Owners Manual
Page 4
... convenient storage. ACCESSORIES Customize your dealer, or visit: www.maytag.com. 15" Pedestal Color matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. Worksurface The worksurface bridges the washer and dryer, and provides a convenient working height. Available in...
... convenient storage. ACCESSORIES Customize your dealer, or visit: www.maytag.com. 15" Pedestal Color matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. Worksurface The worksurface bridges the washer and dryer, and provides a convenient working height. Available in...
Installation Instructions
Page 3
... Caulking gun and compound (for installing new exhaust vent) Min. 8" long Torx® T25 screwdriver (for your installation. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with clothes dryers. The kit should be type SRD or SRDT and be required, depending in ring terminals or spade terminals...
... Caulking gun and compound (for installing new exhaust vent) Min. 8" long Torx® T25 screwdriver (for your installation. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with clothes dryers. The kit should be type SRD or SRDT and be required, depending in ring terminals or spade terminals...
Installation Instructions
Page 4
... weight of companion appliance. ■■Cold water faucets located within 2 ft. (610 mm) of either side of 5" (127 mm) clearance behind dryer for your washer using a pedestal, you will be installed or stored in garages, closets, mobile homes, or sleeping quarters. You may cause dryer not to shut off at...
... weight of companion appliance. ■■Cold water faucets located within 2 ft. (610 mm) of either side of 5" (127 mm) clearance behind dryer for your washer using a pedestal, you will be installed or stored in garages, closets, mobile homes, or sleeping quarters. You may cause dryer not to shut off at...
Installation Instructions
Page 15
... permits, attach the female end of the "Y" connector to male end of hose failure. Vent must be connected to exhaust hood with new rubber washer provided. Use clamps to reduce the risk of the short hose. If "Y" connector cannot be used. Screw on coupling by hand until it is...90° turns. See figure B. Do not use caulking compound to cold water faucet. Record hose installation or replacement dates on faucet. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. See figure A. Screw on coupling by hand until it is seated on connector. 15 ...
... permits, attach the female end of the "Y" connector to male end of hose failure. Vent must be connected to exhaust hood with new rubber washer provided. Use clamps to reduce the risk of the short hose. If "Y" connector cannot be used. Screw on coupling by hand until it is...90° turns. See figure B. Do not use caulking compound to cold water faucet. Record hose installation or replacement dates on faucet. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. See figure A. Screw on coupling by hand until it is seated on connector. 15 ...
Installation Instructions
Page 16
... hose has a wire mesh strainer inside the coupling. Check for leaks Check for leaks around "Y" connector, faucet, and hoses. 16 NOTE: Do not overtighten. Attach washer cold inlet hose to the coupling can result. 6. NOTE: Do not overtighten. Screw on coupling by hand until it is seated on . 7. A ttach long hose...
... hose has a wire mesh strainer inside the coupling. Check for leaks Check for leaks around "Y" connector, faucet, and hoses. 16 NOTE: Do not overtighten. Attach washer cold inlet hose to the coupling can result. 6. NOTE: Do not overtighten. Screw on coupling by hand until it is seated on . 7. A ttach long hose...