Makita AN935H Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AN935H manuals!
Problems with Makita AN935H?
Ask a Question
Free Makita AN935H manuals!
Problems with Makita AN935H?
Ask a Question
Makita AN935H Videos
Guide: MAKITA AN935H+AN635H Trigger change
Duration: 1:22
Total Views: 1,412
Duration: 1:22
Total Views: 1,412
Popular Makita AN935H Manual Pages
AN935H Instruction Manual - Page 2
...read this instruction manual carefully before operation. Always check contact element as instructed in the instruction manual. Fasteners ....
4. Tool maintenance
1. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Air pressure Nail length
Nail capacity
Minimum... nail Sheet-collated coil nail Wire-collated coil nail Sheet-collated coil nail
AN935H 1.28 - 2.26 MPa (180 - 320 PSIG) 45 mm - ...
AN935H Instruction Manual - Page 3
...your footing if you leave it setting.
6. To reduce risk of...SAVE THESE INSTRUCTIONS. A tool that tool will not enter the tool in tool operating/ safety instructions.
19...less fatigue by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Always select... maintenance or repairs;
3. To maintain product SAFETY and RELIABILITY, maintenance and repairs should operate...
AN935H Instruction Manual - Page 4
... relation between nailing frequency, applicable pressure and compressor air output. Failure to follow the safety rules stated in this instruction manual may cause serious personal injury. PARTS DESCRIPTION
1
2
3
4 5 ► 1 . Nose adapter (contact element)
INSTALLATION
Selecting compressor
6
3
5
4
4
5
3.5
23
2
1
00
10 20 30 40 50 60
1
1. Thus, for tool. Failure to do so may...
AN935H Instruction Manual - Page 5
... trigger lock lever to assure continuous, efficient nailing operation. Too deep 2. Too shallow
Hook
► 1 .
This should be installed on another side and then secure it may result in misfiring and personal injuries.
Install the hook on either side of the tool. FUNCTIONAL DESCRIPTION
CAUTION: Before adjusting or checking function on potentially...
AN935H Instruction Manual - Page 6
... . Also, keep your surroundings before using the air duster, the driving force of the arrow.
Recessed part
► 1 . ASSEMBLY
CAUTION: Before carrying out any work area by pressing the button on the ...not use the air duster immediately after the oil was applied. Wait until the recessed parts in four places inside the nose adapter fit in the direction of the tool will temporarily...
AN935H Instruction Manual - Page 7
... trigger for the nail length. CAUTION: After the trigger replacement, always check that the tool operates properly before replacing the trigger. Then with any nails before checking the function...set properly in poor nail feeding or tool malfunction.
4. Then place the first nail in the nail rail and the second nail in such a way that the air socket locks firmly into position when installed...
AN935H Instruction Manual - Page 8
... the air hose, and make sure that the hinged part is
factory-installed. CAUTION: When not operating the tool, always lock the trigger by
placing the contact element against the workpiece without pulling the trigger.
8 ENGLISH Trigger
3. Hinged part 2. Refer to the lock position . Set the trigger assembly for contact actuation (Black color)
1. To...
AN935H Instruction Manual - Page 10
...in the figure.
10 ENGLISH NOTICE: Nailing on ceiling or roof. When the driver is worn, replace it stands upright to the driving surface. Driving nails into hard concrete may cause...be obtained. Material thick- Cutting linked sheet
CAUTION: Always disconnect the air hose from the driver guide as shown in combination, enough fastening may not be fastened. WARNING: Use hardened nails ...
AN935H Instruction Manual - Page 11
... trigger lock lever to the lock position , and disconnect the hose before cleaning a jam. 1. Also remove the nails from the tool. Cleaning of compressor, air set and air hose
After operation, always drain the compressor tank and the air filter. Then cap the air fitting with a flat-blade screwdriver or other...
AN935H Instruction Manual - Page 12
... manual....Makita Authorized or Factory Service Centers, always using Makita replacement parts. This Warranty gives you specific legal rights, and you need any other accessories or attachments might present a risk of Makita's Factory or Authorized Service...shows the trouble is caused by others:
• repairs are recommended for more details regarding these accessories, ask your Makita tool ...
AN935H Parts Breakdown - Page 3
...GUIDE REPAIR KIT FOR EXHAUST HOLE INC. 8-11 O-RING 48 O-RING 45 O-RING 58 O-RING 58 HEAD VALVE DRIVER ASS'Y INC. 14 O-RING 28 COMPRESSION SPRING 52 CYLINDER SEPARATOR O RING 56 O RING 45 O RING 36 CYLINDER O RING 40 O RING 75 TOP CAP GASKET AN935H NAME PLATE HOUSING SET CAUTION LABEL INC. 26,27,179 MAKITA...PC. Model AN935H Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
...
AN935H Parts Breakdown - Page 4
... M4X16 REPAIR KIT FOR DUSTER INC. 55-58 O RING 3 O-RING 3 O-RING 5.5 O RING 8 VALVE STEM VALVE GUIDE COMPRESSION SPRING 5 SWITCH LEVER SPRING PIN 2-8 CAP 9 ONE-TOUCH JOINT H22PM HEX. SOCKET HEAD BOLT M5X35 FLAT WASHER 5 MAGAZINE ASSEMBLY INC. 69-86 MAGAZINE COMPLETE CAUTION LABEL PIN 4 TORSION SPRING 7 STOP RING E-3 MAGAZINE CAP COMPLETE AN935H MAGAZINE...
AN935H Parts Breakdown - Page 5
... CLAW TORSION SPRING 4 URETHANE RING 3 PIN 3 COMPRESSION SPRING 12 O-RING 15 O RING 18 O-RING 7 O-RING 12.5 O RING 3 O-RING 3 O RING 18 REPAIR KIT FOR TRIGGER INC. 119-125,177,180 TRIGGER VALVE GUIDE PILOT VALVE COMPRESSION SPRING 3 TRIGGER VALVE STEM TRIGGER VALVE CASE IDLER C TRIGGER S TORSION SPRING 3 SPRING PIN 2-12 TRIGGER ASSY S INC...
AN935H Parts Breakdown - Page 6
WRENCH 4 PLASTIC CARRYING CASE LATCH AN935H PLASTIC CASE LABEL TRIGGER ASSY B TORSION SPRING 3 TRIGGER S IDLER B SPRING PIN 2-12
1 PC. 1 PC. 1 PC. 0 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 ... LOCK LEVER PIN 3 COMPRESSION SPRING 7 DOOR COVER FLAT WASHER 4 HEX. SOCKET HEAD BOLT M4X8 O-RING 6 TOP CAP COVER GRIP O-RING 16.5 NOSE ADAPTER OIL SUPPLY SET SAFETY GOGGLE HEX.
Makita AN935H Reviews
We have not received any reviews for Makita yet.