GE JVB37HBB Support Question
GE JVB37HBB Support Question
Find answers below for this question about GE JVB37HBB.Need a GE JVB37HBB manual? We have 2 online manuals for this item!
Question posted by heightsroofing on December 17th, 2011
Re.i Own A Gejvb37 Downdraft Vent
how do I replace the switch
Current Answers
Related GE JVB37HBB Manual Pages
Use and Care Manual - Page 1
...JVB67 and JVB98 11 Dimensions and Clearances . .7, 8 Ductwork 8, 13, 15 Electrical and Gas Location . . . .8 Installation Possibilities 9 Installing the Downdraft Vent System 10-17 Optional Kits 17 Power Supply 12 Raise/Lower Switch 16 Venting Options 14
Troubleshooting Tips 18
Consumer Support
Consumer Support 20 Warranty 19
Owner's Manual & Installation Instructions
JVB37 JVB67 JVB94...
Use and Care Manual - Page 2
...hood ON when cooking at high settings. I Ducted fans must be locked, securely fasten a prominent warning device, such as those published by the manufacturer. TO REDUCE THE RISK OF A RANGE... oils slowly on accidentally. PLEASE NOTE: The downdraft vent system you do not damage electrical wiring and ... USING. Before servicing or cleaning unit, switch power off at service panel and lock ...
Use and Care Manual - Page 3
... is specifically recommended in this guide. B.
Do not attempt to repair or replace any part of the downdraft system unless it is small and contained in the area where it
system in the Install the Downdraft
blower motor or air vent mechanism. Reverse the steps in order to exhaust hazardous or explosive materials and...
Use and Care Manual - Page 4
... lowered.
NOTE: There is lowered. On some models, the Raise/Lower switch is being raised.
Raise/Lower Switch (30″ models only)
Turn the downdraft blower ON by again pressing the raise/lower switch at each end of the vent. Remote Raise/Lower Switch (36″ models only)
The 36″ models have a remote raise/lower...
Use and Care Manual - Page 5
... grasping them and pulling straight up.
Always wipe the surface in a water-bath canner, a gentle but steady boil must be cleaned at frying temperatures before replacing. The downdraft may also be maintained continuously for the required time. Canning
When canning foods in the direction of the grain.
Care and cleaning of the...
Use and Care Manual - Page 6
...Switch cover plate (1)
Attachment bracket (1)
6 This appliance must be properly grounded.
• Proper installation is not covered under the Warranty. TOOLS YOU WILL NEED
Flat-blade screwdriver
Carpenter square
REMOVE PACKAGING
Open the carton and remove parts package. Installation Instructions
Downdraft Vent...pad when changing or adjusting vent direction. PARTS INCLUDED
Stabilizing ...
Use and Care Manual - Page 7
B Ducted fans must be vented to determine requirements.
• A countertop with a raised lip or rolled front edge ...in accordance with a flat surface area of
fire, use only metal ductwork.
The vent and cooktop combined depth requires an extra deep flat countertop surface.
WARNING - IMPORTANT: These vents are limited due to back. (NOTE: JGP932S, JP350SC, JP930SC and JP938SC require...
Use and Care Manual - Page 8
... to Duct Fittings chart to use 31⁄4″ x 10″ ductwork.
REMOTE SWITCH
(for various duct configurations.
• The downdraft blower system is designed to calculate equivalent length for 36″ models only)
The downdraft vent has a separate raise/lower switch.
Clearance between cooktop and protected cabinetry must not be placed on appropriate placement...
Use and Care Manual - Page 10
... JP939
Overall Width 30-1/4″
29-3/4″
Cooktop Surface Surface Depth Overall Depth with Downdraft Vents
1
2
3
4
Model No. Installation Instructions
INSTALLING THE DOWNDRAFT VENT SYSTEM
30″ COOKTOP/DOWNDRAFT UNITS JVB37 AND JVB94
NOTE: Before you are installing with this downdraft vent system.
• Draw lines on the countertop to follow as a cutting guide.
• Make...
Use and Care Manual - Page 11
... JVB67 AND JVB98
NOTE: Before you are installing with this downdraft vent system.
• Draw lines on the countertop to follow as a cutting guide.
• Make sure sides of the opening are parallel and rear...
34″
22-1/8″
11 JP626
JP960 JP961 JP968 JP969
Overall Width 35-1/2″
36″
Cooktop Surface Surface Depth Overall Depth with Downdraft Vents
1
2
3
4
Model No.
Use and Care Manual - Page 12
Installation Instructions
INSTALLING THE DOWNDRAFT VENT SYSTEM
POWER SUPPLY
This downdraft vent must operate from the same duplex outlet.
