TRENDnet TE100-S16plus Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TE100-S16plus manuals!
Problems with TRENDnet TE100-S16plus?
Ask a Question
Free TRENDnet TE100-S16plus manuals!
Problems with TRENDnet TE100-S16plus?
Ask a Question
Popular TRENDnet TE100-S16plus Manual Pages
Data Sheet - Page 1
... module bay for network backbone and multimedia applications. Supporting "Port Trunking" and Quality of Service (QoS), TRENDnet's TE100-S16plus is a high performance, autosensing 16-port NWay rack-mountable Fast Ethernet Switch. Cost Effectiveness: Provide 10/100Mbps of 8 trunk ports are available with port 8
Integrate address Look-Up Engine, supports up to 2Km away (in Networking
16...
Data Sheet - Page 2
TE100-S16plus
16-port 10/100Mbps NWay Switch (Rack Mount)
SPECIFICATIONS
Standards: • IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX/100Base-FX ...
TE100-SFXM: Multimode SC-Type Fiber Slide-in this document pertain to change at any time, without notice.
USA
Tel: 310-891-1100
R
Fax: 310-891-1111
TRENDnet
Web: www.TRENDNET.com
TRENDware, USA
Email: [email protected]
TRENDnet is...
Manual - Page 9
... 100Mbps, while maintaining the CSMA/CD Ethernet protocol. It is an extension of the 10Mbps Ethernet standard with all 10Mbps Ethernet environments, it provides a straightforward upgrade and takes advantage of the Switch and some background information about Ethernet/Fast Ethernet switching technology.
INTRODUCTION
This chapter describes the features of the existing...
Manual - Page 10
...be used to setup, and
2 The switch supports both traditional 10Mbps...problems of uplinking Fast Ethernet hubs beyond the limits of switching technology. LAN Switching technology is a marked improvement over the previous generation of network bridges, which is the development of Ethernet technology is also ideal for network transmission capacity. Routers have also been used to split parts...
Manual - Page 11
...-duplex mode), each port can connect to today's local area network congestion problems.
Features
This high performance Switch was designed for each port.
The Switch ...Switch, with its standard rack-mount size, is less expensive, easier to setup, and practically maintenance free, which make it an ideal solution to the Switch...support 200Mbps, the Switch can be upgraded to large workgroups.
Manual - Page 12
... for cascading two or more
Switches (same model).
4 Three QoS levels; Supports two trunking groups for any port. eliminates all error packets, runts, etc. ?? 16K active ...another switch or hub.
?? This allows auto-sensing of complete frame checking and error frame filtering, this scheme prevents error packages from transmitting among segments.
?? Other key features are as followed:
??...
Manual - Page 13
... This User's Guide If any item is found missing or damaged, please contact your local reseller for the acceptable operating temperature and humidity ranges.
?? Installation
The site where you install the Switch may greatly affect its contents. See Technical Specification for replacement. UNPACKING AND INSTALLATION
This chapter provides unpacking and setup information for ventilation...
Manual - Page 14
...reinstall the dusk cover when the slot is the same. Gently slide the module along the guides in the slot and firmly seat it in the module's package.
1. For information on a...2. When installing the Switch on a level surface, attach the rubber feet on the module slot. Note: 1. Install the Switch on a sturdy, level surface that can support its weight, or on rack installation, please ...
Manual - Page 18
... power connector
Trunk QoS
Module Slot
Qos setting DIP switch
Power switch
Module Slot:
For installing optional fiber module for 100BASE-FX connection. Port 8 and the Uplink port is really the same port, except that their pin-outs are different.
For detail information on how to setup QoS, please refer to the Trunking...
Manual - Page 19
... network. It remains off indicating no power. Note: the full-duplex LED lights green when the connected device supports full-duplex operation. 10M Link/ACT and 100M Link/ACT (10Mbps Link/Activity (amber) and 100Mbps Link/Activity... lights green when the respective port is connected to the installed fiber module. This indicator lights amber when the port is in fullduplex (FDX) mode.
Manual - Page 20
...traffic is heavy between the Switches. You can select to set the
dipswitches. 3. Please follow the instructions below for more ) Switches via one trunking group (...select the trunk ports and set the trunking dipswitches:
Note: You can only trunk same model Switches together. 1. Follow the table above to 800Mbps; Trunking setting
This Switch supports trunking function. or cascade...
Manual - Page 22
...). When data packets with QoS priority information pass through QoS supported device, these packets will be handled with three levels of priority settings.
Port based priority ensures transmission with precedence for user to set traffic prioritization according to network congestions. Without certain level of Service (QoS) is also provided for
20 Port-Based Priority...
Manual - Page 23
...The QoS DIP Switches 1~8 represent port number 3~6 and 11~14. When the DIP Switch is set for Port-Based QoS.
IP Header QoS:
The QoS DIP Switch 9 enables/disables IP header QoS... feature. VLAN Tag QoS:
21 Disable Enable
QoS
Note: Please power off the Switch before setting the QoS dipswitches. V LA N Ta g
IP Header Port 1 4
Port 1 3
Port 1 2
Port 11
Port ...
Manual - Page 24
... the LAN adapter is ok to the VLAN tagging priority information.
PC to Switch
A PC can be connected to Switch connection:
1. After the connection is set at "Enable", the Switch will show the status of the 16 ports (1x - 16x)
Note: Use CAT5 (or better) cable for 10Mbps connection.
2. If LED...
Manual - Page 27
Port S peed & Duplex Mode
After a connection is made between the Switch and another Ethernet device, the system uses auto-negotiation to determine the transmission mode for this twisted-pair connection: If the attached device does not support auto-negotiation or has auto-negotiation disabled, an auto-sensing process is initiated to select the speed and set the duplex mode to half-duplex.
25
TRENDnet TE100-S16plus Reviews
We have not received any reviews for TRENDnet yet.