Brother International DreamMaker„ XE Innov-is VE2200 Support Question
Brother International DreamMaker„ XE Innov-is VE2200 Support Question
Find answers below for this question about Brother International DreamMaker„ XE Innov-is VE2200.Need a Brother International DreamMaker„ XE Innov-is VE2200 manual? We have 2 online manuals for this item!
Question posted by thousandjan on April 23rd, 2015
Automatic Needle Threader Needs Adjusting. Missing Eye To Thread Through
broke a needle and now my threader is out of line. I had repaired once but could I adjust this myself without the expense of a repair service.
Current Answers
Related Brother International DreamMaker„ XE Innov-is VE2200 Manual Pages
Users Manual - English - Page 10
... cap to raise and lower the needle. B-8
c Presser foot lever
Raise and lower the presser foot lever to raise and lower the presser foot. (page B-42)
d Air vent
The air vent allows the air surrounding the motor to thread the machine and wind the bobbin. Before using the machine, carefully read these descriptions to...
Users Manual - English - Page 12
...B-10 Press this button to automatically thread the needle. CAUTION
• Do not press the thread cutter button after embroidering to automatically trim the excess thread. e "Automatic Threading" button
Use this button again to the fabric. The button changes color according to raise or lower the needle. Red:
The machine cannot embroider.
b "Needle Position" button
Press this button...
Users Manual - English - Page 24
... turned on (see page E-26)
CAUTION
• If "Upper and Bobbin Thread Sensor" is set to "OFF", remove the upper thread.
LCD SCREEN
Using the Machine Setting Mode Key
Press
to change the default machine settings (needle stop position (the needle position when the machine is not operating) to be up or down position when using the...
Users Manual - English - Page 31
... these movies for
in the movies.
better understanding of the screen. Press a key to open the machine help screen. Five categories are displayed at the top of the functions. displays troubleshooting
displays information about
threading the machine, changing embroidery attaching the embroidery unit, changing
feet, etc. displays information about
displays information about...
Users Manual - English - Page 32
of the screen will change.
LCD SCREEN
Example: Displaying information about upper threading
a Press
. c Press
(upper threading).
→ The screen shows instructions for threading the machine. Press
to the
beginning.
Press
to view the previous page. Press movie.
to close out the
* Press to view the next page.
* Press to pause. b ...
Users Manual - English - Page 39
... left corner of the bobbin case. a Tab * Be sure to the right. Be sure to cut it is not inserted correctly, reinstall the thread.
B
1
Then, pull the thread toward you to thread the machine as shown, guide the thread
through the slit (a and b).
* At this time, check that the bobbin easily rotates counterclockwise.
Otherwise, the...
Users Manual - English - Page 40
...that the upper threading is equipped with the automatic threading function. a Upper thread shutter
Memo
• This machine is performed correctly. c
Press the "Needle the needle.
Note
• If you to thread the needle automatically without raising the needle, the thread may not thread correctly.
Memo • The automatic threading function can cause the thread to tangle and...
Users Manual - English - Page 43
... with the needle threader.
Then, pass the thread through the eye of the needle after passing the thread through the needle bar thread guide (marked "6"), manually pass the thread
1
through the eye of the needle. n
Carefully pull the end of the thread that 5 cm - 6 cm (approx. 2 inches - 2-1/2 inches) of thread are pulled out.
• It may be necessary to adjust the thread tension...
Users Manual - English - Page 85
... how to sew your
embroidery project without enough thread in the frame (see page E-31). Memo • If you will need to rewind the bobbin in the middle of bobbin case types below . Included bobbin case varies depending on this case can adjust thread tension with different weights of bobbin threads and a variety of machine. The screw...
Users Manual - English - Page 86
Sewing Embroidery Patterns
Example:
b
a
a Groove b Projection c Notch To remove the embroidery needle plate cover, place your left hand.
If the embroidery needle plate cover is being used, there may cause the needle to the needle plate.
a
Thread the machine with thread for any applications other than embroidery. E-22 In this case, attach the included embroidery needle ...
Users Manual - English - Page 87
... embroidering the pattern, making it may show
,
, or
. Press
, and the display
will automatically trim the threads and stop the machine.
button
to
start embroidering. e
Remove the thread for an appliqué inside the pattern. Thread the machine with an appliqué, the color sewing order display shows "APPLIQUE MATERIAL", "APPLIQUE POSITION", "APPLIQUE", and then the...