See illustration.
Follow National electrical codes or prevailing local codes and ordinances.
12
The receptacle cannot be placed on the back of the vents' 2 foot power cord.
• Locate the receptacle inside the cabinet on the right...
Use and Care Manual - Page 13
... requirements for all equivalent feet values in the table should be doubled. Add equivalent lengths for good venting performance.
Duct Pieces
Equivalent Length*
31⁄4″ x 10″ 45° Elbow
5 ...12 ft.
21 ft.
27 ft.
6″ Round Roof Cap
20 ft.
6″ Round Roof Vent
24 ft.
See chart for CFM Duct Length.
13
Duct Pieces
31⁄4″ x 10″ ...
Use and Care Manual - Page 14
... and motor below the floor.
Discharge Direction The blower assembly may be removed and turned 90° for a left or right side discharge. • The downdraft vent is shipped with original screws. Order JXRB67 for installation of the opening .
• Flatten the shipping box to use as supplied)
• A left
Discharge right...
Use and Care Manual - Page 15
... calculate your installation. C Install 2 brackets on the side of case and attach to back of cabinet
Secure the lower brackets to blower housing
Place the downdraft vent into the countertop cutout, against the back side.
Laundry type wall caps should never be used if installing under a poured concrete slab. B Fasten 2 brackets to...
Use and Care Manual - Page 16
.... Control box
A Drill a 3/8″ hole into the hole. Connect Wire Lead to type of countertop. Installation Instructions INSTALLING THE DOWNDRAFT VENT SYSTEM
3 INSTALL THE RAISE/LOWER SWITCH
NOTE: Step 3 is for the Raise/Lower switch. WARNING - Disconnect electrical
power from the top of box
2 Pin connector
Strain relief
E Remove protective film from the unit...
Use and Care Manual - Page 17
... blower and motor assembly will be flush mounted when using this downdraft vent.
NOTES: • Accurate alignment of cooktop and
downdraft is necessary to move rearward when aligning the cooktop. Mounting brackets
JXBC67 optional outdoor cover accessory for indoor remote location of the downdraft cover.
• Using a dime as a thickness gauge, align the cooktop...
Use and Care Manual - Page 19
... trips to your home to your receipt here.
Some states do not allow the exclusion or limitation of the replaceable filters. Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support
GE Downdraft System Warranty.
I Improper installation, delivery or maintenance. This warranty is needed to one -year warranty, GE will also provide...
Quick Specs - Page 1
.... GE Profile™ 30" Telescopic Downdraft System
Overall Dimensions (in inches)
30
Venting Options (in most applications.
Approved for reference only. Against the wall installations are for use with a flat surface area of the countertop must be ordered for installation of motor and blower assembly in an indoor remote location.
JVB37HBB/CC/WW -
Quick Specs - Page 2
... GE Answer Center® service, 800.626.2000.
GE Profile™ 30" Telescopic Downdraft System
Venting Duct Information
DUCTWORK LENGTH AND DUCT FITTINGS
NOTE: Do not exceed 150 foot maximum permissible ...; 4″ x 10″ 90°Elbow
14 ft. The flexible metal duct should be doubled. JVB37HBB/CC/WW - DO NOT use with 3-1/4" x 10" ductwork (can be straight and smooth and extended ...
Quick Specs - Page 3
... vapors out of the kitchen • Removable grease filter - GE Profile™ 30" Telescopic Downdraft System
OFF RIGHT LO
1
3 2
OFF LEFT LO
1
3 2
JVB37HWW/CC/BB
4 4
Features and Benefits
• Telescopic downdraft hood - JVB37HBB/CC/WW - Black on white • Model JVB37HBB - Powerful 500-CFM performance removes smoke and vapors from the cooking area • Variable...
Similar Questions
Downdraft Stuck In Up Position
Downdraft vent stuck in up position. When down will rise, but will not return down. Removed switch t...
Downdraft vent stuck in up position. When down will rise, but will not return down. Removed switch t...
(Posted by hibbardhubbard 5 years ago)
Remove And Change Light Bulb On Ge Jvw5301 Range Hood
Page 9 says use a flathead screwdriver to remove ring but does not tell you how to do this. Push, pu...
Page 9 says use a flathead screwdriver to remove ring but does not tell you how to do this. Push, pu...
(Posted by ltindle 6 years ago)
Ge Jvx3300 Range Hood. How Do I Remove The Light Bulb Cover?
There's a little picture showing that you should use a screw driver, but nothing beyond that. I'm af...
There's a little picture showing that you should use a screw driver, but nothing beyond that. I'm af...
(Posted by Dontcallmehowie 7 years ago)
