Epson TM-L90 Support Question
Epson TM-L90 Support Question
Find answers below for this question about Epson TM-L90.Need a Epson TM-L90 manual? We have 2 online manuals for this item!
Question posted by billygoatcoffee on December 11th, 2022
Backfeeding Linerless Labels
MY EPson tml90 is backfeeding the labels in and then getting rolled up and jammed. It will print a couple fine, then suck back the label and roll onto itself.
Current Answers
Answer #1: Posted by knaramadil on December 13th, 2022 1:47 AM
knaramadil
Member since:
December 9th, 2022 Points: 38,290
Member since:
December 9th, 2022 Points: 38,290
It sounds like your Epson TM-L90 label printer is experiencing a feeding issue, where the labels are being pulled back into the printer and rolled up. This can be caused by a variety of factors, such as a problem with the label roll, the print head, or the feeding mechanism.
To troubleshoot this issue, I would recommend trying the following steps:
- Make sure that the label roll is installed correctly and is not damaged or misaligned.
- Clean the print head and the feeding mechanism with a soft, dry cloth to remove any debris or buildup that may be causing the labels to stick or be pulled back into the printer.
- Adjust the label position and tension settings on the printer to ensure that the labels are being fed through properly and are not sticking to the print head or other parts of the printer.
- Check the printer settings to make sure that the correct label size and type are selected, and that the printer is set to the correct mode for printing labels.
- If the issue persists, try resetting the printer or performing a power cycle by unplugging the printer and then plugging it back in.
If you are unable to resolve the issue using these steps, it may be necessary to contact Epson support or take the printer to a repair shop for further assistance.
Answer #2: Posted by SonuKumar on December 11th, 2022 9:57 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,615,400
Member since:
May 9th, 2021 Points: 16,615,400
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Epson TM-L90 Manual Pages
User Manual - Page 2
... parties for errors or omissions. All rights reserved. No patent liability is a registered trademark of this product, or (excluding the U.S.) failure to change without the ... form or by Seiko Epson Corporation
2 TM-L90 User's Manual Depending on the area, the interface cable may be included with respect to this book, Seiko Epson Corporation assumes no responsibility ...
User Manual - Page 3
... line to fall into this section carefully and store it produces smoke, a strange odor, or unusual noise. TM-L90 User's Manual 3 CAUTION: Cautions must be damaged. Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for the drawer connector cable. Never disassemble or modify this manual are identified by foreign...
User Manual - Page 4
..., main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care, etc., please make your fingers on this product.
disaster prevention devices; Never stand or lean on the product indicate the following precautions. Caution Labels
The caution labels on this product's suitability after a full evaluation.
4 TM-L90 User's Manual various...
User Manual - Page 5
... panel label for horizontal installation* ❏ AC adapter* ❏ AC cable* * May not be downloaded from one of utilities and manuals can be included depending on the printer model. If any items are included. Downloading Utilities and Manuals
The latest versions of the following web site: http://download.epson-biz.com/?service=pos
TM-L90...
User Manual - Page 8
...the printer vertically (with the paper exit at least 3 or 4 times.
3.
Control panel label
2. Tighten the screw and make sure the lever moves smoothly.
8 TM-L90 User's Manual
Loosen the screw with a coin or similar tool and turn it at the ... the lever to the printer.
Installing the printer horizontally
1. Attach the control panel label. Lever Screw
Near-end sensor
Hole
4.
User Manual - Page 11
... also for the bundled label roll paper (or receipt paper). TM-L90 User's Manual 11 Open the roll paper cover. 2. See the TM-L90 Technical Reference Guide for screw
Notes on Changing the Paper Type
This printer is the only one to put the screw in.)
Hole for details. Go to http://www.epson.jp/dl-sd to...
Technical Reference - Page 3
... subject to change without notice.
ESC/POS is any liability assumed for damages resulting from the use of the information contained herein. ❏ Neither Seiko Epson Corporation nor its affiliates shall be reproduced, stored in a retrieval system, or transmitted in any form or by Seiko Epson Corporation. TM-L90/TM-L90 Peeler Model Technical Reference Guide Cautions...
Technical Reference - Page 5
Warnings
TM-L90/TM-L90 Peeler Model Technical Reference Guide
WARNING:
❏ Shut down your equipment immediately if it in.
• Be sure to push the...Handle the power cord with wet hands. Do not make modifications to fire or electric shock. Immediately unplug the equipment.
❏ Only disassemble this product or handle cables during a thunderstorm in order to avoid risk of the cord...
Technical Reference - Page 9
... Memory 106 Printer Status 106
Chapter 7 Handling
Maintenance 107 Cleaning the autocutter (TM-L90 only 107 Print Head Cleaning 109 Cleaning the peeler (TM-L90 Peeler Model only 110
Troubleshooting 111 Panel LED and Error Status 111 The autocutter is jammed or the roll paper cover will not open (TM-L90 only 118 When a paper jam occurs (TM-L90 Peeler Model 119
9
Technical Reference - Page 27
...)
