Makita LXDT04 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita LXDT04 manuals!
Problems with Makita LXDT04?
Ask a Question
Free Makita LXDT04 manuals!
Problems with Makita LXDT04?
Ask a Question
Makita LXDT04 Videos
Makita LXDT04 18 Volt LXT Lithium Ion Cordless Impact Driver Kit
Duration: 1:51
Total Views: 0
Duration: 1:51
Total Views: 0
Makita LXDT04 vs BHP 451
Duration: 1:57
Total Views: 151
Duration: 1:57
Total Views: 151
Popular Makita LXDT04 Manual Pages
Owners Manual - Page 1
IMPORTANTE: Leer antes de usar. 1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Impact Driver Tournevis à Chocs sans Fil Atornillador de Impacto Inalámbrico
LXDT03 LXDT04
012011
IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage.
Owners Manual - Page 2
...battery pack, picking up or carrying the tool. Prevent unintentional starting. Ensure the switch...(Original instructions)
SPECIFICATIONS
Model
LXDT03
LXDT04
Machine...specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Failure to rain or wet conditions.
Save all instructions...
Owners Manual - Page 3
... or familiarity with the charger specified by poorly maintained power tools. 22. in personal injury.
14. Use of the power tool may make a connection from the battery; GEB054-1
CORDLESS IMPACT DRIVER SAFETY WARNINGS
1. A wrench or a key left attached to another battery pack. 25. Dress properly. Use power tools only with these instructions to follow the safety...
Owners Manual - Page 4
... and battery cartridge in locations where the temperature may result in every six months if you notice less tool power. 2. Overcharging shortens the battery service life. 3. Do not use it for maintaining maximum battery life 1. Always stop operating immediately.
Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and...
Owners Manual - Page 5
... during operation when the tool and/or battery are placed under the following situation. Installing or removing battery cartridge
1. Battery protection system (Battery cartridge with the protection system, which automatically cuts off the output power for its long service life. Switch action
1. Install it . To start the tool, simply pull the switch trigger. Star mark
At this time...
Owners Manual - Page 6
... always set the reversing switch lever to the neutral position. Bit 2. Hook 2. Do not use it with a screw. Reversing switch action
1.
Installing or removing driver bit or socket bit
1. Sleeve
1 2
012009
To install the ...the bit according to the instructions above. • When it is difficult to insert the bit, pull the sleeve and insert it will go .
1. To install the hook, insert it into...
Owners Manual - Page 7
...speed will be sure that the bit will affect the torque. 5. Driver bit or socket bit Failure to use a spare battery to determine the proper fastening time for a time longer than shown...the switch trigger so that you use the correct size driver bit or socket bit will cause a reduction in the figures. Discoloration, deformation or cracks may be fastened will not slip off and the
battery ...
Owners Manual - Page 8
... holders securely. Lead wire 2. Keep the carbon brushes clean and free to place the lead wire in brushes by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
1
012020
Use pliers to remove the carbon brush cap of slender shaft or the like.
1. After replacing brushes, insert the battery cartridge into the holes in reverse.
8
Owners Manual - Page 9
... are required because of Makita's Factory or Authorized Service Centers. MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is caused by others: repairs are
recommended for use with your local Makita Service Center. • Screw bits • Hook • Plastic carrying case • Various type of Makita genuine batteries and chargers • Battery protector
NOTE: •...
Parts Breakdown - Page 2
Model LXDT04 Parts list
A = Standard Equipment 〇= Circuit Diagram
Item#
Part...SET HOUSING SET RUBBER PIN 6 INC. 42 LXDT04 NAME PLATE TAPPING SCREW 3X16 SPONGE B SPONGE A F/R CHANGE LEVER SWITCH... COMPLETE RUBBER PIN 4 REAR COVER REAR COVER TAPPING SCREW 3X16 LED CIRCUIT HOUSING SET HOUSING SET RUBBER PIN 6
Q'ty Unit
1
(LXDT04,LXDT04Z)
1
(LXDT04CW)
2 PC.
0
1
8 PC.
1
1
1 PC.
1
2 ...
Parts Breakdown - Page 3
... SCREW M4X12 HOOK HOOK BATTERY COVER DC18RA FAST CHARGER BATTERY BL1830 SET BATTERY BL1815 SET PLASTIC CARRYING CASE PLASTIC CARRYING CASE COMPLETE LATCH SHAFT HANDLE CAUTION LABEL
0
1
1 PC.
1 PC. (LXDT04,LXDT04Z)
1
(LXDT04CW)
1 PC. (LXDT04,LXDT04CW)
1 PC. (LXDT04,LXDT04CW)
2 SET (LXDT04)
2 SET (LXDT04CW)
1 PC. (LXDT04)
1
(LXDT04CW)
2
(LXDT04CW)
1 PC. (LXDT04CW)
1
(LXDT04CW)
1
Makita LXDT04 Reviews
We have not received any reviews for Makita yet.