Owner Manual
Page 4
... To prevent this unit should turn off your plug, proceed as such are likely to the terminal which is within the specified rating, excessive current may flow in compliance with the corresponding technical standards such as near a turntable, CD player or DVD player, howling... to BS1362 and have no batteries are free from audio test CDs and so on . 4. MIYAGI ONKYO EUROPE ELECTRONICS GmbH Memory Backup The AV receiver uses a battery-less memory backup system in which neutralizes the magnetic field, thereby removing any of the following signals are coloured in ...
... To prevent this unit should turn off your plug, proceed as such are likely to the terminal which is within the specified rating, excessive current may flow in compliance with the corresponding technical standards such as near a turntable, CD player or DVD player, howling... to BS1362 and have no batteries are free from audio test CDs and so on . 4. MIYAGI ONKYO EUROPE ELECTRONICS GmbH Memory Backup The AV receiver uses a battery-less memory backup system in which neutralizes the magnetic field, thereby removing any of the following signals are coloured in ...
Owner Manual
Page 56
... • When the subwoofer volume level is set the Input Display to MD, CDR, or HDD (see page 35). • To control an Onkyo component that's connected via , point the remote controller at the AV receiver. 56 ler mode (page 12). • If you've connected an -capable... control code. There's no picture? • Make sure that each video component is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn't recognize it . • An audio cable may cause noise. • Passing cars and airplanes ...
... • When the subwoofer volume level is set the Input Display to MD, CDR, or HDD (see page 35). • To control an Onkyo component that's connected via , point the remote controller at the AV receiver. 56 ler mode (page 12). • If you've connected an -capable... control code. There's no picture? • Make sure that each video component is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn't recognize it . • An audio cable may cause noise. • Passing cars and airplanes ...
Owner Manual
Page 58
...Audio Outputs Analog Outputs TAPE,VIDEO1 Speaker Outputs SP-A (FL, FR, C, SL, SR, SW) + SP-B (L, R) Phones 1 Specifications Amplifier Section Rated Output Power North American (FTC): (FL, FR, C, SL, SR) 95 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1 kHz, with... Signal to Noise Ratio Speaker Impedance 180 W + 180 W (3Ω, Front) 140 W + 140 W (4Ω, Front) 95 W + 95 W (8Ω, Front) 0.9% (Power Rated) 60 (Front, 1kHz, 8Ω) 200 mV/ 47 kΩ (LINE) 200 mV/ 470 Ω (REC OUT) 10 Hz-50 kHz/ +1 dB-3 dB (Direct mode) ...
...Audio Outputs Analog Outputs TAPE,VIDEO1 Speaker Outputs SP-A (FL, FR, C, SL, SR, SW) + SP-B (L, R) Phones 1 Specifications Amplifier Section Rated Output Power North American (FTC): (FL, FR, C, SL, SR) 95 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1 kHz, with... Signal to Noise Ratio Speaker Impedance 180 W + 180 W (3Ω, Front) 140 W + 140 W (4Ω, Front) 95 W + 95 W (8Ω, Front) 0.9% (Power Rated) 60 (Front, 1kHz, 8Ω) 200 mV/ 47 kΩ (LINE) 200 mV/ 470 Ω (REC OUT) 10 Hz-50 kHz/ +1 dB-3 dB (Direct mode) ...