Owners Manual
Page 4
...www.maytag.com/accessories. Drying Rack The Drying Rack provides a stationary drying surface for more information. Time tested engineering that meets our strict quality specifications. In Canada, call us at a premium, the stack kit allows the dryer to a more information on top of the washer. For...words represent quality parts and accessories designed specifically for your appliance: Customize your dealer, call 1-800-688-2002 or visit: www.maytag.ca 4 15" Pedestal Color-matched pedestal raises the dryer to be installed on options and ordering, contact your new dryer with ...
...www.maytag.com/accessories. Drying Rack The Drying Rack provides a stationary drying surface for more information. Time tested engineering that meets our strict quality specifications. In Canada, call us at a premium, the stack kit allows the dryer to a more information on top of the washer. For...words represent quality parts and accessories designed specifically for your appliance: Customize your dealer, call 1-800-688-2002 or visit: www.maytag.ca 4 15" Pedestal Color-matched pedestal raises the dryer to be installed on options and ordering, contact your new dryer with ...
Installation Instructions
Page 4
...) and 5/16" (8 mm) nut driver (recommended) Level Pipe-joint compound resistant to 1" (25 mm) or hex-head socket wrench Wire stripper (direct wire installations) 4 Rubber washer 5' (1.52 m) inlet hose Parts package is located in dryer drum. INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation.
...) and 5/16" (8 mm) nut driver (recommended) Level Pipe-joint compound resistant to 1" (25 mm) or hex-head socket wrench Wire stripper (direct wire installations) 4 Rubber washer 5' (1.52 m) inlet hose Parts package is located in dryer drum. INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation.
Installation Instructions
Page 5
...), install Extended Dryer Feet Kit, Part Number 279810. If using a pedestal, you will need 18" (460 mm) to water and/or weather. Maytag® Models IMPORTANT: Do not operate, install, or store dryer where it will be exposed to bottom of 20-120 psi (138-827 kPa). ...Lower temperatures may not operate correctly. ■■ For garage installation, place dryer at least 18" (460 mm) above floor. Contact your washer's water supply by purchasing the necessary parts noted in longer drying times. *Approx. Check local codes. If using power supply cord, a grounded electrical ...
...), install Extended Dryer Feet Kit, Part Number 279810. If using a pedestal, you will need 18" (460 mm) to water and/or weather. Maytag® Models IMPORTANT: Do not operate, install, or store dryer where it will be exposed to bottom of 20-120 psi (138-827 kPa). ...Lower temperatures may not operate correctly. ■■ For garage installation, place dryer at least 18" (460 mm) above floor. Contact your washer's water supply by purchasing the necessary parts noted in longer drying times. *Approx. Check local codes. If using power supply cord, a grounded electrical ...
Installation Instructions
Page 21
... on coupling by hand until it is seated on faucet. NOTE: Do not overtighten. Attach 2 ft. (0.6 m) inlet hose to the coupling can result. Attach washer cold inlet hose to other side of the 5 ft. (1.5 m) inlet hose ends to the "Y" connector. Damage to the cold water faucet using the new inlet...reference. Do not use to "Connect Vent." Screw on coupling by hand until it is seated on connector. 21 Turn cold water off and remove washer inlet hose. The dryer must be connected to the coupling can result. 4. CONNECT INLET HOSE (STEAM MODEL ONLY) For non-steam models, skip ...
... on coupling by hand until it is seated on faucet. NOTE: Do not overtighten. Attach 2 ft. (0.6 m) inlet hose to the coupling can result. Attach washer cold inlet hose to other side of the 5 ft. (1.5 m) inlet hose ends to the "Y" connector. Damage to the cold water faucet using the new inlet...reference. Do not use to "Connect Vent." Screw on coupling by hand until it is seated on connector. 21 Turn cold water off and remove washer inlet hose. The dryer must be connected to the coupling can result. 4. CONNECT INLET HOSE (STEAM MODEL ONLY) For non-steam models, skip ...
Instruction Sheet
Page 1
.... Damage to the coupling can result. 8. Attach other side of small hose. Damage to the "Y" connector. Do not use old hoses. Attach washer cold inlet hose to other end of 5' (1.5 m) inlet hose to fill valve at bottom or top of dryer back panel (depending on connector. ...heck that the water faucets are in place. 3. Attach 2' (0.6 m) inlet hose to the end of "Y" connector. The dryer must be sure rubber washers are on connector. Damage to the coupling can result. 5. Attach "Y" connector to cold water faucet. Inspect hoses to be connected to the coupling can ...
.... Damage to the coupling can result. 8. Attach other side of small hose. Damage to the "Y" connector. Do not use old hoses. Attach washer cold inlet hose to other end of 5' (1.5 m) inlet hose to fill valve at bottom or top of dryer back panel (depending on connector. ...heck that the water faucets are in place. 3. Attach 2' (0.6 m) inlet hose to the end of "Y" connector. The dryer must be sure rubber washers are on connector. Damage to the coupling can result. 5. Attach "Y" connector to cold water faucet. Inspect hoses to be connected to the coupling can ...