Ridgid R3202 Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid R3202 manuals!
Problems with Ridgid R3202?
Ask a Question
Free Ridgid R3202 manuals!
Problems with Ridgid R3202?
Ask a Question
Popular Ridgid R3202 Manual Pages
Owners Manual - Page 1
...must read and understand the operator's manual before using this product. When properly cared for, it will give you for dependability, ease of operation, and operator safety. WARNING:
To reduce the risk of rugged, trouble-free performance. CIRCULAR SAW
DOUBLE INSULATED R3202
Your circular saw has been engineered and manufactured to our high standards for buying a RIDGID® product.
Owners Manual - Page 2
... Power Tool Safety Warnings and Instructions 3-4 Circular Saw Safety Warnings and Instructions...4-5 Symbols...6-7 Electrical...8 Features...9-10 Assembly...10-11 Operation...12-17 Adjustments...18 Maintenance...19 Accessories...19 Warranty...21 Customer Service Information...Back page
INTRODUCTION...
Owners Manual - Page 4
... not operate saw blade is pinched or bound tightly by a qualified repair
person using only identical replacement parts. Never clamp or tie the lower guard into existing walls or other part, in all angles and depths of cut and near the line of the kerf and jump back toward the operator. GENERAL POWER TOOL SAFETY WARNINGS AND INSTRUCTIONS
SERVICE...
Owners Manual - Page 5
... be serviced before placing saw to filter out microscopic particles.
The smaller the gauge number, the heavier the cord. Loose clothes, jewellery, or long hair can be properly repaired or replaced by an authorized service center. Raise lower guard by insulated gripping surfaces when performing an operation where the cutting tool may operate sluggishly due to damaged parts...
Owners Manual - Page 7
...over eyeglasses or standard safety glasses with this product.
WARNING:
The operation of risk associated with side shields. SAVE THESE INSTRUCTIONS
For service we suggest you read thoroughly and understand completely the operator's manual. Always use only identical replacement parts. SERVICE
Servicing requires extreme care and knowledge and should be performed only by a qualified...
Owners Manual - Page 10
...operator, a dust chute is too thick to allow motor to come in contact with the blade guides, while thicker blades will prevent blade screw from securing blade on saw...PLUG
This saw dust and chips away from
the box.
Circular Saw Blade 6 mm Blade Wrench Operator's Manual
WARNING:
If any parts are replaced.
Ergonomic Design
The design provides comfort when operating in serious...
Owners Manual - Page 12
... board) Cross cutting/Rip cutting Bevel cutting Pocket cutting NOTE: The use a straight edge guide when rip cutting.
This helps prevent twisting the blade.
Use clean, sharp, and properly set blade.
Supporting the workpiece incorrectly.
Forcing a cut .
12 Fig. 6
To lessen the chance of a second is driven...
Owners Manual - Page 13
... instantly returns to the closed position several times. OPERATION
Use steady, even pressure when making a cut efficiently if they are always available. Remove saw blade from the saw , check the lower blade guard and bumper for repair.
13
If you have the guard repaired or replaced. Normally this will restore the guard to remove these...
Owners Manual - Page 14
...11.
Always let the blade reach full speed, then guide the saw and to release.
Determine the desired depth...setting.
The levers on the saw to "kickback" towards you release the switch trigger, allow the blade to come to lock into position.
Do not remove the saw : Depress the switch trigger. OPERATION
STARTING/STOPPING THE SAW
See Figure 9. To start the saw from the saw...
Owners Manual - Page 15
... always to
your side. Support the workpiece near the cut. Clamp the workpiece securely so that is closed before setting the saw and reposition the cord to prevent it from hanging up again. Always place
the cord to learn the correct and incorrect ways for operating the saw with the "good" side down...
Owners Manual - Page 16
... with the saw. OPERATION
RIP CUTting
See Figures 15 - 16. Use caution to prevent the blade from binding in the cut to Adjusting Bevel Setting later in ...Saw along a guideline to 56°. To rip cut in while raising the motor housing to set the bevel setting above 45° and up to determine how much you reach the desired angle setting on the guide is securely locked in this manual...
Owners Manual - Page 17
...saw possibly causing serious injury.
Adjust the bevel setting to zero. Set the blade to the correct blade depth setting. Swing the lower blade guard up on the workpiece. Start the saw and let the blade reach full speed. Guide the saw... Hold the saw firmly with a hand saw or sabre saw from the workpiece. OPERATION
WARNING:
Attempting a bevel...
Owners Manual - Page 19
... operation is required. Electric tools used on these accessories, call 1-866-539-1710. Edge Guide...690119003
WARNING:
Current attachments and accessories available for the life of the power supply cord is extremely important to bearings, brushes, commutators, etc.
Do not use any of high grade lubricant for use only identical RIDGID® replacement parts...
Owners Manual - Page 21
... implied warranties, including warranties of merchantability or fitness for RIDGID® branded hand held and stationary power tools. This warranty gives you specific legal rights, and you . This product is licensed from misuse, abuse, neglect, alteration, modification or repair by other than an authorized service center for a particular purpose, that cannot be disclaimed under...
Owners Manual - Page 22
... repair parts, always give the following information:
Model No. Please record the serial number in .
Be sure to the motor housing. The model number of the authorized service center nearest you call 1-866-539-1710 or visit us online at www.ridgid.com. R3202
Serial No.
987000-316 5-27-08 (REV: 01) OPERATOR'S MANUAL
7-1/4 in the space provided below. CIRCULAR SAW...
Ridgid R3202 Reviews
We have not received any reviews for Ridgid yet.