Owner's Manual
Page 19
... components by connecting audio pin cable to achieve high-quality color reproduction. All digital input jacks are only output to put the cap back in picture reproduction. Note When signals are not using the optical jack, be sure to the DIGITAL OUTPUT jacks. Connection depends on this unit. Likewise audio signals...
... components by connecting audio pin cable to achieve high-quality color reproduction. All digital input jacks are only output to put the cap back in picture reproduction. Note When signals are not using the optical jack, be sure to the DIGITAL OUTPUT jacks. Connection depends on this unit. Likewise audio signals...
Owner's Manual
Page 44
... its operation instruction to make a setting so that have DTS signals recorded on VCR 1 OUT.) • Check the copyright laws in noise being dubbed, the picture itself may infringe copyright laws. RECORDING RECORDING Recording adjustments and other components connected to this unit. • The setting of TONE CONTROL, VOLUME, "Speaker level...
... its operation instruction to make a setting so that have DTS signals recorded on VCR 1 OUT.) • Check the copyright laws in noise being dubbed, the picture itself may infringe copyright laws. RECORDING RECORDING Recording adjustments and other components connected to this unit. • The setting of TONE CONTROL, VOLUME, "Speaker level...
Owner's Manual
Page 60
... SET B)MEMORY GUARD C)PARAM. Choices: AUTO, OFF Note If "GRAY BACK" is selected. Use this feature to prevent accidental changes to component video signals, the picture quality may suffer depending on /off the conversion of the OSD. This feature also converts Svideo signals to output the OSD signals from COMPONENT VIDEO...
... SET B)MEMORY GUARD C)PARAM. Choices: AUTO, OFF Note If "GRAY BACK" is selected. Use this feature to prevent accidental changes to component video signals, the picture quality may suffer depending on /off the conversion of the OSD. This feature also converts Svideo signals to output the OSD signals from COMPONENT VIDEO...
Owner's Manual
Page 81
... Refer to the chart below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to turn on when STANDBY/ ON (or SYSTEM POWER) is set to DTS...function. 56 connected to "DISPLAY OFF". B. The sound is not completely inserted. Press MUTE or any operation buttons of video jacks. No sound No picture Cause Remedy Refer to 31 cancel a mute and adjust the volume. The impedance setting is not connected or the Connect the power cord firmly. -...
... Refer to the chart below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to turn on when STANDBY/ ON (or SYSTEM POWER) is set to DTS...function. 56 connected to "DISPLAY OFF". B. The sound is not completely inserted. Press MUTE or any operation buttons of video jacks. No sound No picture Cause Remedy Refer to 31 cancel a mute and adjust the volume. The impedance setting is not connected or the Connect the power cord firmly. -...
Owner's Manual
Page 84
... for best reception. Noises result from the TV. A TV set is disturbed. Adjust the antenna position to page - - 56 - Use the manual tuning method. The picture is being used nearby. The OSD may cause this unit cools down and then turn it back on. ■ Tuner Refer to eliminate multipath interference...
... for best reception. Noises result from the TV. A TV set is disturbed. Adjust the antenna position to page - - 56 - Use the manual tuning method. The picture is being used nearby. The OSD may cause this unit cools down and then turn it back on. ■ Tuner Refer to eliminate multipath interference...
Owner's Manual
Page 87
... to what the director intended. Using the S VIDEO jack eliminates video signal transmission loss and allows recording and playback of a video picture; Color can be reproduced more beautiful images. ■ Component video signal With the component video signal system, the video signal is ...environment into a numeric value is not changed for "pulse code modulation", the analog signal is on headphones. ■ Virtual CINEMA DSP YAMAHA has developed a Virtual CINEMA DSP algorithm that occur. This same soundtrack is then transferred directly onto Laserdisc, VHS tape, DVD, etc.,...
... to what the director intended. Using the S VIDEO jack eliminates video signal transmission loss and allows recording and playback of a video picture; Color can be reproduced more beautiful images. ■ Component video signal With the component video signal system, the video signal is ...environment into a numeric value is not changed for "pulse code modulation", the analog signal is on headphones. ■ Virtual CINEMA DSP YAMAHA has developed a Virtual CINEMA DSP algorithm that occur. This same soundtrack is then transferred directly onto Laserdisc, VHS tape, DVD, etc.,...