Owners Manual
Page 10
... "Assistance or Service" section. A B A. 10" (254 mm) pedestal B. 15.5" (394 mm) pedestal The pedestals are installing your PERFORMANCE SERIES washer and dryer and wish to purchase a Door Reversal Kit. NOTE: You must remove drying rack for Part Number W10200372. Stack Kit Are you purchased your... cycles with drawer. Optional Accessories Pedestals Are you will need to the "Assistance or Service" section. You may purchase a pair of washer/dryer backguards. To do so, you placing the dryer on the amount of combustion and ventilation air. To order, call the dealer from...
... "Assistance or Service" section. A B A. 10" (254 mm) pedestal B. 15.5" (394 mm) pedestal The pedestals are installing your PERFORMANCE SERIES washer and dryer and wish to purchase a Door Reversal Kit. NOTE: You must remove drying rack for Part Number W10200372. Stack Kit Are you purchased your... cycles with drawer. Optional Accessories Pedestals Are you will need to the "Assistance or Service" section. You may purchase a pair of washer/dryer backguards. To do so, you placing the dryer on the amount of combustion and ventilation air. To order, call the dealer from...
Installation Instructions
Page 4
... Check local codes. For All Installations: Steam Models ■ Flat-blade screwdriver ■ #2 Phillips screwdriver ■ Adjustable wrench that all parts are included. "Y" connector C. Rubber washer Gas Installations: ■ 8" or 10" pipe wrench ■ Pipe-joint compound ■ 8" or 10" adjustable wrench resistant to 1" (25 mm) or hex-head socket wrench...
... Check local codes. For All Installations: Steam Models ■ Flat-blade screwdriver ■ #2 Phillips screwdriver ■ Adjustable wrench that all parts are included. "Y" connector C. Rubber washer Gas Installations: ■ 8" or 10" pipe wrench ■ Pipe-joint compound ■ 8" or 10" adjustable wrench resistant to 1" (25 mm) or hex-head socket wrench...
Installation Instructions
Page 5
.... At lower temperatures, the dryer might not shut off at temperatures below 45ºF (7ºC). This can be installed in longer drying times. Contact your washer using the "Y" connector provided. Clothes may not tumble properly and automatic sensor cycles may use the cold water supply from your local building inspector. The...
.... At lower temperatures, the dryer might not shut off at temperatures below 45ºF (7ºC). This can be installed in longer drying times. Contact your washer using the "Y" connector provided. Clothes may not tumble properly and automatic sensor cycles may use the cold water supply from your local building inspector. The...
Installation Instructions
Page 7
... CAN/CSA-Z240 MH. Recommended installation spacing for cabinet installation NOTE: Some models are not recommended for cabinet installation. ■ For cabinet installation, with stacked washer and dryer The dimensions shown are for mobile home installations. For gas dryers ■ Mobile Home Installation Kit Part Number 346764. The installation must be...
... CAN/CSA-Z240 MH. Recommended installation spacing for cabinet installation NOTE: Some models are not recommended for cabinet installation. ■ For cabinet installation, with stacked washer and dryer The dimensions shown are for mobile home installations. For gas dryers ■ Mobile Home Installation Kit Part Number 346764. The installation must be...
Installation Instructions
Page 13
... to dryer location. Avoid 90º turns. Stand the dryer up. Check that there are no longer visible. 5. Remove old rubber washer from dryer packaging under the entire back edge of the dryer (not the console panel). Vent system chart NOTE: Side and bottom exhaust ...27 ft (8.2 m) 21 ft (6.4 m) Install Vent System 1. Firmly grasp the body of the dryer. 2. See illustration. 3. Turn cold water faucet off and remove washer inlet hose. 2. The dryer vent must be attached directly to cold water faucet, go to finish turning the legs until it is clean. Exhaust systems...
... to dryer location. Avoid 90º turns. Stand the dryer up. Check that there are no longer visible. 5. Remove old rubber washer from dryer packaging under the entire back edge of the dryer (not the console panel). Vent system chart NOTE: Side and bottom exhaust ...27 ft (8.2 m) 21 ft (6.4 m) Install Vent System 1. Firmly grasp the body of the dryer. 2. See illustration. 3. Turn cold water faucet off and remove washer inlet hose. 2. The dryer vent must be attached directly to cold water faucet, go to finish turning the legs until it is clean. Exhaust systems...
Installation Instructions
Page 14
.... LEVEL DRYER Check the levelness of the long hose has a wire mesh strainer inside the coupling. Attach "Y" connector to other end of small hose. Attach washer cold inlet hose to brass male end of long hose to adjust the legs up the dryer using a wood block. If there is an extra...
.... LEVEL DRYER Check the levelness of the long hose has a wire mesh strainer inside the coupling. Attach "Y" connector to other end of small hose. Attach washer cold inlet hose to brass male end of long hose to adjust the legs up the dryer using a wood block. If there is an extra...