Dell PowerEdge 2950 Support Question
Dell PowerEdge 2950 Support Question
Find answers below for this question about Dell PowerEdge 2950.Need a Dell PowerEdge 2950 manual? We have 8 online manuals for this item!
Question posted by dozier1216 on October 16th, 2012
Romb Battery
Where is the ROMB battery located in the system?
Current Answers
Answer #1: Posted by GeoffatDell on October 16th, 2012 12:23 PM
GeoffatDell
Member since:
June 25th, 2012 Points: 24,740
Member since:
June 25th, 2012 Points: 24,740
From this download link, select the hardware manual pdf: http://support.dell.com/support/edocs/systems/pe2950/en/index.htm
On pge 75, figure 3-17, you will see the location of the ROMB battery; its located near the front of the server on top of the hard drive bay.
Removing a RAID Battery
1
Disconnect the cable between the RAID battery and the SAS RAID controller daughter card. See
Figure 3-17.
2
Press down and to the left on the battery carrier to disengage the carrier from the chassis battery carrier
slots.
3
Gently pulling back the two guides holding the RAID battery into the battery carrier, draw out the
RAID battery from the battery carrier.
Related Dell PowerEdge 2950 Manual Pages
Installing a SATA Optical Drive - Page 4
... board connected to the old drive.
1 Pull outward on the interposer board release tab at the back of the drive.
4
Installing a SATA Optical Drive Replacing a PowerEdge 2950 or 2970 Optical Drive
NOTE: If you are replacing an existing IDE optical drive, you are replacing an existing optical drive, do not require optical...
Installing a SATA Optical Drive - Page 5
... the back end of the drive. Installing a SATA Optical Drive
5 Replacing the Optical Drive in a PowerEdge 2950 or 2970 System
2 1
3
4
5
6
7
1 optical drive 3 interposer 5 SATA power cable 7 optical drive carrier
2 interposer release latch 4 SATA cable 6 carrier latch
Replacing a PowerEdge 1950 Optical Drive
NOTE: The replacement drive tray provided in the installation kit must be...
Installing a SATA Optical Drive - Page 7
Installing the SATA Optical Drive -
SATA Cable Routing in the PowerEdge 1950 2
1
3
4
6
5
1 SATA data cable 3 chipset shroud 5 SATA power cable
2 SATA_A... supply connector.
See "SAS Controller Daughter Card" in your Hardware Owner's Manual.
6 Close the system. PowerEdge 2970 or 2950
1 Insert the optical drive tray into the system until it is fully inserted and locked into position.
2...
Installing a SATA Optical Drive - Page 8
... bracket toward the front of the system until the bracket detaches from the chassis slots.
6 Route the SATA cable in the cable channel in the PowerEdge 2950 and 2970
1
2
3 4 5
1 SATA_B connector on the system board. See Figure 1-4.
7 Route the SATA cable along the top of the chassis and replace the cable retention...
Information Update - Page 1
Dell™ PowerEdge™ 2950 Systems
Information Update
Information Update - Page 3
Contents
Non-Optimal Memory Configurations 5 PowerEdge 2950 III - New System Features 5
New Performance Features 5 New High-Efficiency Power Supply and Power ... - Safeguarding Encrypted Data 9 System Message Update 10 LCD Status Messages Update 15
Contents
3 PowerEdge 2950 III Systems 9 Processor Upgrades - Power 2950 II and PowerEdge 2950 III Systems 9 System Board Replacement -
Information Update - Page 5
PowerEdge 2950 III -
Information Update
5
New System Features
New Performance Features
• Two dual-core or quad-core Intel® Xeon® 5400 Series and 5300 Series ...
Information Update - Page 9
...for your system, verify that was shipped with a "III", your system. Power 2950 II and PowerEdge 2950 III Systems
• If the front of your system chassis is labeled with ... PowerEdge 2950 III Systems
PowerEdge 2950 III systems have added support for 8-GB Memory Modules - For more than 4 GB of the hard drive.
Safeguarding Encrypted Data
On PowerEdge 2950 III systems using Windows Server&#...
Information Update - Page 10
... of a possible problem with the system.
