Instruction Manual
Page 2
... the convenient Auto Scanning and Manual Scanning modes. The Network Cable Tester verifies continuity of pre-installed premise wiring. Everything comes packaged in two modular units, a master unit and a remote terminator. This tester is also included and individual pins/wires can be selected to expand ... Network professional. The Network Cable Tester comes complete with shielded connectors, which enables the testing of coax BNC network and a RJ45 to RJ45 adapters for testing patch panel and RJ45 network wall plates. It comes with BNC to RJ45 patch cord for testing...
... the convenient Auto Scanning and Manual Scanning modes. The Network Cable Tester verifies continuity of pre-installed premise wiring. Everything comes packaged in two modular units, a master unit and a remote terminator. This tester is also included and individual pins/wires can be selected to expand ... Network professional. The Network Cable Tester comes complete with shielded connectors, which enables the testing of coax BNC network and a RJ45 to RJ45 adapters for testing patch panel and RJ45 network wall plates. It comes with BNC to RJ45 patch cord for testing...
Instruction Manual
Page 3
Auto - DOING SO WHERE VOLTAGE IS PRESENT MAY DAMAGE THE TESTER. Tests Lan, Telcom, UTP/STP and coax BNC cables. 6. scan and manual step testing. 4. A. FEATURES: 1. Tone feature easily locates remote cable ends. CAUTION: NOT FOR USE ON LIVE CIRCUITS. Tests pin to pin connection of the cable to be tested 2 LOOP-BACK TEST 1. Checks for opens shorts and cross connected wires. 5. To test patch cords, plug both ends of cables. 2. For loop-back and remote testing. 3.
Auto - DOING SO WHERE VOLTAGE IS PRESENT MAY DAMAGE THE TESTER. Tests Lan, Telcom, UTP/STP and coax BNC cables. 6. scan and manual step testing. 4. A. FEATURES: 1. Tone feature easily locates remote cable ends. CAUTION: NOT FOR USE ON LIVE CIRCUITS. Tests pin to pin connection of the cable to be tested 2 LOOP-BACK TEST 1. Checks for opens shorts and cross connected wires. 5. To test patch cords, plug both ends of cables. 2. For loop-back and remote testing. 3.
Instruction Manual
Page 4
..., 3 Set the power switch to ON. (a) Auto Scan Mode: Press and release the AUTO button, the LED in the TX row will advance the LED to the next one in relation to the TX row, to indicate the pin being tested. Any subsequent press of LED will light (or not), in sequence (1,2,..., shield and repeat), to Manual Scan...
..., 3 Set the power switch to ON. (a) Auto Scan Mode: Press and release the AUTO button, the LED in the TX row will advance the LED to the next one in relation to the TX row, to indicate the pin being tested. Any subsequent press of LED will light (or not), in sequence (1,2,..., shield and repeat), to Manual Scan...
Instruction Manual
Page 5
please check or replace your battery. 3. ii) If a LED is lit or if TX & RX LEDs are unlit simultaneouslyThis indicates a short . This may indicate an open or a burnt out LED. See RX and TX LED for test result. 4 To test BNC, USB or other cable configurations please use the appropriate adapters and follow the above procedure. straight, reverse, miss-wire...etc.) can be determined. iii) If no LED will light - i) If more than one LED from the same row is skipped -
please check or replace your battery. 3. ii) If a LED is lit or if TX & RX LEDs are unlit simultaneouslyThis indicates a short . This may indicate an open or a burnt out LED. See RX and TX LED for test result. 4 To test BNC, USB or other cable configurations please use the appropriate adapters and follow the above procedure. straight, reverse, miss-wire...etc.) can be determined. iii) If no LED will light - i) If more than one LED from the same row is skipped -
Instruction Manual
Page 6
...and repeat), to indicate status. 4. C. B. The TX LED will light (or not) in the middle of the test cable to Auto scan. REMOTE TEST 1. Set the power switch to ON and set the tester to the MASTER unit marked TX . 2. Use a patch cord (included) if the test cable terminates into a wall jack or patch...cable to quickly isolate and locate a hidden cable or a break (open) in relation to the Master tester unit to indicate the pins being tested. SENDING TONE TO IDENTIFY CABLES Using Network cable tester s tone generator along with Net Probe or any other cable configurations, please...
...and repeat), to indicate status. 4. C. B. The TX LED will light (or not) in the middle of the test cable to Auto scan. REMOTE TEST 1. Set the power switch to ON and set the tester to the MASTER unit marked TX . 2. Use a patch cord (included) if the test cable terminates into a wall jack or patch...cable to quickly isolate and locate a hidden cable or a break (open) in relation to the Master tester unit to indicate the pins being tested. SENDING TONE TO IDENTIFY CABLES Using Network cable tester s tone generator along with Net Probe or any other cable configurations, please...
Instruction Manual
Page 7
...TEST button to select a pin to AUTO scan, a sequencing tone is supplied on shield position. 2. Simply trace along the cable from the master unit using the tone as a guide, towards the remote end of the test cable until the tone disappeared will indicate the location of the 8 pins, ...shield and BNC cable. Master unit and remote unit. 2. D. PRODUCT PACKAGE 1. Set the power switch to BNC adapters. 6 cable 1. RJ45 to...
...TEST button to select a pin to AUTO scan, a sequencing tone is supplied on shield position. 2. Simply trace along the cable from the master unit using the tone as a guide, towards the remote end of the test cable until the tone disappeared will indicate the location of the 8 pins, ...shield and BNC cable. Master unit and remote unit. 2. D. PRODUCT PACKAGE 1. Set the power switch to BNC adapters. 6 cable 1. RJ45 to...
Instruction Manual
Page 8
... X 26 ) 2. Tone freq. 600 800 HZ 7 Carrying pouch. 5. E. Please make sure the battery is weak or fails, the LED indicators will be dim or fail to light. Operating temp. 0 C 45 C 3. RODUCTION SPECIFICATION 1. RJ45 to use the tester for any extended period. Please take out the battery if you do not need to RJ45 patch cord. 4. User guide. One DC 9V...
... X 26 ) 2. Tone freq. 600 800 HZ 7 Carrying pouch. 5. E. Please make sure the battery is weak or fails, the LED indicators will be dim or fail to light. Operating temp. 0 C 45 C 3. RODUCTION SPECIFICATION 1. RJ45 to use the tester for any extended period. Please take out the battery if you do not need to RJ45 patch cord. 4. User guide. One DC 9V...