URC MRF-250 Support and Manuals
Get Help and Manuals for this URC item
Popular URC MRF-250 Manual Pages
Owners Manual - Page 1
•
MRF-25 INSTALLATI
MANUAL
\\_
Multi-Room "No-Pointing" RF Control of Audio/Video Components HOME THEATERMASTEW
Entertainment Made Simple-
Owners Manual - Page 2
... form without prior notice. X Universal Remote Control°
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 MRF-250 Installation Manual © 2004 Universal Remote Control, Inc. Home Theater Master is a registered trademark of this manual is a trademark of their respective companies or organizations. No part of Universal Remote Control, Inc.
Owners Manual - Page 3
... Multiple Equipment Locations
II
Frequently Asked Questions
I2
Specifications
12 Introduction
Features and Benefits
2
Parts Guide
2
Front Panel
3
Mounting Plate
3
Power LED
3
Status LED
3
Front Blaster
3
Rear Panel
4
Flashers
4
Power Supply
4
Bottom Panel
4
Receiver ID#
4
A Standard MRF-250 System
5
Standard Installation - Step by Step
5
Front Blaster Overload...
Owners Manual - Page 4
... the same cabinet space as the MRF-250.
3. The MRF-250's built-in Front Blaster sends commands to components in to the MRF-250's rear flasher line outputs via their 10 foot cables. The MRF-250 converts your commands to the MRF-250 throughout your house (50-100' away, indoors or outdoors). The MX-3000 remote control sends radio waves in another...
Owners Manual - Page 5
... just as easily for wall mounting the MRF-250 4 - Parts Guide
The MRF-250 RF Base Station includes: I - 9V-300mA Power Supply 6 - Mounting Plate for them (thus allowing up to control out of the MX-3000 remote control from within and nearby your home and the amount of interference generated by installing an MRF-250 base station at any direction. Screws for...
Owners Manual - Page 6
... in the same cabinet space. MRF-250 Details
Red POWER LED lights when the MRF-250's power supply is plugged into place for mounting on the wall.
Page 3 Red STATUS LED lights when the MRF-250 receives an RF signal from the MX-3000.
The MRF-250's slots enable the Mounting Plate's matching guides to slide and "snap" into...
Owners Manual - Page 7
...-adhesive pads (in any direction to be repositioned). Included 9V power supply plugs into the MRF-250's power connector. Page 4 Six Rear Flasher Line Output Jacks connect flashers for control of A/V components out of sight of the MRF250's Front Blaster. I, I
MRF-250 BASE STATION
gen
Integrated Antenna swings in case a flasher has to optimize RF reception...
Owners Manual - Page 8
...remote controls to program, use the downloadable Programming Manual or the animated Tutorial. You do not need to utilize MX3000 Editor's Program Step 9 (RF Control), since the factory settings will control as possible. Important Note: Do NOT power up the MRF-250 at this point! Place the MRF-250 The MRF-250 should be
Page 5 A Standard MRF-250...an MRF-250 for standard system installations ...
Owners Manual - Page 9
... a jacket or pillow, test the control of the MRF-250 receiving antenna via it's pivoting ball ...MRF250's Front Blaster will need to operate.
The MRF-250 must move the MRF-250 to the rear wall or back of the component. This tells you must always be powered up to extend the range of the remote...cabinet walls and doors. Once you have problems with the enclosed screws, then the receiver...
Owners Manual - Page 10
... 2 - Page 7 Important Note: Always replace the self-adhesive tabs if you have more than six components you can purchase an additional MRF-250 (available as the first unit) then follow the steps on the following pages:
Disabling the Front Blaster -
Front Blaster Overload
A few models of components your MRF-250 can control to apply your Home Theater...
Owners Manual - Page 11
... must use Flashers instead. Create a Device for each of the identical devices to control identical components. Using either the IR Database or Learning, program one of the TVs...device for the rest of the identical components.
Controlling An Array of Identical TV's (or VCR's, Receivers, CD players etc.)
There are installing an MRF-250 to control the rest of TV's (leave the others ...
Owners Manual - Page 12
... Open the RF Setup Window The RF Setup window opens after selecting RF Control from the three options shown in the pull down list box . Tx*: None
T:3
The RF Setup window is NOT
...:. Step 3 - By looking at the column for Flashers, you can see that the factory default programming sets all of your work. Both options must be changed for EACH of the other identical device. Save your ...
Owners Manual - Page 13
...Page 10 Default Default iefaut Default Default Default
Dutpv. You may leave the other components of the Identical Devices
The RF Setup window enables you select TV I TV 4
Signal IFI & RF IR & RF IR & RF IR & RF IR... & FIF IR & RF
RF
IR & RF
- Adjust the Flashers For Each of the system set to IR & RF.
Next, Save your MX-3000.
Likewise for the first identical TV, by clicking on ...
Owners Manual - Page 14
...ID# for each LOCATION by Default receiver to install
multiple MRF-250's in :
Step I -
Reveal the Receiver settings Extend the RF Setup window by clicking on their
Name, then clicking
...MRF-250 assigned a unique Receiver ID#.
Cancel
Step 4 -
Each LOCATION should have
a unique ID#. Page 11 Open the RF Setup Window
The RF Setup window opens after selecting RF Control ...
Owners Manual - Page 15
...set...MRF-250? I have already installed in the system to connect to the selected TV also responds. Frequently Asked Questions
Can I use flasher/emitters that I have a row of identical TV's.
Specifications
MRF-250... Shack part # 274-327 to convert 3.5mm plug Flasher/Emitters to fit the MRF-250's flasher...can increase range by repositioning the MRF-250 and/or by reorienting the antenna...
URC MRF-250 Reviews
We have not received any reviews for URC yet.