Netgear XSM7224S - ProSafe 10 Gigabit Stackable Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear XSM7224S manuals!
Problems with Netgear XSM7224S?
Ask a Question
Free Netgear XSM7224S manuals!
Problems with Netgear XSM7224S?
Ask a Question
Popular Netgear XSM7224S Manual Pages
APS300W Installation Guide - Page 1
..., follow these steps: 1. The XSM7224S Switch supports dual APS300W power supplies, so you can be replaced without stopping the switch or requiring a reboot. When another APS300W while replacing the failed power supply. APS300W_IG_2Nov10.fm Page 1 Friday, November 12, 2010 10:37 AM
Installation Guide
Replacing an APS300W Power Supply
ProSafe® Auxiliary Power Supply APS300W
The...
XMS7224S CLI Manual - Page 46
... 1518 - 9216 for the interface. Default Format Mode
1518 (untagged) mtu Interface Config
no mtu Interface Config
Switching Commands
3-5
v1.0, November 2010
Format Mode
description Interface Config
mtu
Use the mtu command to configure jumbo frame support for frames that Layer-2 headers might require. You can use the mtu command to set the maximum transmission unit (MTU...
XMS7224S CLI Manual - Page 59
... this command sets the external-path cost for this port within a specific multiple spanning tree instance or the common and internal spanning tree instance, depending on the parameter. Default
Format Mode... the path cost value is set the external cost as a number in the range of 0 to 200000000 or auto. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
no spanning...
XMS7224S CLI Manual - Page 60
... 2010
3-19 ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
no spanning-tree mst Interface Config
spanning-tree mst instance
This command adds a multiple spanning tree instance to the default value, i.e. If the you specify external-cost, this command sets the external path cost for this port within a range of multiple instances supported by the switch is...
XMS7224S CLI Manual - Page 223
... xxx xxx Firmware Rev: xxx xxx xxx
Switching Commands
v1.0, November 2010
3-182 Shows the remote port's PSE priority.
Example: The following shows example CLI display output for a given type of location information. Shows the remote port's PD power requirement. Shows the remote port's PSE power source. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version...
XMS7224S CLI Manual - Page 224
The software provides support for classifying and blocking specific types of Denial of ICMP Ping packets. You can configure your system to configure Denial of Service (DoS) Control. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
Software Rev: xxx xxx xxx Serial Num: xxx xxx xxx Mfg Name: xxx xxx xxx Model Name: xxx xxx xxx Asset ID...
XMS7224S CLI Manual - Page 265
ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
Term Reject Routes Total Routes
Definition ...RIP route preference value. Routing Commands
v1.0, November 2010
4-19 A route with a preference of reject routes installed by all protocols. Format Modes
show ip route preferences
This command displays detailed information about the route preferences.
...
XMS7224S CLI Manual - Page 327
... of the Auto Install process ends further periodic requests for a host-specific file. This is most optimally done when the switch is disconnected from a TFTP server. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
boot autoinstall auto-save
This command is used to enable automatically saving the downloaded configuration on the switch. Default Format Mode
Disabled...
XMS7224S CLI Manual - Page 331
...: Event log information is the switch identifier. The is retained across a switch reset. The event code. Format Mode
show hardware
This command displays inventory information for the event. The line number of the event.
show hardware Privileged EXEC
Utility Commands
6-7
v1.0, November 2010 ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
show eventlog...
XMS7224S CLI Manual - Page 453
... to enforce a minimum number of lowercase letters that a password should contain. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
no passwords strength minimum uppercase-letters
Use this command to reset the minimum number of uppercase letters to the default value. Format Mode Default
passwords strength minimum lowercase-letters Global Config 2
Management Commands...
XMS7224S CLI Manual - Page 455
... on that set of characters more than the configured limit, it fails to configure. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
no passwords strength minimum special-letters
Use this command to reset the maximum number of consecutive characters to the default value. The valid range is 0. Format Mode Default
passwords strength maximum consecutive...
XMS7224S CLI Manual - Page 456
...
Management Commands
v1.0, November 2010
7-40 Format Mode Default
passwords strength minimum character-classes Global Config 4
no passwords strength minimum character-classes
Use this command to reset the minimum number of 3 keywords. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
no passwords strength maximum repeated-characters
Use this command to reset...
XMS7224S CLI Manual - Page 496
... IPv6 routing. ProSafe XSM7224S Managed Stackable Switch CLI Manual, Software Version 9.0
copy (pre-login banner) The copy command includes the option to upload or download the CLI Banner to provide the maximum system usage for a specific function. Default Format
Mode
none copy nvram:clibanner
copy nvram:clibanner Privileged EXEC
set prompt Privileged EXEC
Switch Database Management (SDM...
XSM7224S Hardware Installation Guide - Page 6
...: The power module is present, is occurring on the port. • Blinking Yellow - Managed Stackable Switch XSM7224S
l Table 1.
LED Descriptions for XSM7224S
LED ID Stack Master
Power
Fan
10GBT Ports (2 LEDs per port)
Left side LED
1G/10G Link/ACT LED:
• Off: No 1G/10G link is established on the port. • Blinking Green -
XSM7224S Hardware Installation Guide - Page 9
... Managed Switch CLI Manual, Version 9.0 - NETGEAR Installation Guide for the Managed Stackable Layer 2+ 10G Switch XSM7224S. This Hardware Installation Guide • ProSafe NMS100 Network Management System 30-day trial CD-ROM
Protecting Against Electrostatic Discharge
WARNING! Package Contents
Each switch is packed and shipped separately. NETGEAR 7000 Series Managed Switch Administration Guide...
Netgear XSM7224S Reviews
We have not received any reviews for Netgear yet.