Panasonic EYFLA4A Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic EYFLA4A manuals!
Problems with Panasonic EYFLA4A?
Ask a Question
Free Panasonic EYFLA4A manuals!
Problems with Panasonic EYFLA4A?
Ask a Question
Popular Panasonic EYFLA4A Manual Pages
EYFLA4A User Guide - Page 4
...Loose clothes, jewellery or long hair can be repaired.
3) Disconnect the plug from the power source and/or the battery pack from moving parts.
Use the correct power tool for the ...battery operated (cordless) power tool. A wrench or a key left attached to follow all instructions listed below refers to your body is an increased risk of inattention while operating power tools may ignite...
EYFLA4A User Guide - Page 5
... the work to tighten bolts, nuts, and screws. II. Read "the Safety Instructions" booklet and the following before using only identical replacement parts. III.ADDITIONAL SAFETY
RULES
1) Wear ear protectors when using the tool for one terminal to deliver consistent tightening torque. Such preventive safety measures reduce the risk of starting the power tool...
EYFLA4A User Guide - Page 6
...
holes on the socket and tool.) 3 Attach the rubber ring by holding the speed control trigger halfway (speed control mode) so that the motor stops. EYFLA4A/EYFLA4AR/EYFLA5A/EYFLA5AR
12 mm (15/32")
9 mm - 9.5 mm 6.35 mm (23/64" - 3/8") (1/4")
NOTE: Be sure to attach the rubber ring to make sure it into...
EYFLA4A User Guide - Page 7
...so that it may not function well with one side only You may be subjected to the driver. Do not use . Attaching or Removing Bat tery Pack
1.
To connect the battery... the socket and pin-detent do not interfere with the driver due to
the square drive. Alignment marks
- - CAUTION: • When attaching a socket to the driver,
verify that the pin-detent makes contact with a pin...
EYFLA4A User Guide - Page 9
... of procedures other than those specified herein may result in LED light is set the lever to check whether the torque control function was activated.
Lamp display Green (For approx. 2 seconds) Red... toggles the LED light on under the following conditions: • When the torque clutch is designed to another pack. Use of controls or adjustments or performance of rotation before...
EYFLA4A User Guide - Page 11
... being performed. Press the and buttons to select the clutch setting that the torque control function is not operated for the work being tightened: Material, seating surface finish
Setting the tool to configuration mode
1. Configuring the torque clutch setting (1)
(2)
NOTE: • Tools ship from the factory set to configuration mode.
Engage the switch while pushing the...
EYFLA4A User Guide - Page 12
... level. • The tool's panel will stop flashing and light up continuously. Press the and buttons to set the snug point detection level to guide your selection of torque clutch setting. (See the following tightening torque chart) 2.
• You can set the snug point detection level and retightening prevention time at snug point detection level "L1...
EYFLA4A User Guide - Page 13
... mode. (See page 11.)
2. Press the OK button to accept the selected setting. • The control panel will stop flashing and light up, and the torque clutch setting will begin flashing.
Set the tool to set the desired time. Press the interval set operates to verify the new value after it automatically...
EYFLA4A User Guide - Page 14
... describes how to register the tool and assembly qualifier, see the assembly qualifier instruction manual. Press the torque set button.
• Control panel display Display: The torque set lights up. Checking the interval 1. Press the interval set button.
• Control panel display Display: The interval set lights up . Press the format button again. • Radio signal range limitation...
EYFLA4A User Guide - Page 15
...torque set display lights up. The contacts that the Assembly Qualifier's group setting has been configured correctly.
• Improve the reception state, for example by moving the Assembly Qualifier closer to cool before having them serviced... chart before resuming use of drive component parts (hammer, etc.) used to the torque clutch setting display. Error Display
In the event of a tool ...
EYFLA4A User Guide - Page 16
...found on how to recycle this battery.
[Battery Charger]
Charging
Read the operating manual for Panasonic battery charger for an hour in a location where the temperature is recyclable powers .... during operation.
• When battery pack is removed from the main body of the tool, replace the battery pack cover immediately in order to 40°C (104°F).
MAINTENANCE
Use only a dry...
EYFLA4A User Guide - Page 17
... with Part 15 of the FCC Rules. These limits are designed to operate this device must accept any interference received, including interference that may not cause harmful interference and (ii.) this equipment. Operation is no guarantee that to which can radiate radio frequency energy and, if not installed and used in the instructions. Panasonic...
EYFLA4A User Guide - Page 18
...SPECIFICATIONS
MAIN UNIT
Model
...Motor Chuck size
EYFLA4
A
AR
Single- 9 - 9.5 mm ended (23/64" - 3/8")
EYFLA5
A AR Q QR
10.8 V DC
9 - 9.5 mm □9.5 mm
(23/64"
(3/8")
- 3/8")
EYFLA6
EYFMA1
P,J PR,JR
P,J
14.4 V DC
□12.7 mm (1/2")
□12.7 mm (1/2")
Double- 12 mm (15/32") ended
12 mm (15/32")
No load Stage speed
Impact per minute
Stage
Maximum torque
Torque...
EYFLA4A User Guide - Page 19
...(13/32") Approximately 29 g (0.6 lbs)
Assembly Qualifier (not included with shipment)
Model Rating Dimensions
Weight
EYFRZ01
EYFR02
See the rating plate on the bottom of the Assembly Qualifier...
Model Indoor/Urban Range Outdoor RF line-of-sight range Transmit Power Assembly Qualifier Sensitivity FCC Part 15.249 Industry Canada
EYFLA 100ft./30m 300ft./100m 1mW(0dBm) -92dBm(1% packet error)...
EYFLA4A User Guide - Page 56
PANASONIC CONSUMER ELECTRONICS COMPANY
One Panasonic Way, Secaucus, New Jersey 07094
EN, FR, ES EY9810FLA43 2011 08
Printed in Japan
Panasonic EYFLA4A Reviews
We have not received any reviews for Panasonic yet.