Audiovox APS996A Support Question
Audiovox APS996A Support Question
Find answers below for this question about Audiovox APS996A - Prestige Remote Security System.Need a Audiovox APS996A manual? We have 1 online manual for this item!
Question posted by cuharlee on December 30th, 2020
I Changed Battery. Now Truck Wont Start
The person who posted this question about this Audiovox product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Audiovox APS996A Manual Pages
Instruction Manual - Page 3
... In The Engine Compartment, as the module or wiring may be terminated. Secure the siren mounting bracket using #8 self taping screws or by first using the...to change Press transmitter lock button to change
or Press and release the valet switch Press transmitter Lock button to change Press transmitter Lock button to change
or ...Remote Start/Alarm System is not accessible from below the vehicle.
Instruction Manual - Page 4
... provided with this will not penetrate any existing factory wiring or fluid lines. After securing the antenna with double stick tape provided. This will serve as some newer vehicles ...location and pass the connector end of the ignition switch to facilitate this hood switch prevents the remote start activation even if the RF command to a fixed support. Carefully drill a 1/4" hole in...
Instruction Manual - Page 5
...! RED Wire: + 12 Volts Battery 2 Source Connect this combination Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be secured to an existing wiring harness as ...blower motor, and accessories exceed 24 Amps continuous, we recommend that two fuses be used for the start solenoid wire. Whichever mounting method is not available then secure the relay's ...
Instruction Manual - Page 6
...that the vehicle cannot start (crank) position only. SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. VIOLET Wire: Accessory Output Connect this wire to the "OFF" and "ACCESSORY" positions. This wire... to the ignition switch side of the of this wire must be made to test the remote start unit and ensure that powers the glow plugs if the vehicle requires glow plug pre-heating...
Instruction Manual - Page 8
...the zone clears, the siren will be connected to be shunted when remote starting the vehicle and will remain shunted all the while there is ground ...lighting see programming under command of the remote start. Positive Door Switch Wiring Detail
Dark Green Wire: (-) Instant Trigger Input This is armed, the siren will be connected to confirm full arming. Secure the Black wire of 28 NOTE:...
Instruction Manual - Page 9
... #30 and the other side of the relay to a fused + 12 volt battery source. B. Ignition 3 Output: Some newer vehicles use a third ignition wire which is not shunted during the Remote Start activation period, then vibration from the
ignition switch to start and keep the vehicle's engine running from the running plus an additional 4 seconds...
Instruction Manual - Page 10
...Input Plus Trigger When Armed The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module whenever it is grounded also trigger for relay wiring details. This wire may result in... Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to do so may also be used if the vehicle...
Instruction Manual - Page 11
...wire to control the starter inhibit relay. This will have 0 volts in turn cause the remote start solenoid wire found at the vehicles ignition switch harness. The brake input will have + ... Plus Trigger When Armed The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module whenever it gets + 12 volts also triggers the alarm when armed.
Connect terminal...
Instruction Manual - Page 12
... while running under command of the chassis.
Be certain to remove any paint or grease and secure this wire to more than one multi coil pack regardless of the number of cylinders. See multi.... Negative Door Switch Wiring Detail
11
128-6773 12 of the Remote Start module. This wire will emit three chirps.
This Remote Start unit learns the tach rate of the vehicle and in most cases...
Instruction Manual - Page 13
...300 mA Horn Output The black w/ white trace wire is provided to a fused + 12 VDC battery source. Connect relay terminal 87 to the vehicle's horn switch output, and connect relay terminal 30 ... equivalent. Dark Blue/Black Trace Wire: External Trigger Input The Dark Blue/Black trace wire allows the remote start the vehicle. Connect Terminals #85 and # 30 to a fused + 12 Volts source with a current...
Instruction Manual - Page 14
... Green/Yellow Wire: DIESEL WAIT TO START INPUT The green/yellow wire, when connected to ground via an independent RF channel from the security system, the starter disable feature will remain...channel 5. If this wire will provide a 1 second 300ma pulsed ground output after the remote start unit. WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current...
Instruction Manual - Page 15
.... NOTE: The outputs above are the ground supply and program/ valet/override input of the Remote Start unit. This will be used for continuous read transponder circuits. NOTE: If using the TWO WAY...& Grey twin lead wires loaded in the two pin red connector enable the operation of the Remote Start unit. Route the twin lead Black and Grey wires from the antenna receiver assemble into the...
Instruction Manual - Page 18
ALARM SELECTABLE FEATURES NOTE: The Alarm Selectable Features and Remote Start Selectable Features programming steps following are based on your particular vehicle for channel 2. RF Programmable Features:
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
Default
1st DoorL/...
Instruction Manual - Page 19
... to start diesel, it is to keep the battery charged
and fluids warm. If your vehicle is a instant start at timed intervals. To Program The Remote Start Selectable...Off, On (4 times) to the ignition circuits. TEMPERATURE START:
When Temperature Start, feature #11 is to select a
4 hour timed start interval. To
change selectable feature 3, press and release channel 1 button on then...
Instruction Manual - Page 20
...Coil Pack Adaptor: (Optional)
The multi coil pack adaptor is designed for the last remote start shutdown. Turn the ignition key to pass between steps, or the programming mode will ... four coil systems, connect to change the selection of the circles. 2. The Remote Start Unit will begin to the (Green) or (Orange/Green) tach input of the Audiovox remote start button on as follows:
1 ...
Instruction Manual - Page 21
... manner may result in the on the control module. Failure to prevent the Remote Start unit from starting while the gear selector is to test the unit in the following procedure must...of this test, recheck your enable switch connection to prevent operation of the Remote Start Unit regardless of the remote start switch is firmly seated in the mating connector on (Closed To Ground)...
Instruction Manual - Page 22
... GM Park/Neutral ECM input circuit. Shown is the preferred method of safety when installing a remote start position or be connected to the drive position. Locate the Orange / Black reference wire in the...enable switch to accommodate this reference wire. 3. When you are installing the Audiovox Remote Start Unit in sensor. Keeping the brake pedal depressed, activate the RF transmitter in ...
Instruction Manual - Page 23
...battery.
NOTE: When completing an installation using either alternative. Method 1 will be reconfigured to allow a margin of a vehicle utilizing an electrical neutral start switch and is inconsistent with a Mechanical Neutral Start Switch from starting...will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear other than ...
Instruction Manual - Page 24
... Connect terminal 86 of the Remote Start Unit. The anode (Non Striped) side must be connected to the Gray/Black wire of the relay to a fused +12 volt constant battery source. If the hood pin... second 4002 series diode may be certain to use the dual diode assembly packaged with the Audiovox Remote Start Unit as shown in the diagram above. B. If this same wire, and connect the (non...
Instruction Manual - Page 25
... may come in contact with this type of interior light, we suggest you have confirmed the operation of the Audiovox Remote Start unit and tested all wiring up and behind the dash securing it in the engine compartment. The unit will begin flashing the Armed indication indicating the unit has exited the learn...
Similar Questions
Where I Can My Remote Alarm
(Posted by anpcrony 1 year ago)
How To Determine Model Prestige Alarm
(Posted by mjsinryan78 10 years ago)
Prestige Remote Start Aps997 Car Wont Start With Key
(Posted by kiuvn 10 years ago)
Prestige Platinum Aps997n How To Start Without Remote
(Posted by joir 10 years ago)
Problem With Prestige 996c Alarm System
My alarm is chriping and windows have rolled up on there own because I got a window module on it. Do...
My alarm is chriping and windows have rolled up on there own because I got a window module on it. Do...
(Posted by Jttt29 13 years ago)