Panasonic AWRL400 - ROLL UNIT Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic AWRL400 manuals!
Problems with Panasonic AWRL400?
Ask a Question
Free Panasonic AWRL400 manuals!
Problems with Panasonic AWRL400?
Ask a Question
Popular Panasonic AWRL400 Manual Pages
AWRL400 User Guide - Page 2
...digital apparatus complies with Part 15 of the unit.
1 indicates safety information.
2 WARNING:
TO PREVENT INJURY, THIS APPARATUS MUST BE SECURELY ATTACHED TO THE FLOOR/WALL IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS...to comply with the instruction manual, may be of sufficient magnitude to constitute a risk of important operating and maintenance (service) instructions in which case the...
AWRL400 User Guide - Page 4
...6 Accessories 6 Precautions for use 6 Installation precautions 7 Parts and their function 8 Installation 12
$ Assembling the pan/tilt head 12 $ Setting the mounting direction switch 14 $ Setting the PCB switches 15 $ Installing the pan/tilt head 16 $ Mounting the camera 17 $ Attaching the wire 18 Replacing the consumable parts 19 Specifications 20
AW-RC400 Cable Compensation Unit 38...
AWRL400 User Guide - Page 6
... option.
≥ The shooting positions and settings for use
The AW-PH400 uses a manganese dioxide-lithium battery (CR2032).
Indoor Pan/Tilt Head AW-PH400
Introduction
≥ The stand-alone indoor pan/tilt head can be rotated through 300 degrees in the vertical direction and 400 degrees in "Replacing the consumable parts" (page 19).
AWRL400 User Guide - Page 7
...not install the unit on any of its sides.
≥ Avoid using the unit in the kitchen and other locations with lots of steam and oily vapors.
≥ Mount the camera on it and its rotating part. Doing...the mounting screws separately since they are not supplied with anything when the pan/tilt head swivels, and set off-balance by the unit is 17.6 lbs (8 kg). It cannot be used if the unit ...
AWRL400 User Guide - Page 9
... turned on this base.
: Pan/tilt head mounting holes These four holes are used when installing the pan/tilt head.
; Bottom panel
< PROMPTER connector The prompter is connected to the ... washers (4 of each provided as accessories) These parts are used to secure the camera mounting base to the rotary arm.
6 Tally lamp (accessory) This is set to about one-third.
87654321 ?>= when it ...
AWRL400 User Guide - Page 10
...installed in the convertible camera.
When it has been mounted.
? C LENS I/F (1) connector [LENS I CABLE COMP OFF/ON switch [CABLE COMP] When this is set to secure the camera firmly after it is set... set to the SDI OUT connector on the functions of the optional card, a special camera cable (sold separately) is required. Indoor Pan/Tilt Head AW-PH400
Parts and their function
= Guide pin...
AWRL400 User Guide - Page 15
... sure to ask your dealer to install the unit.)
$ Setting the PCB switches
The switches on the CONNECTOR PCB will need to be set in accordance with the signals to be transmitted and the equipment to be connected to the pan/tilt head. (The switches are set to support analog/SDI at the factory.)
≥...
AWRL400 User Guide - Page 16
... head (pan/tilt head, camera and lens cable). ≥ Install the pan/tilt head in malfunctioning.
16 Do not install the pan/tilt head on its side since its prescribed operation and performance cannot be absolutely sure to install the unit.)
$ Installing the pan/tilt head
When installing the pan/tilt head, follow the instructions below carefully.
AWRL400 User Guide - Page 20
...20 Specifications are approximate. Genlock input:
BNC Black burst or composite video signal
Prompter input (PROMPTER IN):
BNC Through output to PROMPTER connector
Prompter output (PROMPTER OUT):
D-SUB 15-pin
Camera .... The tilt range is limited to 190 degrees by the initial setting of camera to change the AW-RP400 setting.
Pan range: 400 degrees (approx. ±200 degrees) Maximum...
AWRL400 User Guide - Page 22
... the convertible cameras mounted on the pan/tilt heads can be controlled at the same time.
≥ By installing an additional ...be set. ≥ The connection distance between the control panel and
pan/tilt head system can be discarded at the end of its service life... be set Rack-mounting adaptors 2 Mounting screws (M4!8 mm 4
22 NOTE
≥ The AW-RP400 cannot be used to control the model AW-...
AWRL400 User Guide - Page 23
... on the additional unit to [S] (slave). Parts and their function
$ Front panel A B C D
Pan/Tilt Control Panel AW-RP400 E F GH I 1
2 3
4
J
5
6
K
7 8
9
:
L
AW-RP400
1 EXT CONT [M/S] switch This switch is installed and used, it is set to [OFF], the power supply from the connected pan/tilt heads to the cameras is pressed, the buzzer of the connected...
AWRL400 User Guide - Page 24
...display (NEAR > FAR).
? Pan/Tilt Control Panel AW-RP400
Parts and their function
7 IRIS [AUTO/MANU/LOCK] button Use this... pan/tilt head system. The pan/tilt head and camera setting can be allocated to OPTION switches A to H by... panel. When the pan/tilt head is rotated to which the lever is adjusted manually using the IRIS control on the top of the lever.
;
OPTION switches [A ...
AWRL400 User Guide - Page 32
... operation panel has been connected to the AW-RP400 control panel. are connected, INTERLOCK is always set regardless of the SD memory card to this unit only, and refrain from using it with a personal computer, digital camera or other unit as well. The process is completed when the EXECUTE display is cleared from...
AWRL400 User Guide - Page 38
...).
≥ It features a 5µs advance function for the sync signals in order to provide easy support for a system (another cable compensation unit is required) in order to protect the environment. In the ... cable connected between this AW-RC400 cable compensation unit and the camera is to be discarded at the end of its service life, ask a specialized contractor to dispose of it does not...
AWRL400 User Guide - Page 59
...least 500 mm or so
Connector: HR10A-10J-12P made by Hirose Electric
Connect to the ZOOM/FOCUS connector on the camera.
Cable length: At least 800 mm or so
Connect to the IRIS connector on lens. Connector: HR10A-10J-12P...: HR25-9P-20P made by Hirose Electric
Connect to the lens cable. Cable specifications
59
When an IASD, WASD or VASD lens (digital drive) made by Canon is used .
Panasonic AWRL400 Reviews
We have not received any reviews for Panasonic yet.