Get support for Audiovox APS996A - Prestige Remote Security System

Audiovox APS996A Support Question

Audiovox APS996A Support Question

Find answers below for this question about Audiovox APS996A - Prestige Remote Security System.
Need a Audiovox APS996A manual? We have 1 online manual for this item!
Question posted by mjsinryan78 on March 13th, 2014

How To Determine Model Prestige Alarm

The person who posted this question about this Audiovox product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Audiovox APS996A Manual Pages

Instruction Manual - Page 1

... Valet 11th Two Step Unlock On Off Off 12th Chirp Delete From Tx On Off Off To program these selectable features; lock, dbl 1 sec. RY Model APS 996a Installation Manual SELECTABLE FEATURES Note : The method of manual override can either be selected to change or Press and release the valet switch...
Instruction Manual - Page 3

...Automatic Transmission- Avoid mounting the module to allow more than 15 seconds to the input wire activating the alarm. Secure the module in your chosen location to a "Wait To Start Input" either of which may wrap around... connection of the 6 pin main wiring harness. The APS-996 Remote Start/Alarm System is activated, (hood/trunk open), it is not accessible from below the vehicle.
Instruction Manual - Page 4

... for the body of the switch, and also that will serve as a visual indicator of the alarm's status and provide a visual deterrent to the operator of the switch, and also that is easily... with tape, we advise also securing a section of the vehicle for best reception. Inspect behind the chosen location to do so may be mounted to the operator of the remote start is issued. hood switch is...
Instruction Manual - Page 5

... Connect this wire to a + 12 VDC constant source found later in this combination Alarm/Remote Start unit is used by the battery 1 source. Secure the relay to allow routing and connecting of the ignition switch's low current start relay and the accessory relay. If the vehicle, running , and to the sensitivity adjustment potentiometer for...
Instruction Manual - Page 6

... wire will show + 12 volts when the ignition key is turned to the "OFF" and "ACCESSORY" positions. Understanding the difference between the starter inhibit relay, ( when used ). This wire will show...the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions, and will show 0 volts when the key is turned to test the remote start unit and ensure that powers the glow...
Instruction Manual - Page 8

...: (+) Siren Output This is removed. In most door lighting circuits are wired in the firewall to first disarm the alarm system. Secure the Black wire of the Siren to the Red wire of the remote start. Note for 5 seconds after the ground is the positive siren feed wire. This wire will be shunted...
Instruction Manual - Page 9

...below, a relay will be used with the alarm system and it is not shunted during the Remote Start activation period, then vibration from the Remote Start Unit to accommodate the following diagram is ...situations: A. For GM PASS LOCK System you will need to the third ignition wire in later model Cadillacs, they are run through an orange sleeve, and are typically White w/ Black trace and Violet...
Instruction Manual - Page 10

... ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is a safety wire and must be connected ...Input Plus Trigger When Armed The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module whenever it is grounded also trigger for relay wiring details. If the pin ...
Instruction Manual - Page 11

...brake switch. Orange Wire: Ground When Armed Output This wire provides a 300 mA ground output when the alarm circuit is off. See detail in the vehicle that is +12 volts when the ignition switch is turned ... The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module whenever it gets + 12 volts also triggers the alarm when armed. Connect one side of 28
Instruction Manual - Page 12

... This wire will remain shunted, if active, while running under title "Completing The Installation". This Remote Start unit learns the tach rate of the vehicle and in most cases will operate properly from one... source or to a solid clean metal part of the remote start. Be certain to remove any paint or grease and secure this manual for wiring detail. This wire will emit three chirps.
Instruction Manual - Page 13

...of 28 Dark Blue/Black Trace Wire: External Trigger Input The Dark Blue/Black trace wire allows the remote start the vehicle. This is a low current (300mA) output and must be connected to a relay ... relay to supply power to the device you wish to the low current ground output from the alarm should only be connected ). Connect relay terminal 87 to the vehicle's horn switch output, and ...
Instruction Manual - Page 14

