Installation Guide
Page 6
... 10BASE-T and 100BASE-T specifications Introduction 1-1 By installing the Model FE508 or Model FE516 hub in the future. Users who have the following background and experience: • Working knowledge of the NETGEAR™ Model FE508 8-port Fast Ethernet Hub or the Model FE516 16-port Fast Ethernet Hub. By migrating users who can increase the bandwidth and improve response times...
... 10BASE-T and 100BASE-T specifications Introduction 1-1 By installing the Model FE508 or Model FE516 hub in the future. Users who have the following background and experience: • Working knowledge of the NETGEAR™ Model FE508 8-port Fast Ethernet Hub or the Model FE516 16-port Fast Ethernet Hub. By migrating users who can increase the bandwidth and improve response times...
Installation Guide
Page 7
...100 Mbps) products. • Stackable architecture allows starting with as few as 8 ports and growing the network as required by stacking up to four hubs for a total of the 100BASE-T ports (Port 8 on the Model FE508 hub and Port 16 on the Model FE516 hub) for connection to provide network traffic... status for the hub. − Normal/Uplink push button for configuration errors. • Stackable chassis equipped with no ...
...100 Mbps) products. • Stackable architecture allows starting with as few as 8 ports and growing the network as required by stacking up to four hubs for a total of the 100BASE-T ports (Port 8 on the Model FE508 hub and Port 16 on the Model FE516 hub) for connection to provide network traffic... status for the hub. − Normal/Uplink push button for configuration errors. • Stackable chassis equipped with no ...
Installation Guide
Page 10
... 2-1 describes each LED on the network. CAUTION: 100 Mbps operation requires the use of the Model FE508 hub provides 8 RJ-45 100BASE-TX ports and the Model FE516 provides 16 RJ-45 100BASE-TX ports. Two LEDs are described in Appendix B, "Connector Pin Assignments." Both LEDs are positioned at the top corners of each RJ...
... 2-1 describes each LED on the network. CAUTION: 100 Mbps operation requires the use of the Model FE508 hub provides 8 RJ-45 100BASE-TX ports and the Model FE516 provides 16 RJ-45 100BASE-TX ports. Two LEDs are described in Appendix B, "Connector Pin Assignments." Both LEDs are positioned at the top corners of each RJ...
Installation Guide
Page 11
...on the cross-over cable to connect the two ports (refer to select Uplink (MDI-X) or Normal (MDI) wiring for Port 8 on the Model FE508 hub and Port 16 on the Model FE516 hub. Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs Normal/Uplink Push Button The Normal/Uplink push button... (see Figure 2-3) on the front panel of the hub allows you are connecting the ...
...on the cross-over cable to connect the two ports (refer to select Uplink (MDI-X) or Normal (MDI) wiring for Port 8 on the Model FE508 hub and Port 16 on the Model FE516 hub. Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs Normal/Uplink Push Button The Normal/Uplink push button... (see Figure 2-3) on the front panel of the hub allows you are connecting the ...
Installation Guide
Page 27
...sure the Normal/Uplink push button is in the Uplink position. Installation Guide for excessive collisions. Excessive collisions can result when multiple hubs are cascaded and when many computers are using a straight-through cable connected to an MDI-X-wired device, make sure the Normal/Uplink... transmit data on the network simultaneously. Troubleshooting 4-3 Troubleshooting (continued) Symptom Collision LED blinking LEDs Collision on Problems with Port 8 on the Model FE508 hub or with Port 16 on the Model FE516 hub Check Collisions are other causes for the Model FE508 and...
...sure the Normal/Uplink push button is in the Uplink position. Installation Guide for excessive collisions. Excessive collisions can result when multiple hubs are cascaded and when many computers are using a straight-through cable connected to an MDI-X-wired device, make sure the Normal/Uplink... transmit data on the network simultaneously. Troubleshooting 4-3 Troubleshooting (continued) Symptom Collision LED blinking LEDs Collision on Problems with Port 8 on the Model FE508 hub or with Port 16 on the Model FE516 hub Check Collisions are other causes for the Model FE508 and...
Installation Guide
Page 35
... and the pin out information for the Uplink (MDI) port (Port 8 on the Model FE508 and Port 16 on the RJ-45 connectors that are used to Port 8 on the Model FE508 hub and Port 16 on hubs. RJ-45 Connector The RJ-45 connector is used for port connections on the Model FE516 hub. or four-pair Category 5 UTP cable. Figure B-1.
... and the pin out information for the Uplink (MDI) port (Port 8 on the Model FE508 and Port 16 on the RJ-45 connectors that are used to Port 8 on the Model FE508 hub and Port 16 on hubs. RJ-45 Connector The RJ-45 connector is used for port connections on the Model FE516 hub. or four-pair Category 5 UTP cable. Figure B-1.