Part names and the locations of paper. detector components 1.
detector holder Detector adjustment screw N.E. Open the roll paper cover. 2. Setup 27 TM-L90/TM-L90 Peeler Model Technical Reference Guide
2.3 Adjusting Roll Paper Near-End Detection Position 2.3.1 With TM-L90
Below are manufactured according to various specifications, making it impossible to suit the diameter of the...
Technical Reference - Page 60
...layout setting by the printer. The print area position influences the paper layout. Set the roll paper in paper feeding on printing. Note: The above automatic layout ...using the Memory Switch Setting Utility or ESC/POS command). Note: When using ESC/POS commands. Described below . ❏ TM-L90 setting procedure (Procedure for label paper, receipt paper, and receipt paper with ...
Technical Reference - Page 70
... onto the interface connector located on the connector panel. 2. The second TM printer can be connected using a USB cable.
*2 Epson does not supply the port driver or similar program necessary to the Host Computer and Options Connection procedure 1. For interface cables equipped with a ground line, attach the ground line to the screw hole...
Technical Reference - Page 72
... POS terminal or appropriate equipment other than the printer. Therefore, when using 1 printer with several PCs, it is necessary to take into the ferrite core.
3.2.4 With the Ethernet Interface (TM-L90 only)
TM printer...network with the Ethernet cable via a Hub.
10BASE-T/100BASE-TX
Note: The Ethernet interface TM printer does not accept a customer display (DM-D). If you reverse the order, the ...
Technical Reference - Page 75
Connecting to output the signal for each driver. For detailed information about ESC/POS commands, see the ESC/POS Command Reference. For details on page 85. TM-L90/TM-L90 Peeler Model Technical Reference Guide
CAUTION:
Since the buzzer drive signal and the cash drawer drive signal are common in the printer, do not use the same connector...
Technical Reference - Page 85
.../ and follow the on the driver and interface used to get the printer status using this printer and the information useful for development of applications using programming languages such as paper cutting and drawer opening. ❏ Can print the printer resident font by Epson.
TM-L90/TM-L90 Peeler Model Technical Reference Guide
Chapter 5
Application Development Information...
Technical Reference - Page 87
...the TrueType font will decrease printing speed due to the PDF User's Manual of available equipment.)
• Epson receipt printer • Epson customer display • Epson cash drawer
Note: The USB...
In that realizes ease of installation to get a log for debugging, and silent installation that case, use the printer resident font. When the TM-L90 is connected via a serial interface, it...
Technical Reference - Page 90
... on the ESC/POS commands, see "Introduction of Control Methods" on page 85. ❏ Utilities packed with various drivers • SetUpPOS Utility Equipment and connection ports can be selected, and various settings can be made. (Paper size, print waiting time setting, etc.) • TM Flash logo utility A bitmap file can be registered to the printer...
Technical Reference - Page 91
...-TX Ethernet interface for TM printer, and its detailed manual for adjustment. Get the utilities from the following URL. The normal printing task will be performed even in the near -end sensor is to detect the condition when the remaining amount of the roll paper by detecting the roll paper diameter. TM-L90/TM-L90 Peeler Model Technical Reference...
Technical Reference - Page 109
7.1.2 Print Head Cleaning
TM-L90/TM-L90 Peeler Model Technical Reference Guide
CAUTION:
The print head is very hot right after printing) before cleaning the print head. Be sure to allow the print head to "Paper Loading Method" on the roll paper used, paper dust may lower the print quality. Turn off the printer power before cleaning it . 4.
Note: Depending on page...
Technical Reference - Page 141
... (TM-L90)
The TM-L90 printing position and cutter positions are shown in the following figure.
29 14
Printing Position in Relation to feed paper
backward after an autocut.
•Back feed maximum amount
Receipt (without black mark):
Approximately 11.5 mm (back feed amount is fixed)
Receipt (with black mark):
Approximately 10.5 mm
Die cut label (without...
Similar Questions
How Can I Pair Epson Tm-t20ii Through Bluetooth?
I have a problem pairing with Bluetooth and what I do I can't get it to work please help.
I have a problem pairing with Bluetooth and what I do I can't get it to work please help.
(Posted by ondrejsirik 1 year ago)
I Have A K5 Printer On My Pos Equipment. Will The U220 Use The Same Cable?
Is the pin out on the rg45 connectors the same as k5?
Is the pin out on the rg45 connectors the same as k5?
(Posted by Raymondhayward3 10 years ago)
My Epson Tm-t88ii Partial Cut Is Getting Paused Every Now And Then... Solution?
my EPSON TM-T88II Partial cut is getting paused every now and then... i have changed the driver also...
my EPSON TM-T88II Partial cut is getting paused every now and then... i have changed the driver also...
(Posted by sameerkhan0088 11 years ago)
Driver Epson Tm-u590p For Mac Os X
HOW INSTALL POS PRINTER TM-U590P FOR MAC OS X
HOW INSTALL POS PRINTER TM-U590P FOR MAC OS X
(Posted by r1o2d3 12 years ago)