Check
(for example, a failed
other system messages
DIMM) so that node
for additional information
interleaving cannot be
for the PowerEdge 2950 III system and the probable cause and corrective action when the message appears.
Be sure to create a recovery key during system setup. If you replace...
Information Update - Page 15
... Status Messages
Code N/A
E1000 E1118
Text SYSTEM NAME
FAILSAFE, Call Support CPU Temp Interface
Causes
Corrective Actions
A 62-character string that can occur on the PowerEdge 2950 III system and the probable cause for critical failure events. You can be defined by the user in the System Setup program. LCD Status Messages...
Information Update - Page 21
... network. When set to Enabled, I /OAT)
Engine
option. Changes take effect after the system reboots.
System Interrupts This field controls the interrupt assignment for the PowerEdge 2950 III system.
Information Update - Page 24
...by the PowerEdge 2950 and 2950 II systems, but not by the PowerEdge 2950 III ...system. You cannot save the file to specify the diskette drive or USB memory key where the test log file is saved.
System Support for Microsoft Windows 2000
If you to a hard drive.
24
Information Update System Diagnostics Update
In the Customize window of operating systems on the Server...
Information Update - Page 27
目录
29
PowerEdge 2950 III 29 29 29 全新 I/O 30 30
内部 USB 30 USB 30
支持 8 GB PowerEdge 2950 III 32
PowerEdge 2950 II 和 PowerEdge 2950 III 32
32
33
LCD 37
40 Memory 40 CPU Information （CPU 42 Integrated Devices 42 System Security 44 Serial Communication 45
目录
27
Information Update - Page 29
POST Non-Optimal Memory Configuration Press F1 to continue or F2 for Setup （按 F1 F2
DIMM DIMM
PowerEdge 2950 III
全新性能
Intel® Xeon® 5400 系列和 5300 8 GB
BMC
信息更新
29
Information Update - Page 33
... not be available... PCIe
PCIe
SAS
No boot device available
USB CD
USB
程序"。
信息更新
33
表 1-1 列出了 PowerEdge 2950 III
表 1-1
信息
原因
纠正措施
Alert!
Information Update - Page 44
System Security
表 1-7 PowerEdge 2950 III TPM。
TPM Security（TPM TPM。
表 1-7. New System Security
选项
说明
TPM Security
TPM
（TPM Off [
关
]）
...
Information Update - Page 46
Microsoft Windows 2000
System Build and Update Utility Microsoft® Windows® 2000 将位于 Server OS Install PowerEdge 2950 和 2950 II PowerEdge 2950 III
Customize Log output file pathname USB
46
信息更新
Information Update - Page 132
...; cat/sys/devices/system/cpu/cpuxx/cpufreq/scaling_ cur_freq
• RHEL 3 9 Intel Xeon 54xx proc/cpuinfo
RHEL 4
Microsoft Windows 2000
System Build and Update Utility Server OS Install OS OS Microsoft® Windows® 2000 PowerEdge 2950/2950 II OS PowerEdge 2950 III
Customize Log output file pathname USB
132
Information Update - Page 157
Microsoft Windows 2000
Microsoft® Windows® 2000 이 Server OS Install(서버 OS PowerEdge 2950 III 대신 PowerEdge 2950 및 2950 II
Customize Log output file pathname USB
157
Hardware Owner's Manual (PDF) - Page 118
...may lose its system configuration information. This situation is lit. See "System Battery" on page 131. 2 Locate the faulty power supply. If the problem is turned off the system ...2 Turn off for the time kept in the System Setup program, replace the battery.
See "Using Server Administrator Diagnostics" on page 96. Troubleshooting Power Supplies
Problem • System-status indicators...
Similar Questions
Dell Server Poweredge R710 Error Message Error 1
hi Good Day,we are having issue with our dell R710 with error message error 1 but we look up in OMSA...
hi Good Day,we are having issue with our dell R710 with error message error 1 but we look up in OMSA...
(Posted by jillustrisimo32 4 years ago)
How To Configure Raid In Dell Server Poweredge 710
(Posted by brandaniep 10 years ago)
How To Replace Romb Battery In Dell Poweredge 2950
(Posted by scLero 10 years ago)