Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by mrsis on August 24th, 2013
How To Do A Factory Reset On Dell Powerconnect 6248
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 6248 Manual Pages
User's Guide - Page 5
... XFP Module Port LEDs 65 10/100/1000 Base-T Port LEDs 65 System LEDs 67 Stacking LEDs 68
5 Configuring Dell PowerConnect
Overview 71 Starting the CLI 72 General Configuration Information 74
Terminal Connection Configuration 74 Baud Rate 74 Other Configuration Requirements 74 Booting the Switch 75 Configuration Overview 81 Easy Setup Wizard 81
5
User's Guide - Page 19
... • Multicast Features • Additional Documentation
Introduction
19 The Dell PowerConnect 6248 supports 48 1000Base-T copper ports and 4 "combo" ports for PoE capability. Release notes are standalone Layer 2 and 3 switches that extend the Dell PowerConnect LAN switching product range. The Dell™ PowerConnect™ 6200 series are provided with hot swappable stack members...
User's Guide - Page 52
Bay 1 and Bay 2 Interfaces
The Dell™ PowerConnect™ 6200series switches support dual 10 Gb slot interfaces.
Bay 1 and Bay 2 PowerConnect 6200 Series 10 Gb Slots
Serial Cable Connection
You can use a computer running terminal emulation software). The switch's serial cable is a female to the terminal (console) ASCII DTE RS-232. 2. Connect the serial cable to...
User's Guide - Page 71
... you will not be able to monitor the boot process and other functions is powered up for this section. Configuring Dell PowerConnect
71
You can download the release notes from the Dell Support website at support.dell.com/manuals. This switch lights the Master Switch LED. Performing other procedures.
For the initial configuration, perform the standard...
User's Guide - Page 72
... line only.
1. You can be defined. NOTE: If you 're directly connected to the switch before using CLI commands.
72
Configuring Dell PowerConnect When finished, exit the session with the quit or exit command. However, to access the switch through Telnet, at least one user account must be managed over a direct connection to the...
User's Guide - Page 73
...)
Reboot
No
Loading program from flash to RAM
Yes Enter Wizard
No
Initial Configuration: IP Address, Subnetmask, Users Basic Security configuration
Wizard Configuration Process
Standard Switch Installation
Advanced Configuration: IP Address from DHCP, IP Address from bootp, Security management
Advanced Switch Installation
Configuring Dell PowerConnect
73
User's Guide - Page 74
... delivered with Telnet, SSH, and so forth
74
Configuring Dell PowerConnect
The configuration process consists of the switch to its unique network topology.
Other Configuration Requirements The following is required for downloading embedded software and configuring the switch: • ASCII terminal (or emulation) connected to match the speed of the unit • Assigned IP...
User's Guide - Page 75
... of simultaneously open files: 22
Configuring Dell PowerConnect
75 To enter the Boot menu, press 2 within the first ten seconds after the following steps:
1. Start Boot Menu. The following text is loaded into RAM. Turn on the terminal and indicate test success or failure. As the switch boots, the boot test first counts...
User's Guide - Page 77
Delete backup image 9 - Activate Backup Image 12 - To return to factory defaults (delete config files) 11 - Retrieve event log using XMODEM 5 - Update boot code 8 - The following output displays an example configuration. Operational Code Date: Tue May 26 14:12:20 2009
Configuring Dell PowerConnect
77 Restore configuration to operational code from the [Boot Menu...
User's Guide - Page 80
... RamCP: as rawFs, device = 0x20001 Formatting...OK.
(Unit 1 - Applying Interface configuration, please wait ...
console> After the switch boots successfully, a prompt appears and you can use the local terminal to select management unit)>
Applying Global configuration, please wait ... See "Software Download and Reboot."
80
Configuring Dell PowerConnect Waiting to begin configuring the...
User's Guide - Page 81
... factory configuration. The initial account is not necessary (skip the procedures in the basic initial configuration of the switch ...is given the highest privilege level (level 15).
• Enables CLI login and HTTP/HTTPS access to set up the following information from the network administrator:
• Is the network setup for the autoconfig feature? Configuring Dell PowerConnect...
User's Guide - Page 82
... set-up the default gateway IP address.
If there is only presented again if you reset the switch to configure security access for SNMPv3 (for example, engine ID, view, etc.). The next... Setup Wizard.
82
Configuring Dell PowerConnect You may include spaces. • Sets up the SNMP community string to be powered on in the field without a serial connection, the switch waits 60 seconds for you...
User's Guide - Page 84
...60 seconds)? [Y/N] y
Step 1:
84
Configuring Dell PowerConnect Would you like to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you can access the
...is configured for the general flow.
Help text is accepted. Waiting to manually configure the switch. NOTE: In the example below, the possible user options are examples only. Also, where...
User's Guide - Page 85
... "community string" or password that the particular management system uses to access the switch.
You may setup other management interfaces to change privilege levels later. For more...
Step 3:
Configuring Dell PowerConnect
85 Would you like to the CLI and Web interface. For more information on setting up the initial SNMP version 2 account now. To manage the switch using SNMP (required...
User's Guide - Page 97
...Dell PowerConnect
97 The version number shows during the boot process, press 2 within ten seconds after the first part of the POST is extracted from the next-active image and programmed to reboot the switch... command:
console#update bootcode
Update bootcode and reset (Y/N)? 2. Start operational code.
2 -
Start Boot Menu. For each switch, the bootcode is completed. Enter y to...
User's Guide - Page 98
...Code Date: Tue Apr 29 10:15:36 2008
Uncompressing.....
50%
100%
98
Configuring Dell PowerConnect Display operational code vital product data 6 - Abort boot code update 7 - To relaunch... from the Boot menu, select 1 on the Boot menu and press . Delete backup image 9 - Reset the system 10 - The Boot menu displays and contains the following configuration functions: 1 - Load new ...
User's Guide - Page 103
...Factory Defaults Use option 10 to load using the system default configuration and to its default setting.
The active image becomes the backup when this option is confirmed with a Y/N question before executing the command. image2 activated.
2. The boot process resumes. Reset... and deletes the configuration files. Configuring Dell PowerConnect
103 The boot process starts over.
Activate...
Release Notes - Page 3
... 6224/6224F/6224P/6248/6248P Release Notes
Introduction
This document provides specific information for the Dell PowerConnect 6200 Series switches, firmware version 3.2.0.6. Global Support
For information regarding the latest available firmware, release note revisions, or additional assistance, please visit the
Support Web Site http://support.dell.com/. NOTE: The PC6200 switches when stacked...
Release Notes - Page 4
...Supported
PowerConnect 6224 PowerConnect 6248 PowerConnect 6224F PowerConnect 6224P PowerConnect 6248P
2
System Firmware Version 3.2.0.6
NOTE: OMNM 4.1 will not discover the switches running...to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide and the Dell™ PowerConnect™ 6200 Series Configuration Guide. Users should upgrade to a PowerConnect 62xx device...
Release Notes - Page 25
...the factory the...required to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide for 90 seconds.
If "n" is typed, the session is executed. Default: The switch remains in modules...Default: Disabled by default.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
RADIUS Accounting Servers
Title radius-server host acct
Description The switches do not support creating ...
Similar Questions
