Seagate STD224000N - DAT Scorpion 24 Tape Drive Support and Manuals
Get Help and Manuals for this Seagate item
View All Support Options Below
Free Seagate STD224000N manuals!
Problems with Seagate STD224000N?
Ask a Question
Free Seagate STD224000N manuals!
Problems with Seagate STD224000N?
Ask a Question
Most Recent Seagate STD224000N Questions
Only Reads Its Own Tapes
std224000n operating on unix 5.0 only reads its own tapes
std224000n operating on unix 5.0 only reads its own tapes
(Posted by roberthines 12 years ago)
Popular Seagate STD224000N Manual Pages
Installation Manual - Page 3
Seagate DAT Drive Installation Manual
Contents
FCC notice
Introduction
1
Before you begin
1
SCSI cables and connectors
2
Installing an internal DAT drive
3
Configuring an internal DAT drive
3
Mounting an internal DAT drive
10
Connecting power and interface cables
10
Installing an external DAT drive
11
Configuring an external DAT drive
11
Connecting the SCSI interface cable
12...
Installation Manual - Page 4
... Commission helpful: How to provide reasonable protection against such interference in a residential installation. Seagate DAT Drive Installation Manual
FCC notice
This equipment generates and uses radio frequency energy and, if not installed and used in strict accordance with the manufacturer's instructions, may find the following measures:
• Reorient or relocate the receiving antenna...
Installation Manual - Page 5
... identifies the Seagate DAT drive models covered by this manual and the tape formats that support the DDS (digital data storage), DDS-DC (digital data storage data compression), DDS-2 and DDS-3 tape formats.
To avoid data loss, you begin
!
Native capacity is one half these values. Caution. Seagate DAT Drive Installation Manual
1
Introduction
This installation manual contains...
Installation Manual - Page 6
... following precautions to avoid electrostatic damage to your internal tape drive.
• Do not remove the drive from your body.
• Hold the drive only by its SCSI host adapter.
The external DAT drive provides two 50-pin, shielded connectors (ANSI Alternative 2) on top of the drive. Seagate DAT Drive Installation Manual
2
! A 50-conductor flat cable or a 25-signal twisted...
Installation Manual - Page 7
... features.
Connecting power and interface cables
Internal DAT drives come in two configurations, for mounting in the drive shell.
® Note. These reserved switches are set using a bank of dipswitches on each switchbank. Configuring an internal DAT drive
Before you install the tape drive in Figures 1 and 2. DDS-3 drives have two additional reserved dip switches on the underside of...
Installation Manual - Page 9
... ID 0 1 2 3 4 5 6 7
® Note. The drive must be turned OFF then ON or a SCSI Bus Reset must be received for each switch are shown in detail on self-test diagnostics are described in Figure 3 (only DDS-3 drives have switches S9 and S10). These settings are disabled.
Seagate DAT Drive Installation Manual
5
Factory-default settings for switch settings to take effect.
Installation Manual - Page 10
... both MRS and non-MRS 4-mm media. The function of the S6 switch can cause dataintegrity problems.
The S4 switch enables or disables media-recognition system (MRS) mode. If S4 is still generated by the drive.
Seagate DAT Drive Installation Manual
6
SCSI ID switches (switches S1 through S3)
The three switches S1 through S3 correspond to...
Installation Manual - Page 11
... (about 5 seconds). Seagate DAT Drive Installation Manual
7
Power-on self-test enable/disable (switch S8)
The S8 switch enables or disables execution of power-on self-test diagnostics when the drive is ON, the drive responds to control SCSI bus termination and terminator power. Jumper settings
The configuration jumpers are only present on 3.5-Inch internal drives
Jumper Block
Pin 1
SCSI...
Installation Manual - Page 12
... are :
• Terminator power is disabled. • Active termination is disabled. The default settings are described in Figure 6 below. Seagate DAT Drive Installation Manual
8
Figure 5 Location of jumpers for 5.25-inch drives
Jumper Block
Pin 1
SCSI Connector
Power Connector
Settings for internal DAT drives
15 13 11 9 7 5 3 1 16 14 12 10 8 6 4 2
SCSI ID
ActiveTerminator Enabled...
Installation Manual - Page 13
... page 5.) Seagate DAT Drive Installation Manual
9
Enabling SCSI termination
Active SCSI termination is disabled as shown in case the terminator power is installed, be careful not to short the TERMPWR signal to pins 1 through 6. Caution. If the jumper is shorted.
Remote SCSI Address Selection
You can enable terminator power if needed for ID selection, set switches S1...
Installation Manual - Page 15
... + and - then set the SCSI ID for Seagate external DAT drives:
• The drive reads or writes both MRS and non-MRS
4-mm media.
• Parity checking is disabled. • DDS-DC data compression is supplied to
models that support data compression)
• The power-on self-test diagnostics of the external drive. External drive installation involves three main...
Installation Manual - Page 20
...drive heads after every 25 hours of data retries (beyond a predefined DDS error threshold). First, clean the drive heads using an approved DDS DAT cleaning cartridge (such as the Seagate Model... this signal, remove the tape and clean the tape heads using an approved DDS DAT cleaning cartridge, such as the Seagate Model 91301). Seagate DAT Drive Installation Manual
16
Cartridge status LED
The...
Installation Manual - Page 23
...; Model M312000 (125 meters; DDS-3 only)
DDS-2 and DDS-3 DAT drives also recognize 120-meter MP+ cartridges and other MRS cartridges when MRS is received.
® Note. Seagate DAT Drive Installation Manual
19
blank tape takes about 30 seconds. The initialization will restart from the beginning the next time a WRITE command is enabled. DAT cartridge compatibility
Seagate DAT drives are...
Installation Manual - Page 25
... cartridge. The slowly flashing LED does not indicate a loss of cleaning tape is used up, the drive ejects the tape without completing a cleaning operation.
Seagate DAT Drive Installation Manual
21
® Note. If cleaning the head does not correct the flashing LED condition, replace the cartridge. Each time the cleaning cartridge is loaded, a new, unused portion of data, nor...
Installation Manual - Page 26
... bulletin board system, available 24 hours daily. SeaNET: Seagate's World Wide Web home page- Set your DAT drive, contact one help, you experience problems installing or using your modem to 9,600 baud, eight data bits, no parity and one stop bit (8-N-1).
http://www.seagate.com
Seagate CompuServe Forum: Online technical support for users of the technical support services listed below.
Seagate STD224000N Reviews
We have not received any reviews for Seagate yet.