Frigidaire GLEQ2152ES Support Question
Frigidaire GLEQ2152ES Support Question
Find answers below for this question about Frigidaire GLEQ2152ES - Electric Dryer.Need a Frigidaire GLEQ2152ES manual? We have 4 online manuals for this item!
Question posted by kathyromain on June 13th, 2011
How Do You Installl Heating Element?
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by OnlineOutreachSpecialist on June 16th, 2011 9:16 AM
OnlineOutreachSpecialist
Member since:
March 30th, 2011 Points: 2,848,320
Member since:
March 30th, 2011 Points: 2,848,320
This is not a typical do it yourself job. The heater assembly/element is behind the drum. You have to take apart the back of the unit, or go through the front and take apart the drum assembly.
We suggest a technician installing and testing the unit for your safety and liability.
Chris Polk
Online Outreach Representative
Electrolux Major Appliances, North America
[email protected]
Online Outreach Specialist
Related Frigidaire GLEQ2152ES Manual Pages
Use and Care Manual - Page 2
... model and serial numbers of your household waste disposal service or the shop where you to light any appliance. • Do not touch any electrical switch; Your dryer may be caused by inappropriate waste handling of this product. Important Safety Instructions
Your safety and the safety of others . This symbol alerts you...
Use and Care Manual - Page 3
... when using the drying rack. • - Some rubber materials, when heated, can occur. The interior of fire, electrical shock, or injury to a chemical reaction that could result in this warning can become airtight chambers. • Keep laundry products out of children's reach. The dryer must be cleaned approximately every 18 months by spontaneous combustion...
Use and Care Manual - Page 4
... add a dryer fabric softener sheet. 4. Dryer heat may not have it checked and reinstalled by a qualified service person. • To prevent personal injury or damage to 1/2 full. The dryer
will be ...
To reduce the risk of fire, electrical shock, or injury to persons, read and follow fabric care labels and laundry product labels. Close the dryer door and select the cycle, temperature...
Use and Care Manual - Page 5
... If the dryer drum becomes stained from using the drying rack. 4. Weight should clean the dryer cabinet interior and exhaust duct. Use only the Air Fluff/No Heat option for ... the dryer interior, unplug the electrical power cord to an exhaust outdoors.
Open the dryer door and remove the lint screen. 2. Insert drying rack into the dryer drum. Hazardous fumes or electrical shock...
Use and Care Manual - Page 6
... is clean and in washer or dryer to
electricity.
• Or, add a fabric softener sheet and
reduce static electricity.
• Lint screen not clean
tumble without heat.
• Remove items when they...not overload dryer. • Remove items as soon as cycle ends.
6 Care and Cleaning con't
Do not store or place laundry products on top of load
before starting the dryer. SOLUTIONS
...
Use and Care Manual - Page 7
... authorized service person for procedure.
Gas supply valve is not securely plugged in or plug may turn but won't heat. See INSTALLATION INSTRUCTIONS. Dryer should heat when utility service is not covered by the warranty.
7 Electric dryer is connected to make sure supply valve is blown, the drum may be at least 4 inches in INSTALLATION...
Technical Data Sheet - Page 1
...resistance of thermistor. Clear code, exit mode and start dryer. CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING Please Return This Sheet to the next code, press the OPTIONS... electronic control. Remove wires from control thermistor. Heater Fault (no heat, restricted vent, blower fan blade broken or loose, dryer installed in closet with communications or memory did not check, one...
Technical Data Sheet - Page 2
...numbers decrease.
After entering the test mode, the program knob can now be ON. heat source is off . heat source is on the both moisture sense bars at the same time will rapidly flash... on . heat source is off . heat source is off . When the DRYNESS key is off . Control thermistor reading is lit. heat source is pressed, all the Option LED's should light. Dryer will toggle ...
Installation Instructions - Page 2
... or straight blade screwdriver. 5. Rigid or flexible metal 4 inch (10.2 cm) duct. 7. Plastic knife. ELECTRICAL REQUIREMENTS
ELECTRIC Dryer
CIRCUIT - NEMA 10-30R
NEMA 14-30R
GAS Dryer
CIRCUIT - Do not store or use with clothes dryers. Follow the gas supplier's instructions. · If you cannot reach your gas supplier from plug. Phillips head screwdriver. 2. Duct...
Installation Instructions - Page 3
...hazard. The system back pressure MUST NOT be exhausted to assemble the exhaust system.
The dryer exhaust system MUST be higher than 0.75 inches of any screws or rivets to the...out damper(s) that open when the dryer is acceptable: 1. Do not install the dryer where gasoline or other obstruction. Restricted air flow will be exhausted into the laundry area. Exceeding the length of ...
