Sony CPD-E500 - 21" CRT Display Support and Manuals
Get Help and Manuals for this Sony item
This item is in your list!
View All Support Options Below
Free Sony CPD-E500 manuals!
Problems with Sony CPD-E500?
Ask a Question
Free Sony CPD-E500 manuals!
Problems with Sony CPD-E500?
Ask a Question
Popular Sony CPD-E500 Manual Pages
Operating Instructions - Page 2
... has been tested and found to comply with the instructions, may not cause harmful interference, and (2) this device must accept any changes or modifications not expressly approved in a residential installation.
Declaration of Conformity
Trade Name: Model No.: Responsible Party: Address: Telephone No.:
Sony CPD-E500 Sony Electronics Inc. 1 Sony Drive, Park Ridge, NJ. 07656 USA 201-930-6970...
Operating Instructions - Page 3
... the quality of the picture (SCREEN 11 Adjusting the color of Sony Corporation.
• Macintosh is a U.S.
Precautions 4 Identifying parts and controls 5
Setup 6
Step 1: Connect your screen (damper wires 15 On-screen messages 15 Trouble symptoms and remedies 16 Self-diagnosis function 18
Specifications 18
Appendix i
Preset mode timing table i
3 registered
mark. • All...
Operating Instructions - Page 4
...
draperies, etc.) that it horizontally or vertically. The equipment should be installed near the monitor. If you transport this monitor will not conform to discharge.
• After the power is turned ...Hold the monitor at the bottom with a soft cloth. If you turn it is demagnetized (degaussed) for repair or shipment, use any type of the monitor when you tilt the monitor up ...
Operating Instructions - Page 5
...in green when the monitor is turned on, and either
11 21 31 41 51
flashes in green and orange, or lights up in orange when the
monitor is in parentheses for...resets the adjustments to the factory settings.
4 AC IN connector (page 6) This connector provides AC power to the monitor, including brightness and contrast adjustments.
Sync
14
V. Identifying parts and controls
See the pages in...
Operating Instructions - Page 6
...8226; Setup Disk (1) • Warranty card (1) • Notes on cleaning the screen's surface (1) • This instruction manual (1)
Step 1: Connect your computer
Turn off , first connect the power cord to the monitor, then... cord
With the monitor and computer switched off the monitor and computer before connecting the cable.
Note Do not touch the pins of pins or models other version of ...
Operating Instructions - Page 7
... completely seated in the correct bus slot. • If you are replacing an old monitor with this monitor's model name as the monitor type in Windows NT4.0 is complete. If your monitor is different from the supplied Setup Disk onto your monitor, install the new model information file from Windows 95/98 and does not involve the selection of your PC. Refer...
Operating Instructions - Page 10
... for horizontal adjustment, or for the current input signal.
1 Press the center of the control button again. Adjusting the size of the picture (SIZE)
This setting is stored in memory for vertical adjustment. Then move the control button m/M to highlight SIZE and press the center of the control button.
Operating Instructions - Page 11
...the control button to adjust the quality of the control button. Adjusting the convergence (CONV)
The CONV settings allow you see red or blue shadows around letters or lines, adjust the convergence. If you to ...appears on the screen.
3 First move the control button These settings are stored in memory for all input signals.
1 Press the center of the picture by controlling the ...
Operating Instructions - Page 12
The main MENU appears on the screen.
3 Move the control button These settings are stored in memory for matching the monitor's color to a printed picture's colors. The COLOR menu appears on the screen.
2 Move the... center of the control button. Adjusting the color of the picture (COLOR)
The COLOR settings allow you to highlight COLOR and press the center of the control button again.
Operating Instructions - Page 13
... in the COLOR menu. CO L OR EASY
E PERT s RGB
: 56
: 7 6 FOR s RGB
Additional settings (OPTION)
You can manually degauss (demagnetize) the monitor, change the brightness ( ) and contrast (6), see page 9.
Note Your computer and other connected products (such as a printer), must set your computer to the sRGB profile and adjust the brightness ( ) and contrast (6) to...
Operating Instructions - Page 14
...signal is set by this monitor ensures that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in the monitor's frequency ...Windows users, check your video board manual or the utility program which comes with your computer enters a power saving mode, the input signal is displayed on the screen. Resetting the adjustments
This monitor...
Operating Instructions - Page 15
... so that no signal is not supported by allowing more information, see "Trouble symptoms and remedies" on the screen. The aperture grille is something wrong with this section.
Damper wires
On-screen messages
If there is the essential element that makes a Trinitron picture tube unique by the monitor's specifications.
3 The remedies CHANGE SIGNAL TIMING...
Operating Instructions - Page 16
...) if the following recommendations do the following . Install the Setup Disk (page 7) and select this monitor, reconnect the old monitor and do not resolve the problem. Even if the frequency is too narrow for the monitor. Decrease the moire
cancellation effect or set CANCEL MOIRE to the connected equipment's instruction manual. Symptom
Check these items
No picture
If the...
Operating Instructions - Page 17
the following information. • Model name: CPD-E500 • Serial number • Name and specifications of video cable extensions and/or video switch boxes. • Check that generates a magnetic field,
such as a speaker, near the monitor, or if you place equipment that all plugs are firmly seated in their sockets.
• Adjust the size (page 10...
Operating Instructions - Page 18
... to note the model name and serial number of the monitor will either light up green, the monitor is working properly. If the 1 (power) indicator is lit in orange, the computer is a potential monitor failure. Reconnect the video input cable and check the condition of your authorized Sony dealer of the monitor's condition. Specifications
CRT
Viewable image size...
Sony CPD-E500 Reviews
Do you have an experience with the Sony CPD-E500 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Sony yet.
Earn 750 points for your review!