Ryobi P506 Support and Manuals
Popular Ryobi P506 Manual Pages
Repair Sheet - Page 3
... WARNING LABEL 1
49 520177001 EDGE GUIDE KNOB 1
983000535 OPERATOR'S MANUAL
06-01-07
(REV:04)
* Standard Hardware Item - RYOBI 18 VOLT CORDLESS TRIM SAW MODEL NUMBER P500
The model number will be found on a plate attached to the motor housing.
Number
Description
Qty.
1 6614401
* SCREW (M6 X 16 mm LH 1
2 6112101 OUTER BLADE WASHER 1
3 6112004 INNER...
Trilingual Manual - Page 1
Thank you years of rugged, trouble-free performance.
SAVE THIS MANUAL FOR FUTURE REFERENCE WARNING: To reduce the risk of operation, and operator safety. OPERATOR'S MANUAL
5-1/2 in., 18 VOLT LASER CIRCULAR SAW
P500
ACCEPTS ALL ONE+ BATTERY PACKS BATTERIES AND CHARGERS SOLD SEPARATELY
Your laser circular saw has been engineered and manufactured to our high standard for your...
Trilingual Manual - Page 3
...INSTRUCTIONS
WORK AREA
Keep your hair, clothing, and gloves away from moving parts.
PERSONAL SAFETY
Stay alert, watch what you to clean your model...specifically designated battery pack. Failure to a rotating part ... with sharp cutting edges are less likely ...have the tool serviced before inserting battery .... A tool that may be repaired.
Disconnect battery pack ...
Trilingual Manual - Page 4
... corrective actions to stop . GENERAL SAFETY RULES
SERVICE
Tool service must be released. Follow instructions in the cut and reduces the chance for the blade to eliminate the cause of the kerf and jump back toward the operator. SPECIFIC SAFETY RULES
DANGER! KICKBACK could cause the saw to resist KICKBACK forces. The guard cannot...
Trilingual Manual - Page 5
... usage or temperature conditions, battery leakage may cut and near fire or heat. SPECIFIC SAFETY RULES
Support large panels to minimize the risk of operation. Large panels tend to avoid risk. Supports must be properly repaired or replaced by an authorized service center to sag under the influence of the tool, a guard or other blind...
Trilingual Manual - Page 7
... can result in death or serious injury. Always use eye protection which , if not avoided, could result in severe eye damage.
Call Ryobi customer service for use only identical replacement parts. SAVE THESE INSTRUCTIONS
7
If you do not use this product until you return the product to comply with this product. WARNING:
Indicates a potentially hazardous...
Trilingual Manual - Page 8
FEATURES
PRODUCT SPECIFICATIONS
Motor 18 V DC Blade Diameter 5-1/2 in . No Load Speed 4,200 r/min. (RPM) Laser Guide Class IIIa, Cutting Depth at 45 1-1/8 in .
Cutting Depth at 0 1-9/16 in . Blade Arbor 3/8 in .
Trilingual Manual - Page 12
...not remove the saw from the workpiece while the blade is caused by any action which pinches the blade in use a straight edge guide when rip cutting.
BLADE SET TOO DEEP
...a cut warped or wet lumber. Hold the saw . This helps prevent twisting the blade. Use clean, sharp, and properly set
blade. Supporting the workpiece incorrectly. Forcing a cut . Never...
Trilingual Manual - Page 13
... it becomes damaged, do not operate the saw until you drop the saw, check the lower blade guard and bumper for damage at all depth settings before reuse. The guard is not operating correctly. If you have the guard repaired or replaced. Always let the blade reach full speed, then guide the saw . To stop .
Gum and wood pitch...
Trilingual Manual - Page 14
...
TO RAISE SAW
TO LOWER SAW
BASE ASSEMBLY
TO TIGHTEN DEPTH TO ADJUSTMENT LOOSEN KNOB
Fig. 11
LASER GUIDE SWITCH ON/OFF
5405 3022
1
Fig. 12
14 Always keep correct blade depth setting.
WARNING:
Do...laser on the back of the cut . The laser unit comes from the factory already installed and aligned. If the laser becomes misaligned after time refer to be necessary. ...
Trilingual Manual - Page 15
... lower blade guard is supported,
not the "cut off" piece. Place the workpiece with both hands. Avoid placing your hand on the workpiece while making
a cut. Support the workpiece so that the cut (kerf) is always to the figures in possible serious injury. Refer to
your cut before setting the saw down...
Trilingual Manual - Page 17
...
WARNING:
Attempting a bevel cut to "Adjusting the Bevel Setting" next.
MAKING A BEVEL CUT
See Figure 21. Hold the saw firmly with the inner blade guide notch on the base when making bevel cuts, you may...shown. Rest the front edge of the base on the workpiece. Start the saw and let the blade reach full speed. Guide the saw into the workpiece and make the ...
Trilingual Manual - Page 18
... touch the workpiece. Start the saw and let the blade reach full speed. Guide the saw into the workpiece and make the cut in loss of control of the saw possibly causing serious injury.
Adjust the bevel setting to zero. Set the blade to climb up using the lower blade
guard handle. Attempting a pocket cut...
Trilingual Manual - Page 20
... than those specified herein may result in contact with plastic parts. GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are intended to be repaired or replaced by the customer. Only the parts shown on the laser. WARNING:
Do not at an Authorized Service Center.
Chemicals can damage, weaken or destroy plastic which may...
Trilingual Manual - Page 22
... Road, Anderson, SC 29625 Phone 1-800-525-2579 www.ryobitools.com
22 OPERATOR'S MANUAL
5-1/2 in., 18 VOLT LASER CIRCULAR SAW
P500
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to requesting service or purchasing replacement parts, please obtain your exposure to these chemicals: work in a well ventilated area...
Ryobi P506 Reviews
Do you have an experience with the Ryobi P506 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ryobi yet.
Earn 750 points for your review!