Maytag MED6630HW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MED6630HW manuals!
Problems with Maytag MED6630HW?
Ask a Question
Free Maytag MED6630HW manuals!
Problems with Maytag MED6630HW?
Ask a Question
Maytag MED6630HW Videos
Maytag 2019 MHW6630HW & MED6630HW Review
Duration: 7:48
Total Views: 31,037
Duration: 7:48
Total Views: 31,037
Popular Maytag MED6630HW Manual Pages
Specification Sheet - Page 1
...
Reference Material
Install Guide
Use & Care Guide
Warranty
*Results may vary based on select Maytag® washers to get clothes ready in no time. All rights reserved. Front Load Electric Dryer
MED6630H
Chrome Shadow MED6630HC
Also available in the U.S.A. Capacity
Reduce Static Option
Wrinkle Prevent Option with product.
For complete details, see Installation Instructions packed...
Installation Instructions - Page 4
...:
Tools needed (not supplied with a pedestal or a stack kit. Tools needed for gas connections)
1/4" (6 mm) and 5/16" (8 mm) nut driver (recommended)
Level
Pipe-joint compound resistant to propane gas
Parts supplied (all parts are included. NOTE: Do not use leveling legs supplied with dryer if installing with dryer): ■■ Vent clamps ■■ Vent elbows and vent...
Installation Instructions - Page 5
...supply by purchasing the necessary parts noted in longer drying times.
*Approx. Maytag® Models
IMPORTANT: Do not operate, install, or store dryer where it will need :
■■ A location allowing for your Use and Care Guide for information about accessories available for proper exhaust installation. measurement
*Approx. Check local codes.
Some codes limit, or do not permit...
Installation Instructions - Page 6
..." in your dealer. Check code requirements.
Additional installation requirements: This dryer is available to fully open. For further information, see "Assistance or Service" in the same closet as a dryer. For mobile home installation of installation and servicing, spacing for companion appliances, and clearances for purchase
from your Use and Care Guide. ■■ Special provisions...
Installation Instructions - Page 7
...using a power supply cord:
Use a UL Listed power supply cord kit marked for homes built after 1996, dryer circuits involved in ring terminals or spade terminals with a 3-wire ...of the above code standards can be at least 5 ft. (1.52 m) long. If using and follow the instructions provided for (1) new branch-circuit installations after 1996, and all local codes and ordinances. U.S.A....
Installation Instructions - Page 9
... if local codes and gas ...manual shut-off valve
†®TEFLON is certified by a qualified technician.
Gas shut-off valve must be installed in the "Assistance or Service" section of the dryer in
your Use and Care Guide...dryer.
See illustration below.
■■ 1/2" IPS pipe is recommended. ■■ 3/8" approved aluminum or copper tubing is located on the model...
Installation Instructions - Page 10
... shown on the pedestal model. GAS SUPPLY CONNECTION REQUIREMENTS
■■ Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as needed to connect the exhaust vent.
10 BURNER INPUT REQUIREMENTS Elevations above 2,000 ft. (610 m):
■■ When installed above 2,000 ft. (610...
Installation Instructions - Page 17
... 3/8" flexible gas connector B. 3/8" dryer gas pipe
C. 3/8" to 3/8" ... gas company personnel, and authorized service personnel. Install a shut-off valve
1. A recommended connection is used to connect dryer to action of propane gas. ...joint compound on an approved noncorrosive leak-detection solution. If connected to dryer
A. NOTE: For propane gas connections, you must be used ,...
Installation Instructions - Page 18
...
■■ Recommended for exhausting. Review "Vent System Charts" and, if ... best drying performance and to follow these instructions can result in death or fire.
Replace plastic or metal foil vents with lint....supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may result
in reduced airflow and poor performance. ■■ Do not install...
Installation Instructions - Page 19
...instructions...a manufacturer's exhaust cover kit. A. Bottom exhaust installation
Determine vent path: ...Dryer B. Optional exhaust installations: This dryer can result in longer drying ...models except long vent), or through the bottom. Exhaust systems longer than those specified will help achieve best drying performance.
Standard Vent System Chart
Number of 90° elbows
Type of dryer...
Installation Instructions - Page 20
XXXXXXXXXX. Use clamps to dryer location using straightest path possible. Install Vent System
1. A gas model would be DJAV -
Do not use of box/louvered ...metal
130 ft. (39.6 m)
4
Rigid metal
120 ft. (36.6 m)
To determine if your model has a long vent system, refer to the type code located on the serial number plate in the inner door well. Run vent to seal all joints.
ELE ...
Installation Instructions - Page 21
... to the "Y" connector. CONNECT INLET HOSE (STEAM MODEL ONLY)
For non-steam models, skip to the cold water faucet using the new inlet hoses (not supplied). The dryer must be connected to "Connect Vent." Do not use to the coupling can result.
4. Record hose installation or replacement dates on connector. Remove old rubber washer from...
Installation Instructions - Page 23
... may notice an odor when dryer is
recommended to adjust legs up or down, and check again for certain part replacement or repair.
Over time, the buildup of a water softener is first heated.
This dryer automatically runs an installation diagnostic routine at the start dryer.
The odor will reduce product performance. LEVEL DRYER
1. If there is first used...
Installation Instructions - Page 24
...Disconnect wiring from the dryer door before servicing. Tuck wiring into opening.
†®TORX, T20, and T25 are for models with the two screws removed earlier, as shown. Remove door from dryer
Min. 8" (203 ... from the dryer, peel the film from door
Using a T25® screwdriver, remove the two screws securing the door strike to do so can result in hinge. Replace all parts and panels ...
Instruction Sheet - Page 1
... not overtighten. Inlet Hose Connection Instructions for leaks around "Y" connector, faucet, and hoses. Tools needed:
Parts Supplied:
Pliers
"Y" connector
Rubber washer
Parts needed: (Not supplied with new rubber washer provided. To order, please contact the dealer from inlet hose and replace with dryer)
5' (1.5 m) Inlet Hose
Your installation may require additional parts. NOTE: Do not...
Maytag MED6630HW Reviews
We have not received any reviews for Maytag yet.