Installation Guide
Page 4
... (steam models): "Y" connector 2' (0.6 m) inlet hose Caulking gun and compound (new vent installations) Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in dryer drum. NOTE: Do not use leveling legs supplied with dryer if installing with dryer) ■■Vent clamps ■...
... (steam models): "Y" connector 2' (0.6 m) inlet hose Caulking gun and compound (new vent installations) Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in dryer drum. NOTE: Do not use leveling legs supplied with dryer if installing with dryer) ■■Vent clamps ■...
Installation Guide
Page 5
... for a gas dryer or 30 amp circuit for an electric dryer. ■■If using a pedestal, you will need : ■■A location allowing for your washer using the supplied "Y" connector and a short hose (which you will need 18" (460 mm) to bottom of dryer. ■■The dryer must support dryer...
... for a gas dryer or 30 amp circuit for an electric dryer. ■■If using a pedestal, you will need : ■■A location allowing for your washer using the supplied "Y" connector and a short hose (which you will need 18" (460 mm) to bottom of dryer. ■■The dryer must support dryer...
Installation Guide
Page 13
... NOTE: Do not overtighten. NOTE: Replace inlet hoses after 5 years of use old hoses. Tighten couplings Using pliers, tighten the couplings with new rubber washer. 2. Attach short hose and "Y" connector Attach one of the 2 ft (0.6 m) inlet hose. Damage to cold water faucet. Attach 2 ft (0.6 ...m) inlet hose to the coupling can result. 4. Attach long hose to the "Y" connector. Attach washer cold inlet hose to reduce the risk of "Y" connector. NOTE: Do not overtighten. Screw on coupling by hand until it is seated on connector. ...
... NOTE: Do not overtighten. NOTE: Replace inlet hoses after 5 years of use old hoses. Tighten couplings Using pliers, tighten the couplings with new rubber washer. 2. Attach short hose and "Y" connector Attach one of the 2 ft (0.6 m) inlet hose. Damage to cold water faucet. Attach 2 ft (0.6 ...m) inlet hose to the coupling can result. 4. Attach long hose to the "Y" connector. Attach washer cold inlet hose to reduce the risk of "Y" connector. NOTE: Do not overtighten. Screw on coupling by hand until it is seated on connector. ...
Use & Care Guide
Page 4
... your dealer, call 1-800-807-6777, or visit: www.maytag.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. Stack Kit If space is at 1-800-901-2042,... or visit: www.maytag.com/accessories. Drying Rack The Drying Rack provides a stationary drying surface for more comfortable...
... your dealer, call 1-800-807-6777, or visit: www.maytag.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. Stack Kit If space is at 1-800-901-2042,... or visit: www.maytag.com/accessories. Drying Rack The Drying Rack provides a stationary drying surface for more comfortable...
Instruction Sheet
Page 1
...purchased your dryer or an authorized service company. 2' (0.6 m) Inlet hose CONNECT INLET HOSES 1. Turn cold water faucet off and remove washer inlet hose. 7. Using pliers, tighten the couplings an additional two-thirds turn . NOTE: Do not overtighten. Screw on coupling by... is seated on fill valve connector. 4. Using pliers, tighten the couplings with an additional two-thirds turn . 2. Remove old rubber washer from inlet hose and replace with dryer) 5' (1.5 m) Inlet Hose Your installation may require additional parts. NOTE: Do not overtighten. W10701405A...
...purchased your dryer or an authorized service company. 2' (0.6 m) Inlet hose CONNECT INLET HOSES 1. Turn cold water faucet off and remove washer inlet hose. 7. Using pliers, tighten the couplings an additional two-thirds turn . NOTE: Do not overtighten. Screw on coupling by... is seated on fill valve connector. 4. Using pliers, tighten the couplings with an additional two-thirds turn . 2. Remove old rubber washer from inlet hose and replace with dryer) 5' (1.5 m) Inlet Hose Your installation may require additional parts. NOTE: Do not overtighten. W10701405A...
Installation Guide
Page 3
... that connect to the dryer must end in ring terminals or spade terminals with dryer) Refer to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in dryer drum. Tools needed (steam models): Utility knife Tape measure Level Pliers Caulking gun and compound (for your Use and...
... that connect to the dryer must end in ring terminals or spade terminals with dryer) Refer to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in dryer drum. Tools needed (steam models): Utility knife Tape measure Level Pliers Caulking gun and compound (for your Use and...
Installation Guide
Page 4
... electrical outlet located within 4 ft. (1.2 m) of the water fill valves and water pressure of installation and servicing, spacing for companion appliances, and clearances for your washer using a pedestal, you will need : ■■A location allowing for exhaust vent with maximum slope of 1" (25 mm) under entire dryer. You may use the...
... electrical outlet located within 4 ft. (1.2 m) of the water fill valves and water pressure of installation and servicing, spacing for companion appliances, and clearances for your washer using a pedestal, you will need : ■■A location allowing for exhaust vent with maximum slope of 1" (25 mm) under entire dryer. You may use the...
Installation Guide
Page 15
... drying times and increased energy usage. Record hose installation or replacement dates on the serial number plate in the inner door well. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. ELE - Use clamps to seal exterior wall opening around exhaust hood. 2. Install ... cold water faucet using elbows or making turns, allow as much room as possible. ■■Bend vent gradually to exhaust hood with new rubber washer. 15 Avoid 90° turns. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold ...
... drying times and increased energy usage. Record hose installation or replacement dates on the serial number plate in the inner door well. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. ELE - Use clamps to seal exterior wall opening around exhaust hood. 2. Install ... cold water faucet using elbows or making turns, allow as much room as possible. ■■Bend vent gradually to exhaust hood with new rubber washer. 15 Avoid 90° turns. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold ...
Installation Guide
Page 16
... hand until it is seated on cold water faucet Using pliers, tighten the couplings with additional two-thirds turn . Turn on fill valve connector. Attach washer cold inlet hose to other end of long hose to fill valve at bottom of the 5 ft (1.5 m) inlet hose ends to the coupling can result...
... hand until it is seated on cold water faucet Using pliers, tighten the couplings with additional two-thirds turn . Turn on fill valve connector. Attach washer cold inlet hose to other end of long hose to fill valve at bottom of the 5 ft (1.5 m) inlet hose ends to the coupling can result...