Installation Instructions - Page 4
...accessible for rear exhausting.
A louvered door with the kit. However, on electric dryers, exhausting can be accomplished by installing Exhaust Kit, P/N 131456800, available through your dryer to the dryer.
6. Follow the instructions supplied with equivalent air openings for proper operation. A dryer installed in vent restriction. Installation MUST conform with local codes, or in...
Installation Instructions - Page 5
... for sides, rear, and top.
inches (387.1 sq. cm)
CLOSET DOOR
0" (0 cm)
15" (38.1 cm)
1" (2.54 cm) 0" (0 cm)
5
inches (387.1 sq. cm)
60 sq. This dryer MUST be exhausted outdoors.
5. MINIMUM INSTALLATION CLEARANCES -
Installation Instructions - Page 6
... (70.49cm) 28.5 to clear door handle (72.39cm)
2.375" (6.03cm)
(34.29cm) 13.5" To rear & base exhausts
27.0"
(68.58cm)
Stacked Dryer Installation Dimensions
(68.58cm) 27.0"
Electrical supply on rear of unit
28.25" to front of cabinet(71.76cm)
28.75" to clear knobs (73.03cm) 29.5" to clear...
Installation Instructions - Page 7
...of the cabinet.
NOTE: Remove one screw from each side), carefully lay the dryer on each of the dryer exhaust outlet.
4. This provision is not applicable, with no obstructions. Mobile ...the door swing may need a plastic knife to the floor. PACKING
REVERSING DOOR SWING
Your dryer is enclosed, the exhaust system MUST terminate outside the enclosure with the four screws.
4....
Installation Instructions - Page 8
...6. NOTE:
You may need a plastic knife to help remove the plugs. Be careful to the dryer front panel. Apply moderate downward pressure on the left by removing the door in Step 2. 4. Remove...the holes left side of the door and use later. Window Door Reversal Instructions
1. Open the dryer door. Remove the four hinge hole plugs from each hinge first. Support the door assembly firmly...
Installation Instructions - Page 9
... wiring and receptacle is properly grounded. In the event of a
malfunction or breakdown, grounding will have longer drying times than operating on the appliance. ELECTRICAL INSTALLATION
ELECTRIC Dryer
The following are specific requirements for the length power cord to be purchased, allowing some slack in the cord.
approved strain relief must be plugged...
Installation Instructions - Page 10
... relief mounting bracket to the silver-colored center terminal on the back of the dryer upper corner.
2. GREEN GROUND SCREW
NEUTRAL GROUND WIRE
SILVER TERMINAL
GREEN GROUND SCREW... MOUNTING B R A C K E T POWER CORD
POWER CORD
ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM
ELECTRIC Dryer
ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM
ELECTRIC Dryer
1. approved 30 amp power cord, NEMA 14-30 type ST or...
Operating Instructions - Page 1
...and protect fabrics.When the load has reached the selected dryness level, it tumbles through heated air.
Delicate Select this Auto Dry cycle for knits and delicate items.
Quick Select...Auto Dry cycles take the guesswork out of ventillation system, electrical voltage or gas pressure can also affect drying time.
See the "Dryer Settings Chart" for each cycle. When the cycle ends...
Operating Instructions - Page 2
..., follow the fabric care label instructions on items to freshen clothing, pillows or blankets;
Low heat is selected. to be heard periodically.
For loads requiring less drying time, select Less Dry....most cotton fabrics. When the Cycle Signal is lighted.
Dryer Features
Control To avoid having someone accidentally start or stop the dryer, press OPTIONS and SELECT at the same time until...
Operating Instructions - Page 3
...Dryer overloaded. Push button held too long or wedged in the Owner's Guide for assistance.
These temperatures, dryness levels and options are available with the following cycles:
Estimated drying time *** Temperatures
High Medium-High
Medium Low
No Heat... or the "Avoid Service Checklist" in the control panel. If the dryer stops, the status lights flash again, the beeping continues and the code...
Similar Questions
How To Replace Heating Element In Dryer Model Aeq7000eg0
(Posted by 19mcbriv 9 years ago)
Heating Element For Gleq2152es0 Frigidaire Dryer How To Repair
(Posted by rajibKimb 10 years ago)
How To Change A Heating Element Frigidaire Gleq2152es1 Dryer
(Posted by Pvbcece2 10 years ago)
Dryer Heating Element
Dryer heating element gets to hot and stays on even when the dryer is shut off.Gets hot enough that ...
Dryer heating element gets to hot and stays on even when the dryer is shut off.Gets hot enough that ...
(Posted by slong1022 10 years ago)
How To Change Heating Element On Frigidaire Dryer Model Gleq2152es
(Posted by oblonMara 10 years ago)