Via NX 15000G - VIA EPIA Nano ITX Motherboard Support and Manuals
Get Help and Manuals for this VIA Technologies item
This item is in your list!
View All Support Options Below
Free Via NX 15000G manuals!
Problems with Via NX 15000G?
Ask a Question
Free Via NX 15000G manuals!
Problems with Via NX 15000G?
Ask a Question
Via NX 15000G Videos
Popular Via NX 15000G Manual Pages
User Manual - Page 6
TABLE OF CONTENTS
SPECIFICATIONS 1
MAINBOARD SPECIFICATIONS 2 MAINBOARD LAYOUT 4 BACK PANEL LAYOUT 4
INSTALLATION 5
CPU 6 CPU Fan and System Fan: CPU_FAN and SYS_FAN 6
MEMORY MODULE INSTALLATION 7 Memory Slot: DDR2_SODIMM 7 Available DDR2 SDRAM Configurations 7
CONNECTING THE POWER SUPPLY 8 Nano-ITX 12-Pin Power Connector 8
BACK PANEL PORTS 9 RJ45 LAN Port 9
CONNECTORS 10 IDE ...
User Manual - Page 10
...:mm:ss 50 PNP/PCI CONFIGURATIONS 51 PNP OS Installed 51 Reset Configuration Data 51 Resource Controlled By 52 PCI/VGA Palette Snoop 52 Assign IRQ For VGA/USB 52 Maximum ASPM supported 52 Maximum Payload Size 52 FREQUENCY / VOLTAGE CONTROL ... Time (Twr 55 RDSAIT mode 55 LOAD FAIL-SAFE DEFAULTS 56 LOAD OPTIMIZED DEFAULTS 57 SET SUPERVISOR / USER PASSWORD 58 SAVE & EXIT SETUP 60
vi
User Manual - Page 13
The mainboard enables the creation of an exciting new generation of a Mini-ITX mainboard. CHAPTER 1
Specifications
The ultra-compact and highly integrated VIA EPIA-NX Nano-ITX mainboard is the smallest form-factor available today. Through a high level of integration, the Nano-ITX measures at only 50% of the size of small, ergonomic, innovative and affordable embedded systems.
1
User Manual - Page 15
... connector to support 2nd LVDS panel (VT1636 add-on card required) • 1 x Audio connector: Line-out, Line-in, MIC-in, and S/PDIF out • 1 x TV out connector for Composite, S-Video, or Component (YPbPr) • 1 x Video pin connector for VGA output, CCIR656/601 video input and SMBUS • 2 x SATA connectors • 1 x Nano-ITX power...
User Manual - Page 18
... Signal
1
NC
2
+12V
3
GND
13
6 The processor requires a heatsink with fan for 1.5GHz SKU and a fanless heatsink for 1.2GHz SKU. Chapter 2
CPU
The VIA EPIA-NX Nano-ITX mainboard can support VIA C7 NanoBGA2 and VIA Eden NanoBGA2 processors. When connecting the wire to the connectors, always be aware that the red wire (positive wire) should...
User Manual - Page 19
... INSTALLATION
Installation
Memory Slot: DDR2_SODIMM
The VIA EPIA-NX Nano-ITX mainboard provides one SODIMM slot for available DDR2 SDRAM configurations on the mainboard.
Insert the SODIMM module at a 45 degree angle.
Push the SODIMM module back towards the board until the clips lock the module in place. Slot
Module Size
SODIMM
64MB, 128MB, 256MB, 512MB, 1GB
Maximum supported...
User Manual - Page 20
Then push down the plug firmly into the connector.
Nano-ITX 12-Pin Power Connector
To connect the power supply, make sure that all components are aligned. ... in the proper orientation and the pins are installed correctly to ensure that no damage will be caused. Chapter 2
CONNECTING THE POWER SUPPLY
The VIA EPIA-NX Nano-ITX mainboard supports a Nano-ITX power supply for the power system.
User Manual - Page 44
...-OS2, OS2]
Video BIOS Shadow
Enabled copies Video BIOS to repeat the signal from a depressed key.
Settings: [Enabled, Disabled]
32
Setting
Setup
System
Description
Password prompt appears only when end users try to run BIOS Setup Password prompt appears every time when the computer is required every time the System boots, or only when you are...
User Manual - Page 51
..., 1G]
AGP 2.0 Mode
This mainboard supports the AGP 4x interface. The aperture is backward compatible, leave the default 4x mode on. Settings: [4x, 2x, 1x]
39 AGP 4x is a portion of the PCI memory address range dedicated to the AGP without any translation.
AGP & P2P BRIDGE CONTROL
BIOS Setup
Phoenix - AGP 4x mode can...
User Manual - Page 63
... ** Maximum ASPM supported Maximum Payload Size
[No] [Disabled]
[Auto(ESCD)] Press Enter
[Disabled] [Enabled] [Enabled]
[L0s&L1] [4096]
Item Help
Menu Level
Select Yes if you are using a Plug and Play capable operating system. Setting
Enabled
Disabled
Description
Resets the ESCD (Extended System Configuration Data) after exiting BIOS Setup if a newly installed PCI card...
User Manual - Page 65
... MHz, 133 MHz, 166 MHz, 200MHz, 266MHz]
Auto Detect PCI Clk
Settings: [Disabled, Enabled]
Spread Spectrum
When the mainboard's clock generator pulses, the extreme values (spikes) of the pulses are reduced to flatter curves. FREQUENCY / VOLTAGE CONTROL
BIOS Setup
Phoenix - AwardBIOS CMOS Setup Utility Frequency / Voltage Control
DRAM Clock/Drive Control Auto Detect PCI...
User Manual - Page 66
...
DRAM Timing
The value in this field depends on the memory modules installed in your system.
Changing the value from the factory setting is not recommended unless you install new memory that has a different performance rating than the original modules. AwardBIOS CMOS Setup Utility PnP / PCI Configurations
DRAM Clock DRAM Timing x SDRAM CAS Latency...
User Manual - Page 77
The CD should then appear on the "Start" button and select "Run..." Then type: "D:\Setup.exe". Driver Installation
Running the Driver Utilities CD
To start using the CD, insert the CD into the CD-ROM or DVD-ROM drive. The driver utilities and software menu screen should run automatically, click on the screen. If the CD...
User Manual - Page 78
... 4
CD CONTENT
VIA 4in1 Drivers: Contains VIA ATAPI Vendor Support Driver (enables the performance enhancing bus mastering functions on ATA-capable Hard Disk Drives and ensures IDE device compatibility), AGP VxD Driver (provides service routines to your VGA driver and interface directly to hardware, providing fast graphical access), IRQ Routing Miniport Driver (sets the system's PCI IRQ routing...
Via NX 15000G Reviews
Do you have an experience with the Via NX 15000G that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Via yet.
Earn 750 points for your review!