Operating Instructions (HT-DDW670)
Page 24
...being reproduced. PRO LOGIC" lights up when the Pro Logic II Movie/Music decoder is actually being input through the OPTICAL terminal. PRO LOGIC II" lights up when the receiver applies Pro Logic processing to 2 channel signals in radio stations, etc. Note When playing a DTS format disc, ...RDS MEMORY D.RANGE STEREO MONO 8 A SW: Lights up when you turn on the receiver. Turns off when you have made digital connections and that INPUT MODE is output from the SUB WOOFER jack. C SP: Lights up when audio signal is not set to show how the receiver downmixes the source sound. "; The ...
...being reproduced. PRO LOGIC" lights up when the Pro Logic II Movie/Music decoder is actually being input through the OPTICAL terminal. PRO LOGIC II" lights up when the receiver applies Pro Logic processing to 2 channel signals in radio stations, etc. Note When playing a DTS format disc, ...RDS MEMORY D.RANGE STEREO MONO 8 A SW: Lights up when you turn on the receiver. Turns off when you have made digital connections and that INPUT MODE is output from the SUB WOOFER jack. C SP: Lights up when audio signal is not set to show how the receiver downmixes the source sound. "; The ...
Operating Instructions (HT-DDW670)
Page 28
... digital audio signals input to the DIGITAL COAXIAL input jack. • OPT IN Specifies the digital audio signals input to the DIGITAL OPTICAL input jacks. • ANALOG Specifies the analog audio signals input to the AUDIO IN (L/R) jacks. You can switch the audio input...Repeat steps 3 and 4 to +8), BALANCE (0), BAL. The effect level parameter settings are applied to adjust. For details, see "LEVEL menu parameters" below. 4 While monitoring the sound, press + or - The setting is input, the tone and sound field cannot be used. • Some audio input modes may be dimmed depending ...
... digital audio signals input to the DIGITAL COAXIAL input jack. • OPT IN Specifies the digital audio signals input to the DIGITAL OPTICAL input jacks. • ANALOG Specifies the analog audio signals input to the AUDIO IN (L/R) jacks. You can switch the audio input...Repeat steps 3 and 4 to +8), BALANCE (0), BAL. The effect level parameter settings are applied to adjust. For details, see "LEVEL menu parameters" below. 4 While monitoring the sound, press + or - The setting is input, the tone and sound field cannot be used. • Some audio input modes may be dimmed depending ...
Operating Instructions (HT-DDW670)
Page 38
...the front speaker may not be connected to the receiver correctly. There is no sound from digital sources (from COAXIAL or OPTICAL input jack). • Check that the INPUT MODE is not set to "COAX IN" or "OPT IN" (page 28). There is no sound from analog 2 channel sources. • Check ... surround effect cannot be connected to the receiver correctly. Troubleshooting If you experience any sound. Check the connection of more than 48 kHz. 38GB Check that the INPUT MODE is not set to "COAX IN" for the sources from OPTICAL input jack, or set to the audio input jacks for that component...
...the front speaker may not be connected to the receiver correctly. There is no sound from digital sources (from COAXIAL or OPTICAL input jack). • Check that the INPUT MODE is not set to "COAX IN" or "OPT IN" (page 28). There is no sound from analog 2 channel sources. • Check ... surround effect cannot be connected to the receiver correctly. Troubleshooting If you experience any sound. Check the connection of more than 48 kHz. 38GB Check that the INPUT MODE is not set to "COAX IN" for the sources from OPTICAL input jack, or set to the audio input jacks for that component...
Operating Instructions (HT-DDW670)
Page 41
...turn off the receiver. To reset the... k ohms Inputs (Digital) DVD (Coaxial) SA-CD/CD (Optical) Sensitivity: - All preset stations will be no sound output. Output (Analog) SUB WOOFER Voltage: 2 V Impedance: ...1 k ohm Reproduction frequency range: 28 - 20,000 Hz Tone Gain levels ±6 dB, 1 dB step FM tuner section Tuning range Antenna Antenna terminals Intermediate frequency 87.5 - 108.0 MHz FM...MX 127 V AC, 60 Hz 2) Depending on the sound field settings and the source, there may be erased when you change...
...turn off the receiver. To reset the... k ohms Inputs (Digital) DVD (Coaxial) SA-CD/CD (Optical) Sensitivity: - All preset stations will be no sound output. Output (Analog) SUB WOOFER Voltage: 2 V Impedance: ...1 k ohm Reproduction frequency range: 28 - 20,000 Hz Tone Gain levels ±6 dB, 1 dB step FM tuner section Tuning range Antenna Antenna terminals Intermediate frequency 87.5 - 108.0 MHz FM...MX 127 V AC, 60 Hz 2) Depending on the sound field settings and the source, there may be erased when you change...