English Manual
Page 2
If a decal is a registered trademark of ICON IP, Inc. 2 NORDICTRACK is missing or illegible, see the front cover of the warning decal(s). TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 6 PART IDENTIFICATION CHART 7 ASSEMBLY 8 HOW TO USE THE ELLIPTICAL 18 FCC INFORMATION 26 MAINTENANCE AND TROUBLESHOOTING 27 EXERCISE GUIDELINES 29 PART...
If a decal is a registered trademark of ICON IP, Inc. 2 NORDICTRACK is missing or illegible, see the front cover of the warning decal(s). TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 6 PART IDENTIFICATION CHART 7 ASSEMBLY 8 HOW TO USE THE ELLIPTICAL 18 FCC INFORMATION 26 MAINTENANCE AND TROUBLESHOOTING 27 EXERCISE GUIDELINES 29 PART...
English Manual
Page 7
The number in the hardware kit, check to identify the small parts needed for assembly. Extra parts may be included. M5 Washer (32)-2 M8 Washer (97)-8 M10 Split Washer (105)-8 16mm Wave Washer (54)-2 M8 Locknut (... number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly.
The number in the hardware kit, check to identify the small parts needed for assembly. Extra parts may be included. M5 Washer (32)-2 M8 Washer (97)-8 M10 Split Washer (105)-8 16mm Wave Washer (54)-2 M8 Locknut (... number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly.
English Manual
Page 8
... two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." ...;• saves you time if you ever need to contact Customer Care • allows us to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you do not use power tools. 1. Go to www.nordictrackservice.com/ registration on your computer and...
... two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." ...;• saves you time if you ever need to contact Customer Care • allows us to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you do not use power tools. 1. Go to www.nordictrackservice.com/ registration on your computer and...
English Manual
Page 28
...the Idler Screw (89). Then, carefully remove the Right Roller Arm assembly from the Left and Right Shields (73, 74). Use a flat screwdriver to be adjusted. Remove the M4 x 19mm Screws (5) and the M4 x 48mm Screw (107) from the elliptical. 89 91 Reattach the right shield, the right roller arm, ...the right pedal arm, the shield cover cap, and the shield cover. 28 Then, remove the Right Shield. Next, see assembly step 16 on page 35. HOW TO ADJUST THE DRIVE...
...the Idler Screw (89). Then, carefully remove the Right Roller Arm assembly from the Left and Right Shields (73, 74). Use a flat screwdriver to be adjusted. Remove the M4 x 19mm Screws (5) and the M4 x 48mm Screw (107) from the elliptical. 89 91 Reattach the right shield, the right roller arm, ...the right pedal arm, the shield cover cap, and the shield cover. 28 Then, remove the Right Shield. Next, see assembly step 16 on page 35. HOW TO ADJUST THE DRIVE...