...opened starter cut arrangement, and when power is removed from the security system, the starter disable feature will remain operational, and the ...to off. 13 128-6773 14 of the factory alarm when the remote start sees the green/yellow with glow plug preheat...DIESEL WAIT TO START INPUT The green/yellow wire, when connected to determine if they occur will provide a 1 second 300 mA pulsed ground ...
Instruction Manual - Page 15

...Output: (Yellow Connector) This output is intended to allow the unit to be used to the remote start is operable. Route the twin lead Black & Black w/ White Trace wires from the control ...output when the unlock button of 28 When the Grey wire is started . Refer to the remote programming, feature programming and function programming shown later in a two step circuit. The Red w/Black...
Instruction Manual - Page 18

... 128-6773 18 of additional components which may include relays, fixed resistors, or for channel 2. ALARM SELECTABLE FEATURES NOTE: The Alarm Selectable Features and Remote Start Selectable Features programming steps following are based on your particular vehicle for alarm selectable features. Refer to pages 1 and 2 for properly connecting to these types of circuits. U/L 1 Sec...
Instruction Manual - Page 19

... operation, (Feature Nine), over gasoline, the only change , the above sequence will chirp 2X or 4X dependant upon 2 or 4 hour interval setting. START PROGRAM: The Remote Start unit has the ability to start the vehicle automatically at 4 hour intervals. The lights will flash and the siren will power up 10, 15...
Instruction Manual - Page 20

...are not sure what the setting for any of times indicating the reason for the last remote start trigger wire reactivated. 6 Flashes High tach signal (RPM) 7 Flashes Tach signal has... or Negative inhibit wire activation 4 Flashes Control switch moved to start the vehicle via the remote start position and have accessed the diagnostic mode, the unit will not flash. For vehicles utilizing...
Instruction Manual - Page 21

...is to allow the vehicle operator to the off . To test the integrity of the Audiovox Remote Start Unit. If the unit fails this test, recheck your pin switch connection to complete ... the control of the RF transmitter operation. Move the switch to prevent operation of the Remote Start Unit regardless of the remote start unit. 4. If you have a plug in personal injury, property damage, or...
Instruction Manual - Page 22

...5. Repeat the above test this test, recheck your Yellow Wire's connection. To connect the Audiovox remote start unit to the drive position. Keeping the brake pedal depressed, activate the RF transmitter in the...shown below shows a typical GM B Body ECM reference wire and how it will help you to determine if the vehicle you feel the engine pull, do not offer the same level of the Neutral...
Instruction Manual - Page 24

... above . Cut this is also used for an alarm trigger input, be certain to use the dual diode assembly packaged with the Audiovox Remote Start Unit as shown in this installation guide. (...of the previously cut in step D. The cathode (Striped) side must be connected to the Remote Start Negative Safety Shut down circuit. Cut this wire and connect the ignition cylinder side to ...
Instruction Manual - Page 25

...during installation, and retest the system. 7. Replace all activated features and safety systems associated with Remote Start Unit installed to initiate the dome delay. The unit will begin flashing the Armed indication...learn the dome light delay time, up and behind the dash securing it in place with cable ties or screws. Securely harness and tie all wiring up and away from the program...

Similar Questions

Ask a New Question
Use the box below to post a new question about this Audiovox product .
Points & Prizes
  • You can earn points for nearly everything you do on HelpOwl.com
  • You can trade in those points for gift cards at leading retailers such as Amazon.com and Walmart
  • It's that simple!
See How it Works
Create a Free Account

Audiovox Manuals

Find free Audiovox APS996A - Prestige Remote Security System manuals and user guides available at ManualOwl.com. Try out our unique manual viewer allowing you to interact with manuals from directly within your browser!

Audiovox Reviews

View thousands of Audiovox user reviews and customer ratings available at ReviewOwl.com.

Contact Information

Complete Audiovox customer service contact information including steps to reach representatives, hours of operation, customer support links and more from ContactHelp.com.

Scoreboard Ratings

See detailed Audiovox customer service rankings, employee comments and much more from our sister site.

Audiovox Recalls

Find comprehensive Audiovox recall information updated hourly on RecallOwl.com.