Ryobi P213 Support and Manuals
Get Help and Manuals for this Ryobi item
Most Recent Ryobi P213 Questions
Is P213 The One I Want For My Dp102l Drill Press
ok im looking for a manual for my DP102L RYOBI 10 inch drill press, and I want to know if the P213 w...
ok im looking for a manual for my DP102L RYOBI 10 inch drill press, and I want to know if the P213 w...
(Posted by martinb4 8 years ago)
Popular Ryobi P213 Manual Pages
English Manual - Page 2
......18-20 Adjustments...21-22 Maintenance...23 Troubleshooting...24 Parts Ordering / Service...Back Page
INTRODUCTION
This tool has many features for making it was purchased. You can obtain the location of the Service Center nearest you . Batteries are warranted for example, a bill of its use more pleasant and enjoyable...
English Manual - Page 7
... only by a qualified service technician. Always use only identical replacement parts. Indicates a potentially hazardous situation, which can result in death or serious injury. When servicing, use eye protection which , if not avoided, will result in property damage. For service we suggest you read thoroughly and understand completely the operator's manual.
SYMBOL SIGNAL DANGER: WARNING...
English Manual - Page 9
... a block so the end (or part of the end) is angled rather... (drill presses) A small hole drilled in...supported. GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed...set) outward from being placed inadvertently in a workpiece that area which will be used in a non-through cut by guiding it applies to the workpiece, that serves as a guide...
English Manual - Page 23
... replacement parts. GENERAL MAINTENANCE
Avoid using the laser for an extended time.
23 Apply a light coat of automotivetype paste wax to the table and column to help keep the vertical movement smooth and to avoid deterioration. Remove the batteries if you feel an unusually high level of the drill press.
MAINTENANCE
WARNING:
When servicing...
English Manual - Page 24
... tension. troubleshooting
Problem
Noisy operation Bit burns or smokes
Excessive drill runout or wobble Drill bit binds in chuck Chuck not properly installed Worn spindle bearings
Replace bit. allow drill to clear chips. Sharpen or replace bit. Lubricate bit for metal work. Install chuck properly. Bent bit Bit not properly installed in workpiece Workpiece support loosens
Possible...
English Manual - Page 26
... at www.ryobitools.com for repair parts or service, simply contact your nearest Authorized Service Center. AND SERIAL NO. Please record the model number and serial number in . OPERATOR'S MANUAL
10 in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
• MODEL NUMBER
DP102L
• SERIAL NUMBER
Ryobi® is...
User Manual 4 - Page 2
For the service center nearest you call 1-800-525-2579.
2 DRILL PRESS - To avoid the possibility of the double insulated system. MODEL NUMBER DP102L
60 59
99
98
61
97
66...23
22
4
13
19
14
3
18
2 1
NOTE: The assembly shown represents an important part of alteration or damage to the system, service should be performed by your nearest Ryobi Authorized Service Center. RYOBI 10 in.
User Manual 4 - Page 3
RYOBI 10 in all correspondence regarding your DRILL PRESS or when ordering repair parts. KEY
NO.
1 2 ...Set Screw 1 089140200047 Baffle 1 TDP03002 Screw (M8 X 8 mm Hex Hd 1 089140200049 Head Stock 1 089140200050 Battery Box 1 TDP06002 Hex Nut (M10 2 13104008 Spring Cap 1 13104009 Torsion Spring 1 13104007 Spring Retainer 1
3 DRILL PRESS - MODEL NUMBER DP102L
The model...
User Manual 4 - Page 4
...model number in . RYOBI 10 in all correspondence regarding your DRILL PRESS or when ordering repair parts. MODEL NUMBER DP102L
The model number will be found on a label attached to the motor housing.
PARTS LIST FOR FIGURE A
KEY
PART...1
983000641 Operator's Manual
4-26-12
(REV:09)
4 NUMBER
DESCRIPTION
QTY.
55
13202014 Cord Clamp 4
56
089140200056 Battery Box Cap 1
...
User Manual 5 - Page 1
... in. (254 mm) DRILL PRESS MODEL DP101
THANK YOU FOR BUYING A RYOBI BENCH TOP DRILL PRESS. Your new Drill Press has been engineered and manufactured to Ryobi's high standards for Safe Operation, Warnings, and Cautions. CAUTION: Carefully read through this entire operator's manual before using your machine properly and only for buying Ryobi tools. Pay close attention to...
User Manual 5 - Page 3
... identical Ryobi replacement parts.
DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS
WARNING:
Do not attempt to operate this tool.
3 IMPORTANT
Servicing requires extreme care and knowledge and should be used in accidents involving fire, electric shock, or serious personal injury. WARNING:
Observe all instructions, safety rules, etc. Save this operator's manual and review frequently...
User Manual 5 - Page 5
..., assembly, or set-up , adjusting, or changing accessories.
3. Refer to filter out microscopic particles. Use only Ryobi identical replacement parts.
32. Some examples of work with respect to cause cancer, birth defects or other users. To reduce your exposure to these chemicals: work in a well ventilated area, and work . SPECIFIC SAFETY RULES FOR DRILL PRESSES
1. Always...
User Manual 5 - Page 15
..., allow drill to clear chips. See page 14. TROUBLE SHOOTING
Problem
Noisy operation. Dry spindle. Loose spindle pulley or motor pulley. See page 14. Tighten set screws in workpiece
Excessive feed pressure. See page 14.
Incorrect speed. Chips not coming out of hole.
Change speed. Sharpen or replace bit.
Bent bit. Bit not properly installed in...
User Manual 5 - Page 16
...12 gauge - 20 amp circuit.
• SERVICE
Now that you call 1-800-525-2579 for repair parts or service, simply contact your nearest Ryobi Authorized Service Center.
Please record the serial number in ...to the head assembly. The model and serial numbers of power. When working area.
OPERATOR'S MANUAL 10 in. (254 mm) Drill Press Model DP101
EXTENSION CORD CAUTION
When using...
User Manual 8 - Page 3
...13201014D TABLE 1 10 13201004 TABLE SUPPORT W/SCALE......... 1 11 16101013A TABLE LOCK HANDLE 1 12 13201006 GEAR 1 13 13201008 WORM GEAR 1 14 13201011C COLUMN COLLAR 1 15 TDP03001 SET SCREW (M8 X 10 mm...MANUAL 972000909R REPAIR SHEET (REV:01) 06-28-06
* Standard Hardware Item - RYOBI 10 in all correspondence regarding your DRILL PRESS or when ordering repair parts. Always mention the model...
Ryobi P213 Reviews
We have not received any reviews for Ryobi yet.