Owners Manual
Page 4
...storage. ACCESSORIES Customize your dealer, or visit: www.maytag.com. 15" Pedestal Color matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. Stack Kit If space is at a premium,... the stack kit allows the dryer to a more information on top of the washer. 4 Worksurface The worksurface bridges the washer and dryer, and provides a ...
...storage. ACCESSORIES Customize your dealer, or visit: www.maytag.com. 15" Pedestal Color matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. Stack Kit If space is at a premium,... the stack kit allows the dryer to a more information on top of the washer. 4 Worksurface The worksurface bridges the washer and dryer, and provides a ...
Installation Instructions
Page 4
... knife Tin snips (new vent installations) Pipe-joint compound resistant to LP gas Parts supplied: Parts package is a registered trademark of Saturn Fasteners, Inc. 4 Rubber washers Parts needed for gas installations: Flat-blade screwdriver #2 Phillips screwdriver 8" or 10" pipe wrench 8" or 10" adjustable wrench (for door reversal only) ® TORX is...
... knife Tin snips (new vent installations) Pipe-joint compound resistant to LP gas Parts supplied: Parts package is a registered trademark of Saturn Fasteners, Inc. 4 Rubber washers Parts needed for gas installations: Flat-blade screwdriver #2 Phillips screwdriver 8" or 10" pipe wrench 8" or 10" adjustable wrench (for door reversal only) ® TORX is...
Installation Instructions
Page 5
... 18" (460 mm) above floor. NOTE: No other fuel-burning appliance can be exposed to shut off at temperatures below 40° F (4° C). Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of installation and servicing; Also consider weight...
... 18" (460 mm) above floor. NOTE: No other fuel-burning appliance can be exposed to shut off at temperatures below 40° F (4° C). Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of installation and servicing; Also consider weight...
Installation Instructions
Page 12
... Connect Inlet Hose The dryer must fit over the exhaust hood. Check and see if rubber washer is in the "Y" connector. Attach short hose to exhaust hood with new rubber washer provided. Record hose installation or replacement dates on faucet. Do not use to reduce the risk...bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. See figure A. Install exhaust hood 12" min. (305 ...
... Connect Inlet Hose The dryer must fit over the exhaust hood. Check and see if rubber washer is in the "Y" connector. Attach short hose to exhaust hood with new rubber washer provided. Record hose installation or replacement dates on faucet. Do not use to reduce the risk...bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. See figure A. Install exhaust hood 12" min. (305 ...
Installation Instructions
Page 13
.... Damage to other end of long hose to dryer fill valve and tighten coupling A Using pliers, tighten the couplings with additional two-thirds turn . Attach washer cold inlet hose to the coupling can result. 6. Damage to the coupling can result. Using pliers, tighten the couplings an additional two-thirds turn. 3. NOTE...
.... Damage to other end of long hose to dryer fill valve and tighten coupling A Using pliers, tighten the couplings with additional two-thirds turn . Attach washer cold inlet hose to the coupling can result. 6. Damage to the coupling can result. Using pliers, tighten the couplings an additional two-thirds turn. 3. NOTE...