Samsung SRP-270AP - B/W Dot-matrix Printer Support and Manuals
Get Help and Manuals for this Samsung item
View All Support Options Below
Free Samsung SRP-270AP manuals!
Problems with Samsung SRP-270AP?
Ask a Question
Free Samsung SRP-270AP manuals!
Problems with Samsung SRP-270AP?
Ask a Question
Popular Samsung SRP-270AP Manual Pages
Operation Manual - Page 1
SRP-270 SERIES
1 STATION PRINTER
Operator's Manual
All specifications are subjected to change without notice
Operation Manual - Page 2
...SRP-270 series. U.S. Operation of this manual carefully before you should turn the printer "OFF", before using your local service provider.
Caution
Some semiconductor devices are designed to Part 15 of the printer...if not installed and used according to the instruction manual, may cause harmful interference to receive print data even during printing. 5. You should turn the printer OFF, ...
Operation Manual - Page 3
...TO THE PRINTER 6 2-2. SETTING THE DIP SWITCHES 13
CHAPTER 5. CODE TABLE 18
CHAPTER 8. CONTROL COMMANDS LIST 25
APPENDIX A 29 CONNECTORS 29 Interface Connector 30 Drawer Connector 32
APPENDIX B 33 SPECIFICATION 33
APPENDIX C 34 REMOVING JAMMED PAPER 34
3 HEXADECIMAL DUMPING 16
CHAPTER 6. Table of Contents
CHAPTER 1. UNPACKING 4 1-1. INSTALLING THE ROLL PAPER 8 3-1. RIBBON...
Operation Manual - Page 8
... the roll paper
3-1. Contact your dealer or place of the ribbon behind the Print Head.
3). NOTE : Malfunctions and other problems may be voided if other than specified ribbon cassettes are used . During inserting the ribbon cassette, turn the knob clockwise to
make sure the ribbon moves freely in the printer. Ribbon Cassette Installation
1). Before inserting the ribbon cassette, turn...
Operation Manual - Page 9
..., make sure that matches the printer's specifications.
1). To use roll paper that the printer has no un-printed data. " SRP-270 A/C : 1Ply Paper # SRP-270 D : 2Ply Paper
3).
Open the printer cover and remove the used paper roll core if there is one. Roll Paper Installation
Be sure to use a new roll paper, unroll the paper and tear off the end of the paper correctly.
9 This data may...
Operation Manual - Page 10
Put the roll paper on the paper holder and insert the paper in the printer.
4). " SRP-270 A/C : 1Ply Paper # SRP-270 D : 2Ply Paper
10
Operation Manual - Page 14
... the word length is 7 bits, you can not parity check OFF status.
14 Serial Interface (RS-232C/RS-485) Specification
DIP Switch 1 Setting
SW
FUNCTION
1 2
Emulation Selection
3
Auto-Cutter
4
FONT SPACE
5
Function for
6
service
7
Engineer
8
RESERVED
ON
OFF
Refer to the following table
Enable 2
Disable 3
Emulation mode selection
SW - 1 OFF OFF ON
SW...
Operation Manual - Page 15
... Interface Specification
DIP Switch 1 Setting
SW
FUNCTION
1 2
Emulation Selection
3
Auto-Cutter
4
FONT SPACE
5
Function for
6
service
7
Engineer
8
RESERVED
ON
OFF
Refer to the following table
Enable 2
Disable 3
DEFAULT OFF OFF OFF OFF OFF OFF
Emulation mode selection
SW - 1 OFF OFF ON
SW - 2 OFF ON OFF
MODE Epson Citizen Star
Dip Switch 2 Setting
SW
FUNCTION...
Operation Manual - Page 16
.... l Insufficient print data to see exactly what data is printed for each code that correspond to the printer. When the printing finishes, turn on the printer, then the printer enters the hexadecimal dump mode. 4. l During the hex dump, all the
codes it receives in hexadecimal format along with a guide section to the printer. Chapter 5.
Set DIP switch 2-2 On. 3.
Operation Manual - Page 17
... self-test checks whether the printer has any problems. If the printer does not function properly, contact your dealer.
1. Make sure paper roll has been installed properly. 2. The self-test begins. 3.
The printer prints a pattern using the built-in character set.
6. The self-test automatically ends after printing the following ,
and pause (The PAPER LED light blinks). Press...
Operation Manual - Page 18
Chapter 7. Code Table
The following pages show the character code tables. Page 0 ( PC437 : USA, Standard Europe) ( International Character Set : USA ) 18 For example, 4A = J. To find the character corresponding to a hexadecimal number, count across the top of the table for the left digit and count down the left column of the table for the right digit.
Operation Manual - Page 32
... name
1
Frame ground
2
Drawer kick-out drive signal 1
3
Drawer open/close signal
4
+24V
5
Drawer kick-out drive signal 2
6
Signal ground
Direction Output Input Output -
* SRP-270 Series Model Listing Model Name : SRP-27xyz
x 0 Ivory 5 Dark Gray
y A Basic C Basic
+ Auto cutter D Basic
+ Auto cutter + Spool
32
Blank S P U
z RS-232C RS-485 IEEE-1284 USB USB Interface...
Operation Manual - Page 33
...; É~ 50¡ É( 23¢ µ~ 122¢ µ)
10% ~ 95%
33 Appendix B
Specification
Printer Ribbon
Printing method Number of head pin Printing direction Lines per second Characters per line Ribbon type Color Ribbon life
Paper
Adapter Auto Cutter ETC
Paper type Paper width
Roll diameter Thickness Overall dimensions Weight Types Cutter type Cutting width Cutting thickness...
Operation Manual - Page 34
CAUTION : The printer head becomes very hot during printing.
Allow it to be cool before you reach into the printer.
34 Appendix C
Removing Jammed Paper 1) Open the printer cover 2) Raise the auto cutter unit by lifting the knob lock. 3) Remove the ribbon cassette. 4) Loosen the manual screw. 5) Remove the head cover.
Operation Manual - Page 36
Insert a screw driver into the hole at the bottom side of auto cutter unit as shown followed picture, and turn the gear inside the cutter unit to move the cutter blade to its normal position. NOTE : If you are troubled with reloading the paper, the cutter blade may not be in its normal position.
36
Samsung SRP-270AP Reviews
We have not received any reviews for Samsung yet.