Maytag UMV1160CS Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag UMV1160CS manuals!
Problems with Maytag UMV1160CS?
Ask a Question
Free Maytag UMV1160CS manuals!
Problems with Maytag UMV1160CS?
Ask a Question
Popular Maytag UMV1160CS Manual Pages
Installation Instructions - Page 2
...) or wall template
G. See the "Venting Design Specifications" section.
2 NOTE: The hardware items listed here are for wall or roof venting. Power supply cord bushing (1) ■■ Aluminum grease filters
H. See User Instructions.)
NOTE: Depending on reordering, see the "Replacement Parts" section.
Read and follow the instructions provided with any tools listed here.
■■...
Installation Instructions - Page 3
...
Check the opening .
■■ Support for use as a rear wall template. 1. See the "Installation Dimensions" illustration.
■■ Minimum ... typical for "Mark Rear Wall" part of the installation.
Check with your model, skip "Remove Cardboard Template" steps... Set the cardboard template to the side and refer to Round Transition" illustration in the "Venting Design Specifications" ...
Installation Instructions - Page 4
...fire, or electrical shock. Failure to whether the microwave oven is properly installed and grounded. SAVE THESE INSTRUCTIONS
4 Required: ■■ A 120 V, 60 Hz, AC ...circuit breaker ■■ A separate circuit serving only this microwave oven
GROUNDING INSTRUCTIONS
For all governing codes and ordinances. Observe all cord connected appliances: The microwave oven must be ...
Installation Instructions - Page 5
INSTALLATION INSTRUCTIONS
Remove Mounting Plate
Depending on your model, the mounting plate may be in the foam packaging, or it aside. 3. If the mounting plate is attached to the microwave oven, do not grip or use the door or door handle while the microwave oven is set for recirculation installation.
A
Wall Venting Installation Only
1.
Blower motor wire...
Installation Instructions - Page 6
...screws removed in Step 1 of microwave oven. Damper plate tabs D. Repeat Step 4 from "Wall Venting Installation Only." 3. Reattach blower motor to back of the microwave oven. Screws C. Screws C. Slots
9. A...rectangular vent covers on the damper plate removed in the top of "Wall Venting Installation Only." Reattach blower motor to the microwave oven. 8.
Exhaust Port 9. Make...
Installation Instructions - Page 7
... center of the vertical centerline
(see the "Mark Rear Wall" section), only recirculation or roof
venting installation can be done.
No Wall Studs at End Holes Figure 1
No Wall Studs at End Holes Figure 4
B
D
B
A
A,D
A,D
A,D
E
E
E
E
C
C
C
C
F
F
A. Support tabs F. See illustrations in "Possible Wall Stud Configurations."
See illustrations in "Possible Wall Stud...
Installation Instructions - Page 8
... plate's end holes and bottom edge.
4. Set the mounting plate aside. Using a straightedge, ...(35.96 cm) from the centerline.
8
With the support tabs facing forward (see illustrations in the "Locate Wall ...2 hole(s) through the marks made in the "Locate Wall Stud(s)" section.
Wall Venting Installation Only
Upper cabinet bottom
³⁄₈" (1 cm)
4" (10.2 cm)
Centerline...
Installation Instructions - Page 9
... screws and bolts. Spring toggle nut D. Insert lag screw(s) into the hole(s) drilled into wall stud(s) in Step 2 of "Installation for No Wall Studs at Both End Holes (Figure 4)
1. With the support tabs of the mounting plate facing forward, insert a 3/16-24 x 3" round-head bolt through the wall and to open . Position...
Installation Instructions - Page 10
... away from the microwave oven.
For Roof Venting Installation Only: 7. Damper assembly C. Remove all contents from the rear wall to the thickest part of the microwave oven. NOTES:
■■...saw, cut into the upper cabinet align with tape or thumbtacks. Disconnect power to use as guides.
■■ If the wall behind the microwave oven (as shown.
The template has trim...
Installation Instructions - Page 11
...of mounting plate, and set aside on support tabs at least one ...Install the Microwave Oven
WARNING
5.
If adjustment is no gap between the upper cabinet bottom and the microwave oven.
Tighten bolts until there is required, rotate microwave oven downward. The blocks must be added. NOTE: To avoid damage to be adjusted, skip steps 7 through 6. 11. A
A. Place a washer on your model...
Installation Instructions - Page 12
A
15-20 mm
B
Complete Installation
1. Refer to the User Instructions for troubleshooting information. Bolt B. Insert damper assembly through ...Replace the fuse or reset the circuit breaker. The installation is not positioned as shown. Reconnect power. 4. If the problem continues, call an electrician.
■■ Check that a circuit breaker has not tripped.
Install filters...
Installation Instructions - Page 13
VENTING DESIGN SPECIFICATIONS
This section is intended for wall venting only) D. For optimal venting installation, we recommend:
■■ Using roof or wall caps that...there is used, be sure to seal exterior wall or roof opening around cap.
■■ Not installing 2 elbows together, for use when figuring vent length.
Rectangular-to-Round Transition NOTE: The minimum 3"...
Installation Instructions - Page 14
... of the installation hardware needs to keep the damper from your model and serial numbers located on the front frame of available replacement parts.
If you...Upper Cabinet Template
■■ Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the User Guide.
ASSISTANCE
Call your authorized dealer or service center for details.
14 Accessories
Filler Panel Kits are ...
Maytag UMV1160CS Reviews
We have not received any reviews for Maytag yet.