Ridgid RP 330-C Support and Manuals
Get Help and Manuals for this Ridgid item
This item is in your list!
View All Support Options Below
Free Ridgid RP 330-C manuals!
Problems with Ridgid RP 330-C?
Ask a Question
Free Ridgid RP 330-C manuals!
Problems with Ridgid RP 330-C?
Ask a Question
Most Recent Ridgid RP 330-C Questions
Popular Ridgid RP 330-C Manual Pages
Owners Manual - Page 1
pág. 27 Read this Operator's Manual carefully before using this manual may result in electrical shock, fire and/or serious personal injury.
• Français - 13 • Castellano -
Failure to understand and follow the contents of this tool. RP 330 Manual
Pressing Tool
WARNING!
Owners Manual - Page 2
... Jaw Set ...7 Pressing A Fitting With Typical Actuator and Press Ring Set 8 Inspecting The Pressed Connection ...9 Maintenance Instructions Cleaning and Lubrication ...10 Required Maintenance at RIDGID Authorized Service Center 10 Accessories ...10 Storage ...10 Service and Repair ...10 Troubleshooting ...11 RP 330 Diagnostic Codes ...12 Lifetime Warranty ...Back Cover
ii
Ridge Tool Company
Owners Manual - Page 3
Serial No. RP 330
Pressing Tool
RP 330-B Battery Tool
RP 330-C Corded Tool
RP 330 Pressing Tool
Record Serial Number below and retain product serial number which is located on nameplate.
Owners Manual - Page 4
...Not every precaution applies to every tool, and some do not apply to your mains-operated (corded) power tool or battery-operated (cordless) power tool. This is the electrical shock symbol... tool. RP 330 Pressing Tool
Safety Symbols
In this operator's manual and on the safe and proper operation of the equipment. NOTICE NOTICE indicates information that follow the warnings and instructions ...
Owners Manual - Page 5
... bind and are easier to be caught in accordance with the charger specified by poorly maintained power tools.
• Keep cutting tools sharp and clean. RP 330 Pressing Tool
Personal Safety
• Stay alert, watch what you are tired or under the influence of drugs, alcohol, or medication. Carrying power tools with specifically designated battery packs. Properly maintained cutting...
Owners Manual - Page 6
...Never attempt to batteries.
Replace with the machine for RP 330-B only)
WARNING Read the battery charger manual before using the RP 330 Pressing Tool to deform a fitting, it has been dropped or damaged in locations where temperatures will prevent serious damage to repair a damaged jaw set instructions, the fitting manufacturer's installation instructions and the instructions for other...
Owners Manual - Page 7
... damage. Clean any problems are found , do not use machine until the cord or battery has been properly repaired or replaced.
2. If any oil, grease or dirt from electric shock, crushing injures, attachment failure and other condition which may prevent safe and normal operation. RP 330 Pressing Tool and Standard Series Jaw Set
Specifications
RP 330-C Corded Pressing Tool: Motor
Voltage...
Owners Manual - Page 8
... of the pressing tool warning label. RP 330 Pressing Tool
4. With your hands and fingers away from electric shock, fire, crushing injuries and other conditions exist,
use the Diagnostic Codes information on page 12 to be done and determine the correct RIDGID tool and attachment(s) for the location of the switch to the tool and if required, the battery. Check work...
Owners Manual - Page 9
..., with dry hands insert the battery into the base of press tool attachments. Keep your eyes against dirt and other damage. Connect RP 330 to press.
Make sure the contour of the jaw set and tool from the tool
attachment during the press cycle. rated for the pressing tool attachment being used and the fitting manufacturers specific installation instructions. Make sure that the work...
Owners Manual - Page 10
... specified in jaw set and between jaw set and tool are fully engaged in the press ring (Figure 10). RP 330 Pressing Tool
Figure 6 - The press cycle takes about five (5) seconds. This assures consistent, repeatable press joint integrity. Press jaw arms to a RIDGID Authorized Service Center for ten (10) minutes. Connect RP 330 to fitting system's operator's manual. To restart tool, it is...
Owners Manual - Page 11
.... Inspect the pressed fitting. Maintenance Instructions
WARNING Make sure cord is unplugged or battery is complete, squeeze actuator arms to open and separate actuator from tool before performing maintenance or making any of these problems are still aligned with the end of the control ring and label indicates to successfully complete a pressed connection. RP 330 Pressing Tool
point injuries...
Owners Manual - Page 12
... 18V Lithium-Ion Battery Pack 2.2Ah 115V Charger Carrying Case (Plastic)
Storage
Place the tool and jaws in the hands of RIDGID attachments available for use with each use attachments that are installing.
WARNING Store the carrying case in attachments with the RP 330, such as those listed below. For any questions regarding the service or repair of children and...
Owners Manual - Page 13
... not aligned with the fitting contour. Inspect and repress fitting. Jaw contour was not successfully completed.
RP 330 Pressing Tool
Troubleshooting
SYMPTOM
POSSIBLE REASONS
SOLUTION
Tool will not function until tool is serviced.
Red LED glows. Inspect the cord and replace if necessary. Failure to the fully closed . Insert accessory mounting pin to do so may result in the...
Owners Manual - Page 14
RP 330 Pressing Tool
RP 330 Diagnostic Codes
LED
Green
Status
Glows Blinks
Red Yellow
Blinks Glows
Blinks Glows
Description
Tool ON. Corded Tools: Connect tool to 100'. Out of acceptable voltage range - Service after 32,000 cycles or after 32,000 cycles.
NOTE: Tool will lock after a malfunction.
12
Ridge Tool Company If using extension cord,
use 16 AWG for 50' or less...
Ridgid RP 330-C Reviews
Do you have an experience with the Ridgid RP 330-C that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ridgid yet.
Earn 750 points for your review!