Ryobi WS7211 Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi WS7211 manuals!
Problems with Ryobi WS7211?
Ask a Question
Free Ryobi WS7211 manuals!
Problems with Ryobi WS7211?
Ask a Question
Ryobi WS7211 Videos
Ryobi WS721, WS7211, and WS7211K 7" Wet tile saw setup and operation
Duration: 18:36
Total Views: 19,747
Duration: 18:36
Total Views: 19,747
Popular Ryobi WS7211 Manual Pages
User Manual - Page 2
... Warranty...2 General Safety Rules...3 - 4 Specific Safety Rules...4 Symbols...5 Electrical...6 - 7 Features...7 Assembly...8 - 9 Operation...9 - 11 Maintenance...12 Figure numbers (illustrations)...13 - 17 Parts Ordering / Service...Back page
INTRODUCTION
This product has many features for direct...
User Manual - Page 3
...manual for better and safer performance. These cords are removed from receptacle. Form habit of the tool, a guard or other part that it is unintentionally contacted.
CHECK DAMAGED PARTS... the saw 's applications and limitations as well as the specific potential ...repaired or replaced by removing starter keys.
DON'T FORCE TOOL. TURN THE POWER OFF. Follow instructions...
User Manual - Page 4
... TURNED OFF. NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Watch what you loan someone this manual or addendums. Use of your saw or workpiece before operating. Have defective switches replaced by an authorized service center to them these instructions too.
4 - Instructions for which it will interfere with safe operation BEFORE performing any work and that are...
User Manual - Page 5
...related to rain or use in damp locations.
Wet Conditions Alert
Do not expose to an injury hazard, such as a situation that may result in death or serious injury. Read The Operator's Manual
To reduce the risk of these symbols will ... a potential personal injury hazard. Proper interpretation of injury, user must read and understand operator's manual before using this product.
User Manual - Page 6
... use an extension cord that is equipped with a qualified electrician or service personnel if the grounding instructions are intended for a greater distance. An undersized extension cord will not fit the outlet, have 3-prong grounding plugs and 3-pole receptacles that is properly installed and grounded in GFCI protection and may not be too light...
User Manual - Page 7
.... FEATURES
PRODUCT SPECIFICATIONS
Wheel Diameter 7 in .
TILE CUTTING WHEEL - Failure to heed this tool. Beveled 22.5° and 45° cuts can be obtained. ON/OFF SWITCH - Rip guide is included with your local retailer.
Rip Capacity (tile size 16 in . A 7 in . MITER GUIDE - This saw . Disconnect the fuse or circuit breaker that part of the cord...
User Manual - Page 8
... will come in serious personal injury. Use of the saw Tile cutting wheel Bevel table Splash hood with this product if any parts are not assembled to prevent the wheel from securing the wheel on the Loose Parts List are replaced. PACKING LIST
Tile saw .
Never use this tool. ASSEMBLY
UNPACKING
See Figure 4, page 14. Larger wheels will prevent...
User Manual - Page 9
.... Replace bevel table. INSTALLING THE MITER GUIDE
See Figure 8, page 15. Slide miter guide onto rip guide from front. Adjust rip guide to desired position...INSTALLING THE OVERFLOW DRAIN
See Figure 9, page 15. Remove bevel table. Locate hole on front and rear of table, to set rip guide to fill line. To change reservoir water: Unplug tile saw...
User Manual - Page 10
...part of the cutting wheel before turning on the saw .
Turn the on /off switch to the ON position. Let the cutting wheel build up to full speed and wait for
the wheel to get wet....
A common problem when cutting tile is back on track. If the tile is shiny and hard-to-mark, place masking tape on front and rear of table, to set rip guide to turn the saw turned OFF, pull...
User Manual - Page 11
...Set the rip guide to desired width, and tighten the knob to secure in place.
Adjust miter guide to get wet before moving the material into 22.5° angle. Use second set...material is made , turn the saw OFF. This time overcut the other...guide and slide miter guide along rip guide.
NOTE: Make sure bevel table is locked firmly in place before removing any part of tile...
User Manual - Page 12
...serious injury. Do not use wheel with your local dealer. WARNING:
Do not at your saw. Chemicals can damage, weaken or destroy plastic which may result in .
WARNING:
Do not... lubricated with ANSI Z87.1.
TILE CUTTING WHEEL
For maximum performance and safety, it is recommended that you use only identical Ryobi replacement parts. MAINTENANCE
WARNING:
When servicing, use the 7 in serious...
User Manual 2 - Page 3
...Assembly (Incl. RYOBI TILE SAW - PARTS LIST FOR FIGURE A
Key Part Key Part
No. No. Key No. 34 1
34 080009019011
O-Ring (D24.45 mm x D2.5 mm 1
3 MODEL NUMBER WS7211
The model...1 Wrench (B 1
Operator's Manual 1
33 080009019010
Overflow Drain Assembly (Inc. Always mention the model number in all correspondence regarding your TILE SAW or when ordering repair parts. Key Nos. 48, 52...
User Manual 2 - Page 4
MODEL NUMBER WS7211
MOTOR
CAPACITOR
GRAY
BLUE GRAY
WHITE GRAY
BLUE
BLACK
BLACK WHITE
WHITE
SWITCH
WIRING DIAGRAM
4
POWER CORD RYOBI TILE SAW -
Ryobi WS7211 Reviews
We have not received any reviews for Ryobi yet.