Users Manual - English - Page 152
...6
CREATING BOBBIN WORK 8
Selecting the Pattern 8 Start Embroidering 10
ADJUSTING THE THREAD TENSION 12
■ Adjusting the upper thread tension 12 ■ Adjusting the tension of the bobbin thread 12
TROUBLESHOOTING 13
■ The thread was accidentally cut automatically and the bobbin thread is caught inside the machine 13
■ Correcting bobbin work tension 13 ■ The bobbin...
Users Manual - English - Page 154
...the embroidery unit.
PREPARING FOR BOBBIN WORK
■ Upper thread
Embroidery thread (polyester thread) or monofilament (transparent nylon) thread. Before creating bobbin work . Upper Threading
a Needle plate cover
d Remove the bobbin case. c Thread the machine with LED pointer "W+"
* Included accessories vary depending on threading the machine, refer to be replaced with the one for the...
Users Manual - English - Page 156
... the machine.
• Do not guide the bobbin thread through the groove in the trial pattern is too tight and adjusting the bobbin case tension does not help, do not pass the thread through the tension spring as shown below.
■ When tension is not applied to the bobbin thread
If the bobbin thread in the needle...
Users Manual - English - Page 157
...
not allow it to Create Bobbin Work
→ A loop of
the machine.
m
Gently pull the upper thread to repeat the procedure from a, otherwise the lower threading will not be sure to bring the bobbin thread up through bobbin thread loop and pull bobbin thread above the needle
plate.
Appendix A-7 q Install the embroidery unit. PREPARING FOR BOBBIN WORK...
Users Manual - English - Page 160
...needle may result in "reverse" of normal
embroidering.
a Upper thread b Bobbin thread
Memo
• If the bobbin thread cannot be pulled up through the
to surface. j
While holding the upper
thread...thread above fabric, rotate the handwheel
the
counterclockwise while holding both the upper thread and the bobbin thread, sew... to help pull bobbin thread to
fabric.
CREATING BOBBIN...
Users Manual - English - Page 161
... thread. Use a ribbon embroidering needle to hand sew stitches to
secure the threads. When cutting the threads, be sure to "100 spm". Memo
• If there is set to leave an adequate length of thread so they can be achieved, adjust the tension of fabric
p
If the desired results could not be properly secured.
k
Stop the machine, and thread...
Users Manual - English - Page 162
... cause damage to check the results.
■ Adjusting the upper thread tension
We recommend a setting between 6 and 8 for bobbin work . After adjusting the tensions, be achieved after adjusting the upper thread tension, adjust the tension of the bobbin case (gray), and then insert the bobbin case into the machine. Turning the screw too much or providing force...
Users Manual - English - Page 169
... following possible problems before requesting service.
wrong spool cap, spool cap is loose, the thread did not catch the needle bar threader, etc.)
Needle is turned, bent or the point is twisted. Adjust the thread tension. Reinstall the needle correctly. Thread is dull.
use a bobbin designed specifically for this
machine. B-36
Maintenance and Troubleshooting
A
2
Appendix...
Users Manual - English - Page 170
... the bobbin case, or consult your authorized dealer.
Adjust the thread tension setting. Needle is a mistake in the race.
Stabilizer is incorrect. Thread tension is set incorrectly.
while sewing
Upper threading is not attached to fabric being embroidered.
use a bobbin designed specifically for this
machine.
bobbin. The thread that was pulled out was not wound Wind the...
Similar Questions
A Spool Of Thread Has Wound Itself Around The Hand Wheel?
The motor began to labour & I stopped the machine immediately. I removed as much of the thread a...
The motor began to labour & I stopped the machine immediately. I removed as much of the thread a...
(Posted by ronmcwhae 7 years ago)
Why Won't My Needle Thread..machine Is Only 1 Month Old.
(Posted by cyndibrown01 9 years ago)
What Size Of Needle Do I Need To Use In Brother Sewing Machine Vx 1120
(Posted by amjackpage 10 years ago)
How To Replace Automatic Needle Threader
My present is broken, need to replace
My present is broken, need to replace
(Posted by rolltide28879 10 years ago)