Use and Care Manual - Page 15
... to calculate your installation. See illustration. Attach brackets to slide screws on the bottom of cabinet
Secure the lower brackets to blower housing
Place the downdraft vent into the countertop cutout, against the back side. DO NOT USE flexible ducting.
• Always use appropriate roof or wall cap with self-tapping screws...
Use and Care Manual - Page 16
... and press into a tile surface, drill the hole between the switch cover, adjacent objects and cooktop/vent overlaps. Remove and drill holes according to cover any gaps. Connect Wire Lead to the electrical controls. E Coil the excess wire and position away from the unit before beginning switch installation. Failure to do so could result in personal injury or...
Use and Care Manual - Page 17
... a thickness gauge, align the cooktop so that there is no interference when air vent is raised and lowered. INSTALL THE COOKTOP
• With the downdraft in the "down" position, place the cooktop into a properly grounded receptacle. NOTE: Do not force the downdraft cover to ensure that there is a minimum uniform gap of 0.05″ (the...
Use and Care Manual - Page 18
...Problem Fan does not work
Vent does not rise
Possible Causes
The vent is not fully extended. What To Do • Press the Raise/Lower switch. • Slide it...Vent not plugged into an outlet. • Plug vent into a 120V power outlet.
Circuit breaker may be in . • Check all connections between the remote switch and vent body.
18
Remote switch not plugged in the OFF position...
Use and Care Manual - Page 19
...Staple your state's Attorney General. During this Limited Warranty.
I Replacement of the downdraft system which vary from state to replace the defective part. This warranty is needed... Failure of merchantability or fitness for a particular purpose, are responsible for providing adequate electrical, gas, exhausting and other than the intended purpose or used for service.
I ...
Use and Care Manual - Page 20
... can purchase it on our Website with all ages, sizes and capabilities. For details of GE's Universal Design applications, including kitchen design ideas for a wide range of the year! Caution must be referred to their homes (VISA, MasterCard and Discover cards are not satisfied with the service you are accepted). Schedule...
Quick Specs - Page 1
...Note: Telescopic downdraft vents are for ...downdraft and cooktop.
Listed by Underwriters Laboratories
For answers to dimension requirements. JVB94SH - Not approved for installation of motor and blower assembly on outside wall. Optional accessory may be ordered for further details. Refer to instructions packed with the following GE Profile™ and GE cooktops - 36" and 30" electric...
Quick Specs - Page 2
...Two different discharge directions are based on actual tests conducted by Underwriters Laboratories
For answers to 6" round...of floor joists, wall joists, wall studs, electrical wiring or plumbing for all duct pieces and transitions used... ft. 2 ft. 4 ft.
GE Profile™ 30" Telescopic Downdraft System
Venting Duct Information
DUCTWORK LENGTH AND DUCT FITTINGS
NOTE: Do not exceed 150...
Quick Specs - Page 3
...Specification Revised 5/09
220963 GE Profile™ 30" Telescopic Downdraft System
Features and Benefits
• Telescopic downdraft hood - OFF
LEFT
LO
• Removable grease filter - JVB94SH -
Durable filters can be removed for easy cleaning and maintenance.
• Model JVB94SHSS - Powerful 500 CFM performance removes smoke and vapors from the cooking area.
• Variable...
Similar Questions
Remove And Change Light Bulb On Ge Jvw5301 Range Hood
Page 9 says use a flathead screwdriver to remove ring but does not tell you how to do this. Push, pu...
Page 9 says use a flathead screwdriver to remove ring but does not tell you how to do this. Push, pu...
(Posted by ltindle 6 years ago)
Ge Jvx3300 Range Hood. How Do I Remove The Light Bulb Cover?
There's a little picture showing that you should use a screw driver, but nothing beyond that. I'm af...
There's a little picture showing that you should use a screw driver, but nothing beyond that. I'm af...
(Posted by Dontcallmehowie 6 years ago)
Vent Is Not Working
I have a GE profile range with a telescoping pop up vent. The vent no longer works not sure if its a...
I have a GE profile range with a telescoping pop up vent. The vent no longer works not sure if its a...
(Posted by valentinbernabe 11 years ago)
