TRENDnet TE100-S86FX Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TE100-S86FX manuals!
Problems with TRENDnet TE100-S86FX?
Ask a Question
Free TRENDnet TE100-S86FX manuals!
Problems with TRENDnet TE100-S86FX?
Ask a Question
Popular TRENDnet TE100-S86FX Manual Pages
Manual - Page 1
... about these topics, please refer to install and use the provided eightport Fast Ethernet Switch, which features that 10/100BASE-TX ports automatically sense the presence of 100Mbps or 10Mbps Ethernet networks. 100BASE-FX Multi-mode and Single-mode fiber ports are also available for this manual, you should have an understanding...
Manual - Page 2
... 4
Benefits of Switching 4 Eight Ports Ethernet Switch 5 Product Features 7 Packing List 7 Front Panel 8
Ports 8 LEDs 10
Installation 14
Selecting a Site for the Switch 14 Connecting to Power 15 Connecting to LAN & Ethernet
Technologies 19
2
Fast Ethernet Switch
User's Guide Connector Pinouts 18
Appendix B - Introduction to Your Network 16
Specifications 17 Appendix A -
Manual - Page 3
... to install and configure the Switch with . Installation
Everything you need to know to LAN & Ethernet Technologies
See Appendix B for more information. Fast EthernetSwitch
3
User's Guide
Specifications
The Switch's specifications at a glance.
FastEthernet Switch
Chapter Overview
Introduction
A general overview of switching benefits and the features of the Switch this manual accompanied...
Manual - Page 4
It further eliminates congestion problems inherent to reduce the congestion under heavy network loads.
The old shared-access Ethernet technology provides neither enough bandwidth nor predictable response time for expensive network equipment.
4
Fast Ethernet Switch
User's Guide Expensive routing equipment was used in the huge 10BASE-T Ethernet installed base. The new wave of ...
Manual - Page 7
... full. ♦ Supports Store & Forward architecture and performs
forwarding and filtering at non-blocking full wire speed. ♦ Broadcast Storming Filter function. ♦ Comprehensive array of LED indicators that communicate
the status of the switch and troubleshooting information. The Eight-port Switch User's Manual AC power cord
Fast EthernetSwitch
7
User's Guide Packing List
When...
Manual - Page 11
... MDIX
If connecting to a power supply and turned on the port.
The LED flashes when the switch detects packet collisions on . Fast EthernetSwitch
11
User's Guide
oPower
This LED comes on when the switch is connected to an uplink port of a hub or another switch, any of the switch's RJ-45...
Manual - Page 12
... is illuminated when the port is connected
to another working networked device. p Activity Status
TX: Transmit Data
RX: Receive Data
12
Fast Ethernet Switch
User's Guide The LEDs are identified by a corresponding array of three LEDs to a power supply and turned on.
n Port Status
Fast Ethernet Switch
100BASE-FX Ports
Each...
Manual - Page 13
thus the auto MDIX status does not apply to enable Half-Duplex mode for 100BASE-FX ports.
There is no auto MDIX for 100BASE-FX ports (Default setting). FastEthernet Switch
q Dip Switch
Full-Duplex: Toggle up to enable Full-Duplex mode for fiber 100BASE-FX ports; Half-Duplex: Toggle down to 100BASE-FX ports. Fast EthernetSwitch
13
User's Guide
Manual - Page 14
... Switch
This chapter presents step-by-step installation instructions for IEC 801-3, Level 2 (3V/M) field strength.
Specifically, the site you should place the Switch where it will ...the switch or the fan exhaust port on the rear of the switch.
14
Fast Ethernet Switch
User's Guide Surrounding electrical devices should be within 1.8meter (6 feet) of the switch. Make sure that the switch ...
Manual - Page 15
...) position.
Connecting to Power
FastEthernet Switch
Connect the supplied AC power cord to the receptacle on the rear of the switch
Fast EthernetSwitch
15
User's Guide
Manual - Page 16
...sure that it has a properly installed 100BASE-FX network interface card. All the non-fiber ports support 10BASE-T or 100BASE-TX with ...SC type connectors at both ends. Connecting to Your Network
Fast Ethernet Switch
10/100BASE-TX ports
Connect cables to computers or network segments into the RJ45 ports on the switch.
16
Fast Ethernet Switch
User's Guide...
Manual - Page 17
FastEthernet Switch
Specifications
Applicable Standards
10BASE-T, IEEE 802.3 100BASE-TX/FX, IEEE 802.3u
Ports 10/100BASE-TX or 100BASE-FX
Speed
100BASE-...
12 W
Operating Temperature
32 ~ 104 degrees F (0 ~ 40 degrees C)
Humidity
10 ~ 90%, non-condensing
Altitude
10,000 ft (3048 m)
Emissions
FCC part 15 Class A, CISPR Class A,
VCCI-I CE Mark
Safety
UL
Fast EthernetSwitch
17
User...
Manual - Page 19
... speed, price, ease of installation, and supportability.
As LAN...Guide LAN connects independent computers, file servers, printers, etc.
LAN
In order to reduce the expense on computer hardware and software and to easily share information, LAN technologies were developed for people to connect together and become increasingly complex, computer network has evolved as a very important part...
Manual - Page 20
...802.3. A number of other high-speed LAN technologies are installed with existing cabling infrastructure. It requires only minimal changes with...percent of all kinds of popular network protocols. Ethernet supports just about all Local Area networks are also available... of the future.
20
Fast Ethernet Switch
User's Guide The Institute of Electrical and Electronic Engineers (IEEE) define...
Manual - Page 21
... retain the existing 10Base-T cabling infrastructure, thus becomes the most compatible to share Ethernet. Other than supports higher data transfer speed, this technology also promises for use with cable 3,4,or 5 UPT cable. Fast EthernetSwitch
21
User's Guide Hub, also called repeater, only allows users to 10Base-TX. Among three of them, 100Base...
TRENDnet TE100-S86FX Reviews
We have not received any reviews for TRENDnet yet.