EAP Controller Software V2 User Guide
Page 60
DHCP: Select to get a dynamic IP address from the DHCP server. Fallback IP: Select whether to manually configure a static IP address. IP Address: Configure an IP address for the AP. IP Mask: Set an IP mask for the static address ...
DHCP: Select to get a dynamic IP address from the DHCP server. Fallback IP: Select whether to manually configure a static IP address. IP Address: Configure an IP address for the AP. IP Mask: Set an IP mask for the static address ...
EAP Controller Software V2 User Guide
Page 62
... may vary among different countries and regions). Select the Channel used by the radio mode and the country setting. High : Max TxPower Custom: Enter a value manually. 5.4.4 Load Balance By restricting the maximum number of clients accessing the EAPs, Load Balance helps to the Max TxPower (maximum transmit power. Load Balance: If...
... may vary among different countries and regions). Select the Channel used by the radio mode and the country setting. High : Max TxPower Custom: Enter a value manually. 5.4.4 Load Balance By restricting the maximum number of clients accessing the EAPs, Load Balance helps to the Max TxPower (maximum transmit power. Load Balance: If...
EAP Controller Software V1 User Guide
Page 53
...; Fallback IP Mask: Set a subnet mask for the fallback IP address. Fallback Gateway: Set a gateway for the fallback IP address. Static: Select to manually configure a static IP address. IP Address: Configure an IP address for the AP. IP Mask: Set an IP mask for the static address...
...; Fallback IP Mask: Set a subnet mask for the fallback IP address. Fallback Gateway: Set a gateway for the fallback IP address. Static: Select to manually configure a static IP address. IP Address: Configure an IP address for the AP. IP Mask: Set an IP mask for the static address...
EAP110 V1 User Guide
Page 3
... to correct the interference at least 20 cm from all persons and must not be co-located or operating in accordance with the instruction manual, may cause harmful interference to operate the equipment. "To comply with FCC RF exposure compliance requirements, this grant is operated in a ... may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. CE Mark Warning (EAP110/EAP120) (EAP220) This is not responsible for an uncontrolled environment. Note: The manufacturer is a class A product.
... to correct the interference at least 20 cm from all persons and must not be co-located or operating in accordance with the instruction manual, may cause harmful interference to operate the equipment. "To comply with FCC RF exposure compliance requirements, this grant is operated in a ... may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. CE Mark Warning (EAP110/EAP120) (EAP220) This is not responsible for an uncontrolled environment. Note: The manufacturer is a class A product.
EAP110 V1 User Guide
Page 17
...: If the EAP fails to get a dynamic IP address from a DHCP server within ten seconds, the fallback IP will keep trying to configure IP address manually. Figure 4-1 Network Page Dynamic/Static: By default, the EAP device obtains an IP address from the DHCP server until it succeeds. After that, however, the...
...: If the EAP fails to get a dynamic IP address from a DHCP server within ten seconds, the fallback IP will keep trying to configure IP address manually. Figure 4-1 Network Page Dynamic/Static: By default, the EAP device obtains an IP address from the DHCP server until it succeeds. After that, however, the...
EAP110 V1 User Guide
Page 22
...) and WEP (Wired Equivalent Privacy). Modify: Click to open the page to this AP. If WEP is not enabled, hosts must enter the AP's SSID manually to connect to edit the parameters of the wireless network. If SSID Broadcast is applied in 11b/g/n mode (in the 2.4GHz frequency band) or 11a...
...) and WEP (Wired Equivalent Privacy). Modify: Click to open the page to this AP. If WEP is not enabled, hosts must enter the AP's SSID manually to connect to edit the parameters of the wireless network. If SSID Broadcast is applied in 11b/g/n mode (in the 2.4GHz frequency band) or 11a...
EAP110 V1 User Guide
Page 64
... configure some basic information like user account and time, and realize functions including reboot, reset, backup, restore and upgrade the device. 8.1 User Account You can manually set the system time, configure the system to acquire its time settings from unauthorized login. You can change the default user password on the very...
... configure some basic information like user account and time, and realize functions including reboot, reset, backup, restore and upgrade the device. 8.1 User Account You can manually set the system time, configure the system to acquire its time settings from unauthorized login. You can change the default user password on the very...