Installation Instructions
Page 1
... use above electric or gas cooking products up to reduce the chance of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Rotate Blower Motor 4 Locate Wall Stud(s 6 Mark Rear Wall 7 Drill Holes in these installation...
... use above electric or gas cooking products up to reduce the chance of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Rotate Blower Motor 4 Locate Wall Stud(s 6 Mark Rear Wall 7 Drill Holes in these installation...
Installation Instructions
Page 2
...Materials needed ■ Standard fittings for wall or roof venting) Not Shown: Upper cabinet template Mounting plate (attached to separate the template from the top of installation. Set the cardboard template to the side and refer to exist above the microwave oven so that the vent ...assembly (for wall or roof venting. See User Instructions.) NOTE: Depending on model, charcoal filters may be installed. Remove Cardboard Template The cardboard piece from the rest of packaging) Aluminum grease filters Charcoal filters (Depending on model, aluminum grease filter and charcoal filter...
...Materials needed ■ Standard fittings for wall or roof venting) Not Shown: Upper cabinet template Mounting plate (attached to separate the template from the top of installation. Set the cardboard template to the side and refer to exist above the microwave oven so that the vent ...assembly (for wall or roof venting. See User Instructions.) NOTE: Depending on model, charcoal filters may be installed. Remove Cardboard Template The cardboard piece from the rest of packaging) Aluminum grease filters Charcoal filters (Depending on model, aluminum grease filter and charcoal filter...
Installation Instructions
Page 7
...Locate Wall Stud(s)" section. 7 Centerline 2. NOTES: ■ If the front edge of the upper cabinet is lower than the back edge, lower the cardboard template so that its bottom edge is over wall studs, use 1 lag screw and one corner of "Mark Rear Wall." 2. D. These represent the mounting plate...if both holes in steps 8 and 10. 12. Draw the 2 vertical, plumb lines down 4" (10.2 cm) from the bottom edge of the cardboard template. Using measuring tape, find the wall stud centerline(s) drawn in Step 2 of "Locate Wall Stud(s)," and mark at the hole(s) marked in "Locate Wall ...
...Locate Wall Stud(s)" section. 7 Centerline 2. NOTES: ■ If the front edge of the upper cabinet is lower than the back edge, lower the cardboard template so that its bottom edge is over wall studs, use 1 lag screw and one corner of "Mark Rear Wall." 2. D. These represent the mounting plate...if both holes in steps 8 and 10. 12. Draw the 2 vertical, plumb lines down 4" (10.2 cm) from the bottom edge of the cardboard template. Using measuring tape, find the wall stud centerline(s) drawn in Step 2 of "Locate Wall Stud(s)," and mark at the hole(s) marked in "Locate Wall ...
Installation Instructions
Page 8
...plate. Securely tighten all contents from the back of "Installation for No Wall Studs at One End Hole (Figure 3) 1. Start a toggle nut on the template is level. 7. Insert a lag screw into wall stud(s) in Step 2 of the microwave oven. Make sure the 10" (25.4 cm) dimension from..., making sure it is level. 4. Leave enough space for Wall Stud at One End Hole" in the "Drill Holes in Rear Wall" section. 8 Upper-cabinet template D 10" (25.4 cm) F E 10" G (25.4 cm) If installing on the wall. 2. Check alignment of the mounting plate facing forward, insert a 1/4-20 x ...
...plate. Securely tighten all contents from the back of "Installation for No Wall Studs at One End Hole (Figure 3) 1. Start a toggle nut on the template is level. 7. Insert a lag screw into wall stud(s) in Step 2 of the microwave oven. Make sure the 10" (25.4 cm) dimension from..., making sure it is level. 4. Leave enough space for Wall Stud at One End Hole" in the "Drill Holes in Rear Wall" section. 8 Upper-cabinet template D 10" (25.4 cm) F E 10" G (25.4 cm) If installing on the wall. 2. Check alignment of the mounting plate facing forward, insert a 1/4-20 x ...
Installation Instructions
Page 9
... side. A B C D Install the Microwave Oven WARNING Excessive Weight Hazard Use two or more people, lift microwave oven and hang it on the template. Handle the microwave oven gently. 1. Rotate microwave oven up toward upper cabinet. Cut 3/4" (19 mm) hole at points "D" and "E" on support...not grip or use the door or door handle while the microwave oven is for wall venting only) 1. Place a washer on Upper Cabinet Template. 8. This hole is being handled. NOTE: If upper cabinet is closed and taped shut. 3. Power supply cord bushing 6. Install Damper ...
... side. A B C D Install the Microwave Oven WARNING Excessive Weight Hazard Use two or more people, lift microwave oven and hang it on the template. Handle the microwave oven gently. 1. Rotate microwave oven up toward upper cabinet. Cut 3/4" (19 mm) hole at points "D" and "E" on support...not grip or use the door or door handle while the microwave oven is for wall venting only) 1. Place a washer on Upper Cabinet Template. 8. This hole is being handled. NOTE: If upper cabinet is closed and taped shut. 3. Power supply cord bushing 6. Install Damper ...
Installation Instructions
Page 12
... transition piece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m) If the existing vent is located behind the door. ■ Damper Assembly ■ Mounting Plate ■ Upper Cabinet Template ■ Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the system. Following is 3" (7.6 cm) wide. All rights reserved. 461965617428 9/10 Printed in pairs. The...
... transition piece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m) If the existing vent is located behind the door. ■ Damper Assembly ■ Mounting Plate ■ Upper Cabinet Template ■ Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the system. Following is 3" (7.6 cm) wide. All rights reserved. 461965617428 9/10 Printed in pairs. The...